This allows us to act like a serial device: we get tab chars and CTRL+C
and respond appropriately.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fix:
ds1337.c: In function 'rtc_get':
ds1337.c:88:52: warning: variable 'control' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
4xx_enet.c: In function 'enet_rcv':
4xx_enet.c:1772:21: warning: variable 'ef_ptr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Fix:
eepro100.c: In function 'read_hw_addr':
eepro100.c:926:6: warning: variable 'eeprom' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
ns8382x.c: In function 'ns8382x_check_duplex':
ns8382x.c:704:6: warning: variable 'hun' set but not used
[-Wunused-but-set-variable]
To fix this, we get rid of the NS8382X_DEBUG code and use standard
debug() instead.
This will now trigger a so far undetected warning:
ns8382x.c:780:2: warning: format '%X' expects argument of type
'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Fix that, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mmc:
tegra2: Move MMC clock initialization into MMC driver
mmc: sdhci: fix sdma bug for large file transfer
mmc: sdhci: add timeout for data transfer
mmc: sdhci: add mmc structure for host
mmc: sdhci: fix build warning
mmc: sdhci: fix cache flush
mmc: CMD7:MMC_CMD_SELECT_CARD response fix
mmc: test mmc bus width on startup
mmc: change magic number to macro define
mmc: mv_sdhci: fix 8bus width access for 88SV331xV5
mmc: retry the cmd8 to meet 74 clocks requirement in the spec
PXA: Add MMC driver using the generic MMC framework
Commit 114d7fc0 "e1000: Rewrite EEPROM checksum error to give more
information" failed to initialize the checksum variable which should
result in random results. Fix that.
Commit 2326a94d caused a ton of "unused variable 'x'" warnings.
Fix these. While we are at it, remove some bogus parens.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
This centralizes knowledge of MMC clocking into the MMC driver. This also
removes clock setup from the board files, which will simplify later changes
that modify the Harmony board to support the correct set of MMC controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
SDHCI spec need to reset the sdma base address while the software
try to accorss the 512k bytes address boundary. When meet such
accross behavior, sdhci controller would generate a interrupt
automatically, and software need handle this.
Signed-off-by: Lei Wen <leiwen@marvell.com>
As per JEDEC document JESD84-A441 (page 105) response for CMD7
(MMC_CMD_SELECT_CARD) response should be R1 instead of R1b. In uboot we
never take MMC to disconnected state and on powerup its always ideal
state which later goes to stand-by state.
from document footnote:
R1 while selecting from Stand-By State to Transfer State; R1b while
selecting from Disconnected State to Programming State.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
For we don't know mmc bus width from reading registers, the only way
to check is to test.
Current compare offset is:
EXT_CSD_PARTITIONING_SUPPORT
EXT_CSD_ERASE_GROUP_DEF
EXT_CSD_REV
EXT_CSD_HC_ERASE_GRP_SIZE
EXT_CSD_SEC_CNT
Signed-off-by: Lei Wen <leiwen@marvell.com>
Previous magic number is hard to parse its meaning, change it to
respective macro definition
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: WOlfgang Denk <wd@denx.de>
Marvell 88SV331xV5 platform's sdhci host control is not very standard
with the spec in the 8bit handling. It need to set its private register
to switch to the 8bit mode which is not included in the standard sdhci
registers.
This patch mainly hacks the writeb method, and set its private register
if it find the driver is going to switch to the 8bit mode.
Signed-off-by: Lei Wen <leiwen@marvell.com>
For some controller it has dynamic clock gating, and only toggle out clk
when the first cmd0 send out, while some card strictly obey the 74
clocks rule, the interval may not be sufficient between the cmd0 and
this cmd8, retry to fulfil the clock requirement.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
This driver may handle multiple PIO cores and thus needs to be
setup by calling the altera_pio_init() function within the early
board setup routine.
The driver comes with some extras, see below the copyleft header.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
As a part of the manufacturing process for some of our custom hardware,
we are programming the EEPROMs attached to our Intel 82571EB controllers
from software using U-Boot and Linux.
This code provides several conditionally-compiled features to assist in
our manufacturing process:
CONFIG_CMD_E1000:
This is a basic "e1000" command which allows querying the controller
and (if other config options are set) performing EEPROM programming.
In particular, with CONFIG_E1000_SPI this allows you to display a
hex-dump of the EEPROM, copy to/from main memory, and verify/update
the software checksum.
