Commit Graph

58 Commits

Author SHA1 Message Date
Eugen Hristev
367386861b configs: at91: sama5: enable CMD_IMI
Enable iminfo command with CONFIG_CMD_IMI

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
f377f7040e configs: sama5d2_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:41 -04:00
Eugen Hristev
d3d286d38f configs: sama5d2_xplained: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:38 -04:00
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Adam Ford
8ccf98b1cf Convert CONFIG_MISC_INIT_R to Kconfig
This converts the following to Kconfig:
   CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17 13:04:00 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Tom Rini
358b6a20e4 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 11:57:37 -04:00
Eugen Hristev
e75477e4f2 configs: sama5d2_xplained: set default FAT env location to SD-Card
For sama5d2_xplained_mmc_defconfig, we have the following layout for SD-Card:
partition 1: FAT: contains bootstrap binary (second level bootloader),
U-boot, U-boot env, kernel, dtb
partition 2: EXT4: Rootfs.

Add to defconfig CONFIG_ENV_FAT_DEVICE_AND_PART to have environment
by default on SD-Card, to align with our demo layout.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-05-23 17:30:04 -04:00
Eugen Hristev
30db47a9b9 configs: sama5d2_xplained: enable ext4 command support
To support loading the zImage + DTB from the rootfs ext4 partitions,
enable the ext4 command support.

Based on original work by Wenyou Yang

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-05-23 17:30:03 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Tom Rini
34b3722e38 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-17 10:10:47 -04:00
Tom Rini
c9542eae0b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 20:37:13 -04:00
Jagan Teki
89d4fc153b spi: atmel: default y if DM_SPI && ARCH_AT91
ATMEL_SPI is now fully converted to driver-model and
respective boards switch to DM_SPI as well,
so make default y for ARCH_AT91

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
2018-04-06 16:11:09 -04:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Tuomas Tynkkynen
a4fa811463 cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA
cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-05 20:58:11 -05:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Wenyou Yang
d2cd09bb44 board: sama5d2_xplained: Convert to CONFIG_DM_VIDEO
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-29 17:48:56 +02:00
Wenyou Yang
5541543f68 configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment
To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-09-14 16:02:48 -04:00
Wenyou Yang
34e2819d31 board: sama5d2_xplained: Replace code to set mac address
Replace the code to set the ethernet mac address with the code from
the common folder.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11 16:23:07 -04:00
Tom Rini
5dc4dfd2a9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 07:16:32 -04:00
Wenyou.Yang@microchip.com
fc6adebbc1 board: atmel: Use the new PIT timer driver
Use the Atmel PIT timer driver which supports the driver model
and device tree.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-08-26 14:56:09 -04:00
Tom Rini
88663126a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 20:00:40 -04:00
Sam Protsenko
5abc1a4523 common: Move CONFIG_BOOTARGS to Kconfig
Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 17:06:06 -04:00
Tom Rini
43ba3c59cb env: Migrate CONFIG_ENV_IS_IN_FAT options to Kconfig
We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig.  Migrate all existing users to the new
values.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-31 11:22:56 -04:00
Simon Glass
b31e065f89 Convert CONFIG_ENV_IS_IN_FAT to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_FAT

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25 21:34:15 -04:00
Tom Rini
fb82fe3851 configs: Resync defconfigs
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-19 09:47:40 -04:00
Tom Rini
91d27a17c6 Kconfig: Migrate FS_FAT / FAT_WRITE
Now that these symbols are in Kconfig, migrate all users.  Use imply on
a number of platforms that default to having this enabled.  As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-03 17:55:34 -04:00
Wenyou Yang
62904b7346 configs: sama5d2_xplained: update for SPL
Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09 12:14:15 -06:00
Wenyou Yang
d4ce9e7bbf configs: sama5d2_xplained: enable CONFIG_DM_ETH
Enable CONFIG_DM_ETH to make MACB to support driver model.

Because the USB Ether doesn't support driver model so far,
remove this feature.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09 12:14:15 -06:00
Tom Rini
8728c97eff configs: Re-sync
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-13 13:52:33 -04:00
Masahiro Yamada
dd3b64eb56 mmc: atmel: rename CONFIG_ATMEL_SDHCI to CONFIG_MMC_SDHCI_ATMEL
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.