CONFIG_E1000_SPI_GENERIC:
Build a generic SPI driver providing the standard U-Boot SPI driver
interface. This allows commands such as "sspi" to access the bus
attached to the E1000 controller. Additionally, some E1000 chipsets
can support user data in a reserved space in the E1000 EEPROM which
could be used for U-Boot environment storage.
CONFIG_E1000_SPI:
The core SPI access code used by the above interfaces.
For example, the following commands allow you to program the EEPROM from
a USB device (assumes CONFIG_E1000_SPI and CONFIG_CMD_E1000 are enabled):
usb start
fatload usb 0 $loadaddr 82571EB_No_Mgmt_Discrete-LOM.bin
e1000 0 spi program $loadaddr 0 1024
e1000 0 spi checksum update
Please keep in mind that the Intel-provided .eep files are organized as
16-bit words. When converting them to binary form for programming you
must byteswap each 16-bit word so that it is in little-endian form.
This means that when reading and writing words to the SPI EEPROM, the
bit ordering for each word looks like this on the wire:
Time >>>
------------------------------------------------------------------
... [7, 6, 5, 4, 3, 2, 1, 0, 15, 14, 13, 12, 11, 10, 9, 8], ...
------------------------------------------------------------------
(MSB is 15, LSB is 0).
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
A followup patch will be adding a configurable feature to enable
programming of E1000 EEPROMs from the command line or via the generic
U-Boot SPI interface.
In order for it to work it needs access to certain E1000-internal
functions, so export those in the e1000.h header file.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
As an aide to debugging, we should print out the expected value of the
EEPROM checksum in addition to just saying that it is wrong.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
By allocating the e1000 device structures much earlier, we can easily
generate better error messages and siginficantly clean things up.
The only user-visable change (aside from reworded error messages) is
that a detected e1000 device which fails to initialize due to software
or hardware error will still be allocated a device number.
As one example, consider a system with 2 e1000 PCI devices where the
first controller has a corrupted EEPROM. Using the old code the
second controller would be "e1000#0", while with this change it would be
"e1000#1".
This change should hopefully make such EEPROM errors much more
straightforward to handle correctly in boot scripts and the like.
It is also necessary for a followup patch which allows SPI programming
of an e1000 controller's EEPROM even if the checksum is invalid.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Consolidate the test for a dual-port NIC to one location for easy
modification, then fix support for the dual-port 82571.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
The debugX() macro was always used with debug level 1. There is no point to use
it here instead of debug().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
fec_mxc.c: In function 'fec_mii_setspeed':
fec_mxc.c:112:2: warning: format '%#lx' expects type 'long unsigned int', but
argument 2 has type 'u32'
fec_mxc.c: In function 'fec_recv':
fec_mxc.c:632:2: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
bus_vcxk.c:167:2: warning: format '%d' expects type 'int', but argument 2 has
type 'u_long'
bus_vcxk.c:167:2: warning: format '%d' expects type 'int', but argument 3 has
type 'u_long'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
ks8695eth.c:199:2: warning: format '%x' expects type 'unsigned int', but
argument 4 has type 'volatile void *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
lattice.c:319:4: warning: format '%x' expects type 'unsigned int', but argument
3 has type 'const char *'
lattice.c:319:4: warning: format '%x' expects type 'unsigned int', but argument
4 has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
kirkwood_spi.c:125:2: warning: format '%08X' expects type 'unsigned int', but
argument 4 has type 'const void *'
kirkwood_spi.c:125:2: warning: format '%08X' expects type 'unsigned int', but
argument 5 has type 'void *'
kirkwood_spi.c:160:5: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'void *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
smsc95xx.c: In function 'smsc95xx_write_hwaddr':
smsc95xx.c:380:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
pxa_mmc.c: In function 'mmc_cmd':
pxa_mmc.c:77:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'ulong'
pxa_mmc.c: In function 'mmc_block_read':
pxa_mmc.c:110:2: warning: format '%d' expects type 'int', but argument 4 has
type 'ulong'
pxa_mmc.c: In function 'pxa_mmc_write':
pxa_mmc.c:327:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:349:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:354:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:362:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:367:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
i82365.c: In function 'cirrus_set_opts':
i82365.c:329: error: 'buf' undeclared (first use in this function)
i82365.c:329: error: (Each undeclared identifier is reported only once
i82365.c:329: error: for each function it appears in.)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
tqm8xx_pcmcia.c: In function 'power_off':
tqm8xx_pcmcia.c:46: warning: passing argument 1 of 'out_be32' makes pointer from
integer without a cast
tqm8xx_pcmcia.c: In function 'power_on_5_0':
tqm8xx_pcmcia.c:52: warning: passing argument 1 of 'out_be32' makes pointer from
integer without a cast
tqm8xx_pcmcia.c: In function 'power_on_3_3':
tqm8xx_pcmcia.c:58: warning: passing argument 1 of 'out_be32' makes pointer from
integer without a cast
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
sata_sil3114.c: In function 'sata_identify':
sata_sil3114.c:174: warning: format '%x' expects type 'unsigned int', but
argument 2 has type 'lbaint_t'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
fsl_pci_init.c: In function 'fsl_pci_init':
fsl_pci_init.c:308: warning: format '%08x' expects type 'unsigned int', but
argument 6 has type 'long unsigned int'
fsl_pci_init.c:347: warning: format '%x' expects type 'unsigned int', but
argument 2 has type 'volatile u32 *'
fsl_pci_init.c: In function 'fsl_pci_init':
fsl_pci_init.c:308: warning: format '%016llx' expects type 'long long unsigned
int', but argument 4 has type 'pci_addr_t'
fsl_pci_init.c:308: warning: format '%016llx' expects type 'long long unsigned
int', but argument 5 has type 'pci_size_t'
fsl_pci_init.c:308: warning: format '%08x' expects type 'unsigned int', but
argument 6 has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
fsl_espi.c: In function 'spi_setup_slave':
fsl_espi.c💯 warning: format '%d' expects type 'int', but argument 3 has type
'long unsigned int'
fsl_espi.c: In function 'spi_xfer':
fsl_espi.c:237: warning: format '%08x' expects type 'unsigned int', but argument
5 has type 'const void *'
fsl_espi.c:237: warning: format '%08x' expects type 'unsigned int', but argument
7 has type 'void *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
ahci.c: In function 'ahci_port_start':
ahci.c:401: warning: format '%x' expects type 'unsigned int', but argument 2 has
type 'struct ahci_cmd_hdr *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 3 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1365: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
4xx_enet.c:1376: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
jedec_flash.c: In function 'fill_info':
jedec_flash.c:393: warning: format '%x' expects type 'unsigned int', but
argument 2 has type 'ulong'
jedec_flash.c:393: warning: format '%x' expects type 'unsigned int', but
argument 3 has type 'ulong'
jedec_flash.c:402: warning: format '%d' expects type 'int', but argument 2 has
type 'ulong'
jedec_flash.c:402: warning: format '%d' expects type 'int', but argument 3 has
type 'ulong'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Scott Wood <scottwood@freescale.com>
cfi_flash.c: In function 'flash_protect_default':
cfi_flash.c:2152: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'ulong'
cfi_flash.c:2152: warning: format '%08x' expects type 'unsigned int', but
argument 3 has type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Scott Wood <scottwood@freescale.com>
cfb_console.c: In function 'video_display_bitmap':
cfb_console.c:1148: warning: format '%d' expects type 'int', but argument 2 has
type 'long unsigned int'
cfb_console.c:1148: warning: format '%d' expects type 'int', but argument 3 has
type 'long unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM
as they are no longer needed with the support for more than 1 PHYs in davinci
emac driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for more than 1 PHYs. Many of the davinci platforms have more
than 1 PHYs on thier board. This patch extends support in davinci emac
driver for upto 3 PHYs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add more features like DUPLEX, 100MB link speed etc to auto negotiate
in EMAC driver. EMAC controller autonegotiates for these features with
PHYs which are on the board.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all omap families define OMAP_HSMMC[23]_BASE so condition those
cases in omap_mmc_init().
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Build pass with following config:
dkb_config
aspenite_config
edminiv2_config
openrd_ultimate_config
sheevaplug_config
mv88f6281gtw_ge_config
rd6281a_config
guruplug_config
km_kirkwood_config
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Wolfgang Denk <wd@denx.de>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Instead of using directly the i2c_set_bus() function,
the I2C_SET_BUS macro must be used to avoid build
errors for targets without multibus I2C.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This commit adds support for MAX8998 PMIC driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
I2C or SPI PMIC devices can be accessed.
Separate files: pmic_i2c.c and pmic_spi.c are responsible
for handling transmission over I2C or SPI bus.
New flags:
CONFIG_PMIC - enable PMIC general device.