While we are here, add "depends on ARCH_AT91".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-31 21:50:47 +09:00
Masahiro Yamada
e1ce61fbba mmc: move CONFIG_SDHCI to Kconfig, renaming to CONFIG_MMC_SDHCI
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.

This commit was created as follows:

[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'

[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig

[3] run "tools/moveconfig.py -y MMC_SDHCI"

[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-12-29 13:08:12 -05:00
Masahiro Yamada
e298c46ac3 mmc: make MMC driver entries dependent on MMC
Currently, CONFIG_MMC is not related to any other options by
"depends on" or "select".  One of big advantages of using Kconfig
is automatic dependency tracking, but the current state is lacking
it.  As the first step, make the existing MMC driver entries depend
on MMC.

This commit was created by the following steps:

[1] Run the following script:

--------------------8<--------------------
rm -f tmp.txt

for d in $(find . -path './configs/*_defconfig')
do
        if grep -q -e 'CONFIG_MSM_SDHCI=y' $d ||
           grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d ||
           grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d ||
           grep -q -e 'CONFIG_SH_SDHI=y' $d ||
           grep -q -e 'CONFIG_PIC32_SDHCI=y' $d ||
           grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d ||
           grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d ||
           grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d ||
           grep -q -e 'CONFIG_SANDBOX_MMC=y' $d
        then
                echo CONFIG_MMC=y >> $d
                echo ${d#./configs/} >> tmp.txt
        fi
done

tools/moveconfig.py -y -s -d tmp.txt
rm tmp.txt
--------------------8<--------------------

[2] surround MMC driver entries with "if MMC" and "endif"

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-12-29 13:08:07 -05:00
Masahiro Yamada
c27269953b mmc: complete unfinished move of CONFIG_MMC
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.

We generally do not like such partial moves.  This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.

I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.

This commit was created as follows:

[1] Edit Kconfig (remove the "depends on", add the "default",
    copy the prompt and help message from Linux)

[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-12-29 13:08:07 -05:00
Masahiro Yamada
187809517d Sync defconfig files by savedefconfig
Generated by "tools/moveconfig -s".

This will make config moves easier.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-29 13:07:33 -05:00
Wenyou Yang
2992dd833d board: sama5d2_xplained: Enable an early debug UART
Enable an early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-10-28 18:37:15 +02:00
Wenyou Yang
6f170c4d77 board: sama5d2_xplained: Move config options to defconfigs
Move the config options from the include/configs/sama5d2_xplained.h
to configs/sama5d2_xplained_*_defconfig.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-10-28 18:37:15 +02:00
Lokesh Vutla
8435179271 common: Add DISPLAY_BOARDINFO
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures.  Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12 08:20:17 -04:00
Simon Glass
e00f76cee9 Convert CONFIG_SPL_SERIAL_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:19 -04:00
Simon Glass
1fdf7c64ed Convert CONFIG_SPL_MMC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:13 -04:00
Simon Glass
cc4288ef42 Convert CONFIG_SPL_LIBGENERIC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
1646eba85c Convert CONFIG_SPL_LIBDISK_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
77d2f7f507 Convert CONFIG_SPL_LIBCOMMON_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:11 -04:00
Simon Glass
53b5bf3c1d Convert CONFIG_SPL_GPIO_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
ae56db5f1c Convert CONFIG_SPL_FAT_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
c2ae7d8220 Kconfig: Move SPL settings into their own file
Move the SPL settings into common/spl where most of the SPL code is kept.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:03:36 -04:00
Tom Rini
645176d1d5 configs: Migrate CONFIG_USB_STORAGE
In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09 14:59:35 -04:00
Heiko Schocher
bb597c0eeb common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-06-09 13:53:05 -04:00
Marek Vasut
12328f25f2 ARM: atmel: Enable FIT image support for SAMA5Dx
Enable the fitImage support for the entire SAMA5Dx lineup of CPUs.
The fitImage is superior image format to uImage and it is useful
to have it available.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebase on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-05-24 08:08:37 +02:00