CONFIG_PMIC_I2C/SPI - specify the interface to be used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds most of the clock functions required by board and driver code:
-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control
These functions are plumbed in as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
It seems to be good practice to return the number of received bytes in the
eth_device's recv() callback, here: tse_eth_rx().
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Note: This is kind of guess work. The current code is preserved for
all RGMII related modes. It is different for flags=0 (GMII) and flags=5
(SGMII). The last case, SGMII, is successfully tested on
Altera's Terasic DE4.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Currently the mmc_change_freq and mmc_startup functions allocates
buffers on the stack that are passed down to the MMC device driver.
These buffers could be unaligned to the L1 dcache line size. This
causes problems when using DMA and with caches enabled.
This patch correctly cache alignes the buffers used for reading the
ext_csd data from an MMC device.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Currently the sd_change_freq function allocates two buffers on the
stack that it passes down to the MMC device driver. These buffers
could be unaligned to the L1 dcache line size. This causes problems
when using DMA and with caches enabled.
This patch correctly cache alignes the buffers used for reading the
scr register and switch status values from an MMC device.
Change-Id: Ifa8414f572ef907681bd2d5ff3950285a215357d
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Only one board uses this driver (ns9750dev), but the board doesn't seem
to have an entry to actually build it in the Makefile/boards.cfg, so just
delete net support from its board config.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Everyone seems to have converted to the new enc28j60 driver, so drop
this older one which isn't used and doesn't support NET_MULTI.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Do not setup userial_ports array as const because
in uartlite_serial_putc is out_be32 which can't write
to tx_fifo if is const.
Warning log:
serial_xuartlite.c: In function 'uartlite_serial_putc':
serial_xuartlite.c:60: warning: initialization discards qualifiers from pointer target type
serial_xuartlite.c: In function 'uartlite_serial_getc':
serial_xuartlite.c:78: warning: initialization discards qualifiers from pointer target type
serial_xuartlite.c: In function 'uartlite_serial_tstc':
serial_xuartlite.c:87: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Michal Simek <monstr@monstr.eu>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Add the Silicon Image series PCI Express to
Serial ATA controller support, including Sil3132,
Sil3131 and Sil3124.
The SATA controller can be used to load kernel.
The features list:
- Supports 1-lane 2.5 Gbit/s PCI Express
- Supports one/two/four independent Serial ATA channels
- Supports Serial ATA Generation 2 transfer rate of 3.0 Gbit/s
- Supports LBA28 and LBA48
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Aaron Williams <Aaron.Williams@cavium.com>
Tested-by: Lan Chunhe <b25806@freescale.com>
Not draining the FIFO and waiting for the UART to be non-busy
before changing baudrate results in crap characters on the
console, so let's wait for the FIFO to drain and the last
character to be clocked out before we do that.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code had two paths depending on whether the card was to be
accessed from plain memory or the IO region. However the error
path checks whether IO region was obtained - twice. Fix up the
error path according to the probable intention.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch move the reset function from initialization to
driver register procedure.
Some embedded system supports wake on lan nowadays. On this kind of system,
the ftgmac100 will be still supplied power after the system has been
shut-down by Linux. Hence the register used by linux won't be clear
when the system has been powered-off.
The origin ftgmac100 driver in u-boot will only register
driver and functions to network stack and won't reset the ftgmac100
hardware if the network won't be used during boot-up.
This will lead ftgmac100 continue receiving packets and then might corrupt
linux kernel when booting up.
So we reorder the hardware reset function earlier to force the hardware
to be reset whether it will be used or not.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MDIO controller to talk to external PHYs is on FM1-DTSEC1 so don't
allow disabling. If we disable it we end up powering the block down in
the SoC and thus can't communicate to any external PHYs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FM1-DTSEC1's MAC was being marked as disabled if the port was not
configured based on the SoC configuration. However we utilize the MAC
interface for MDIO and thus should NOT mark it disabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a rather subtle build problem where the build time stamp is not
updated for out-of-tree builds if there exists an in-tree build which
has a valid timestamp file. So if you do an in-tree build, then an
out-of-tree build your timestamp will not change.
The correct timestamp_autogenerated.h lives in the object tree, but it
is not always found there. The source still lives in the source tree and
when compiling version.h, it includes timestamp_autogenerated.h. Since
the current directory is always searched first, this will come from the
source tree rather than the object tree if it exists there. This affects
dependency generation also, which means that common/cmd_version.o will not
even be rebuilt if you have ever done an in-tree build.
A similar problem exists with the version file.
This change moves both files into the 'generated' subdir, which is already
used for asm-offsets.h. Then timestamp.h and version.h are updated to
include the files from there.
There are other places where these generated files are included, but I
cannot see why these don't just use the timestamp.h and version.h headers.
So this change also tidies that up.
I have tested this with in- and out-of-tree builds, but not SPL. I have
looked at various other options for fixing this, including sed on the dep
files, -I- and -include flags to gcc, but I don't think they can be made
to work. Comments welcome.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This uart simply writes to stdout and reads from stdin. We might imagine
instead buffering the data so that a test interface can check output and
inject input.
Signed-off-by: Simon Glass <sjg@chromium.org>
commit a45dde2293 changed the dm9000
direct register access to standard IO. This should work
on the ColdFire platform as there are corresponding macros for
the LE devices. But the hardware settings on some ColdFire boards had
swapped the byte order which make the original macros such as out_le16
cannot work. To avoid changing the common io access code on ColdFire
platform, the DM9000_BYTE_SWAPPED define was added to make the dm9000 use
__raw* IO access on some ColdFire boards.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
The function kw_gpio_is_valid returns zero on success, so
adapt the error check accordingly.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Dieter Kiermaier <dk-arm-linux@gmx.de>
mx3fb.c was based on CONFIG_LCD and is moved by this patch to
CONFIG_VIDEO, which has greater freedom in selecting videomodes
even at runtime.
This renders the accumulating list of display defines
(CONFIG_DISPLAY_VBEST..., CONFIG_DISPLAY_C057...) obsolete as
these may be setup through env variables:
uboot> setenv mydisplay 'video=ctfb❌240,y:320,depth:16,mode:0,pclk:185925,
le:9,ri:17,up:7,lo:10,hs:1,vs:1,sync:100663296,vmode:0'
uboot> setenv videomode ${mydisplay}
This commit also fixes the board config files for qong and
imx31_phycore boards as needed. The videomode settings of
previously supported displays are added to CONFIG_EXTRA_ENV_SETTINGS
now. CONFIG_SYS_MALLOC_LEN for imx31_phycore board is increased
to make the frame buffer allocation working with the changed
driver.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Pixel format defines must be available for boards to set up
the right display. Move them and export in a new file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The framebuffer driver for MX5 is based on CONFIG_LCD.
In the current implementation, there is a serious bug
because the required memory is allocated before
relocation, but the driver knows only later which is
the resolution of the display. The patch switches the driver
to CONFIG_VIDEO and the memory is allocated by the driver itself.
We also need to switch the vision2 board code and config file
in the same commit so that this commit will be bisectable.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Update the Freescale DIU video driver (fsl_diu_fb.c) to use linux/fb.h.
Some data structures from this header file were just copied into
fsl_diu_fb.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
PCI cards might need some time after reset to respond. On some
boards (mpc5200 or mpc8260 based) the PCI bus reset is deasserted
at pci_init_board() time, so we currently can not use available
"pcidelay" option for waiting before PCI bus scan since this
waiting takes place before calling pci_init_board(). By moving
the pcidelay code to the new location using of the "pcidelay"
option is possible on mpc5200 or mpc8260 based boards, too.
Since pci_hose_scan() could be called multiple times, restrict
the function to wait only during its first call and to ignore
pcidelay for any further call (as pointed out by Matthias).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Add axi_ethernet driver for little-endian Microblaze.
RX/TX BDs and rxframe buffer are shared among all axi_ethernet MACs.
Only one MAC can work in one time.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Setup RX/TX ping-pong buffer for every emaclite IP separately.
The next patch move initialization directly to board code.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Before the Teranetics TN2020 PHY can be used, the SERDES lanes need to be
aligned, so wait for lane alignment before completing the startup sequence.
Note that this process can take up to three seconds.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EC1_EXT, EC2_EXT, and EC3 bits in the RCW don't officially exist on the
P3060 and should always be set to zero.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jz4740 NAND flash controller can support:
* MLC NAND as well as SLC NAND
* all 8-bit/16-bit NAND flash devices
* HAMMING and RS hardware ECC
* automatic boot up from NAND flash devices
nand_ecclayout is set up for 2GiB NAND chip mounted in Qi LB60.
We'll bring up boot-from-NAND support in nand_spl/ in the future.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
This fixes that u-boot gets stuck when a bitflip was detected
during "ubi part <ubi_device>". If a bitflip was detected UBI tries
to copy the PEB to a different place. This needs that the eba table
are initialized, but this was done after the wear levelling worker
detects the bitflip. So changes the initialisation of these two
tasks in u-boot.
This is a u-boot specific patch and not needed in the linux layer,
because due to commit 1b1f9a9d00
UBI: Ensure that "background thread" operations are really executed
we schedule these tasks in place and not as in linux after the inital
task which schedule this new task is finished.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In nand_davinci_readecc(), select the correct NANDF<n>ECC register based
on CONFIG_SYS_NAND_CS rather than hardcoding the choice of NANDF1ECC.
This allows 1-bit hardware ECC to work with chip select other than CS2.
Note this now matches the usage in nand_davinci_enable_hwecc(), which
already had the correct handling, and allows refactoring to a single
function encapsulating the register read.
Without this fix, writing NAND pages to a chip not wired to CS2 would
result in in the ECC calculation always returning FFFFFF for each
512-byte segment, and reading back a correctly written page (one with
ECC intact) would always fail. With this fix, the ECC is written and
verified correctly.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
If CONFIG_LBA48 is not defined, the element lba48 of struct sata_dev_desc
is not avaible, and can't be used.
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.
During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used. In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.
We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Teranetics PHY does not properly report the link state
for fiber connections. The new PHY code actually checked the link,
and so the FM driver would refuse to talk over a linkless PHY.
But the link may actually be up, so now we always report it as up
for fiber connections on the tn2020.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix:
ohci-hcd.c: In function 'dl_transfer_length':
ohci-hcd.c:968:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Fix:
smc91111.c: In function 'smc_phy_configure':
smc91111.c:1194:6: warning: variable 'failed' set but not used [-Wunused-but-set-variable]
smc91111.c:1190:7: warning: variable 'phyaddr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:225:6: warning: unused variable 'devices_found'
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
[-Wunused-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Esp. while printing the environment the output is usually longer than 512
bytes. Instead of cutting the message, send multiple 512 bytes packets.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These drivers have never been converted to NET_MULTI, and they are only
used by one board (BMW). So drop the drivers until someone feels like
rewriting them for NET_MULTI support.
Rather than punting the BMW board completely, just disable net support
in its board config. Seems to build fine without it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-nand-flash:
PPC: Fix socrates NAND problem
PPC: Fix fsl_upm.c by renaming nand handling functions
NAND: Make page, erase, oob size available via cmd_nand
mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
NAND: Add -y option to nand scrub command
NAND: Add nand read.raw and write.raw commands
NAND: Really ignore bad blocks when scrubbing
spl, nand: add 4bit HW ecc oob first nand_read_page function
mxc_nand: fix a problem writing more than 32MB
mxc_nand: fixed some typos (cosmetic)
nand: increase chip_delay in mv kirkwood nand driver
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
This avoids colision with nand subsystem's functions.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
v2: fix broken mailer
Signed-off-by: mhench <mhench@elutions.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: use chip instead of redundant priv_nand]
Signed-off-by: Scott Wood <scottwood@freescale.com>
When writing 0x4000 to the unlockend_blkaddr register, large writes to
a 2k page NAND sometimes fail. The current kernel driver writes 0xFFFF
to this register for V2 of the nand controller.
However on an i.MX31 this also fixes writes larger than 32MB.
The datasheet is very unspecific, but (0x4000=16384)*2000
roughly fits the limits we're encountering with NAND writes.
This problem might be NAND chip specific.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The new SAMSUNG NAND Flash K9F1G08U0D require a bigger chip_delay.
The Data Transfer from Cell to Register is >= 35us. Other Vendors
and older chips normally use >= 25us. To have enough margin 40us
is selected.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The SoC configuration may have more ports enabled than a given board
actually can utilize. Add a routinue that allows the board code to
disable a port that it knows isn't being used.
fm_disable_port() needs to be called before cpu_eth_init().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When enable the multi-bus, the current_bus is not inited in the original
implementation, which make the i2c operation unpredicatable.
Signed-off-by: Lei Wen <leiwen@marvell.com>
When DEBUG_I2C is open, the following build issue would shows up.
mv_i2c.c: In function 'i2c_transfer':
mv_i2c.c:257: error: 'ISR' undeclared (first use in this function)
mv_i2c.c:257: error: (Each undeclared identifier is reported only once
mv_i2c.c:257: error: for each function it appears in.)
Signed-off-by: Lei Wen <leiwen@marvell.com>
Current xilinx emaclite use net multi registration
but doesn't support several emaclites interfaces.
Changing driver name with adding address to name
is the first step how to distiguish several drivers.
Signed-off-by: Michal Simek <monstr@monstr.eu>
vmt.c: In function ‘ubi_free_volume’:
vmt.c:681:6: warning: variable ‘err’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
nand_bbt.c: In function ‘search_bbt’:
nand_bbt.c:465:6: warning: variable ‘bits’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
ipu_disp.c: In function ‘ipu_disp_set_global_alpha’:
ipu_disp.c:1237:11: warning: variable ‘flow’ set but not used
[-Wunused-but-set-variable]
ipu_disp.c: In function ‘ipu_disp_set_color_key’:
ipu_disp.c:1302:16: warning: variable ‘flow’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
If CONFIG_SYS_NS16550_MEM32 is defined then 32 bit memory
mapped access will be used to read/write the uart registers.
This is especially useful for SoC devices that implement 16550
compatible uarts but that have peripheral access width constraints.
Signed-off-by: Dave Aldridge <fovsoft@gmail.com>
Rewrite the mxc_i2c driver.
* This version is much closer to Linux implementation.
* Fixes IPG_PERCLK being incorrectly used as clock source
* Fixes behaviour of the driver on iMX51
* Clean up coding style a bit ;-)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linro.org>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Jason Liu <jason.hui@linro.org>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This patch allows user to register multiple FEC controllers. To preserve
compatibility with older boards, the mxcfec_register() call is still in place.
To use multiple controllers, new macro is in place, the mxcfec_register_multi(),
which takes more arguments. The syntax is:
mxcfec_register_multi(bd, FEC ID, FEC PHY ID on the MII bus, base address);
To disable the fecmxc_register() compatibility stuff, define the macro
CONFIG_FEC_MXC_MULTI. This will remove the requirement for defining IMX_FEC_BASE
and CONFIG_FEC_MXC_PHYADDR.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
The default is MII100, which was hardcoded previously in the driver.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This is cosmetic patch for the help message:
Before:
pmic dump [numregs] dump registers
After:
pmic dump [numregs] - dump registers
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Once the MDIO state machine has been initialized and enabled, it
starts polling all 32 PHY addresses on the MDIO bus, looking for
an active PHY. Add a 5 ms delay, so all PHYs are for sure detected.
This problem was detected on the cmc board with a KSZ8864 switch.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The PHY driver was too verbose and corrupted the boot message display
like this:
...
Net: Ethernet PHY: KSZ8873 @ 0x02
DaVinci-EMAC
...
Turn printf() into debug() so we get the expected output again:
...
Net: DaVinci-EMAC
...
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Paulraj Sandeep <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enable high capacity to host capability.
Fixes eMMC detection on boot from MMC/SD card.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for Fast Ethernet Controller driver for
Armada100 series.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds generic GPIO driver framework support for Marvell SoCs.
To enable GPIO driver define CONFIG_MARVELL_GPIO and for GPIO commands
define CONFIG_CMD_GPIO in your board configuration file.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND support (including spl) on IFC, such as is found on the p1010.
Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC. UBI should
work, as it does not use OOB for anything but ECC.
When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
- Use both getenv() and hwconfig to get USB phy type till getenv()
is depricated
- Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
has internal UTMI phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 041c542219.
The lines removed by this commit weren't redundant. The logic is (and
probably should be better commented):
Find the intersection of the advertised capabilities of both sides of
the link (lpa).
From that intersection, find the highest capability we can run at
(that will be the negotiated link).
Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL).
The code will now set phydev->speed to 100, and phydev->duplex to 1,
but this link does not support 100FULL.
Kudos to Andy Fleming <afleming@gmail.com> for binging this to
attention and for the explanation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
On some systems, we get a warning when %lu is used with size_t's, so
use the correct format string.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This allows the EEPROM layer to send a single i2c write command
per page, and wait CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS between
i2c write commands.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This change slightly improves readability of the phydev speed/duplex
assignment logic.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This change allows to cope with a mii bus device registered using
miiphy_register(), which doesn't assign a default reset handler.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Commit 6af1d41 "smc911x MII made available" was missing a few "const"
qualifiers. Fix the resulting in build warnings:
smc911x.c: In function 'smc911x_initialize':
smc911x.c:297: warning: passing argument 2 of 'miiphy_register' from incompatible pointer type
smc911x.c:297: warning: passing argument 3 of 'miiphy_register' from incompatible pointer type
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Helmut Raiger <helmut.raiger@hale.at>
The driver already had the MII functions, but they have not been
registered using miiphy_register().
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Fix build warning:
Configuring for jadecpu board...
mb86r0xgdc.c: In function 'dsp_init':
mb86r0xgdc.c:60: warning: unused variable 'i'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
The Lattice code was missed by commit e6a857d "fpga: constify to fix
build warning" resulting in such warnings:
fpga.c: In function 'fpga_load':
fpga.c:238: warning: passing argument 2 of 'lattice_load' discards qualifiers from pointer target type
fpga.c: In function 'fpga_dump':
fpga.c:278: warning: passing argument 2 of 'lattice_dump' discards qualifiers from pointer target type
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Stefano Babic <sbabic@denx.de>
The following commit:
commit de701d1183
Author: Syed Mohammed Khasim <khasim@ti.com>
Date: Tue Apr 19 14:00:34 2011 -0500
OMAP3: Add DSS driver for OMAP3
Added videomodes to the object list w/o any protection. This causes
build issues like:
videomodes.o:(.rodata.res_mode_init+0x0): multiple definition of `res_mode_init'
videomodes.o:(.rodata.res_mode_init+0x0): first defined here
videomodes.o: In function `video_get_params':
/local/home/galak/git/u-boot/drivers/video/videomodes.c:160: multiple definition of `video_get_params'
videomodes.o:/local/home/galak/git/u-boot/drivers/video/videomodes.c:160: first defined here
videomodes.o: In function `video_get_video_mode':
/local/home/galak/git/u-boot/drivers/video/videomodes.c:229: multiple definition of `video_get_video_mode'
videomodes.o:/local/home/galak/git/u-boot/drivers/video/videomodes.c:229: first defined here
videomodes.o:(.rodata.vesa_modes+0x0): multiple definition of `vesa_modes'
videomodes.o:(.rodata.vesa_modes+0x0): first defined here
make[1]: *** [libvideo.o] Error 1
Remove the unconditional inclusion and move to adding to
CONFIG_VIDEO_OMAP3 case.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mmc_send_status() function sets cmd.arg = 0. That's incorrect, so fix it.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Tested-by: Lei Wen <adrian.wenl@gmail.com>
With this, the EHCI seems to "recover" from a timeout. This is particularly
observable if you were to ping the wrong IP Address and then ping the correct
one or if there was a temporary failure during tftp sessions.
All it takes is one timeout to disable it. If you have a noisy network (lot
of traffic), even if the traffic is not for the board, the timeouts don't occur.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove __attribute__ ((packed)) to prevent byte access to soc
registers in some gcc versions.
Having patches to enable ehci for the BeagleBoard lying around for
several months, this one was the show-stopper.
Switched to align(4), rather than remove the attribute, per suggestion
from Alexander.
Credits have to go to Laine Walker-Avina <lwalkera@ieee.org> for
finding the problem.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Alexander Holler <holler@ahsoftware.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TX and RX channel numbers programmed as '1' during EMAC
teardown initialization is wrong. This patch fixes the
same by setting channel number to '0' which is used by U-boot.
Signed-off-by: Sugumar Natarajan <sugumar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Now that all platforms have been migrated to the new MMC driver, remove
the old one.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for software I2C for GONI and Universal C210 reference targets.
It adds support for access to GPIOs by number, not as it is present,
by bank and offset.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
IMX processors has a slightly different interface
to access GPIOs and do not make use of the provided GPIO
framework. The patch substitutes mxc_ specific
functions and make use of the API in asm/gpio.h
Signed-off-by: Stefano Babic <sbabic@denx.de>
This change is driven by need of general gpio_* functions,
which as their parameter are accepting the GPIO pin number, NOT
block and pin.
This makes the code alike to omap, and allows for using more
generic frameworks (e.g. software I2C).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Currently if a DMA buffer straddles a buffer alignment boundary
(512KiB) then the DMA engine will pause and generate a DMA
interrupt. Since the DMA interrupt is not enabled it will hang
the MMC driver.
This patch adds support for restarting the DMA transfer. The
SYSTEM_ADDRESS register contains the next address that would have
been read/written when a boundary is hit. So we can read that
and write it back. The write triggers the resumption of the
transfer.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tested-by : Jaehoon Chung <jh80.chung@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
The PHY driver was too verbose and corrupted the boot message display
like this:
...
Net: TSEC0 connected to Marvell 88E1111S
TSEC1 connected to Marvell 88E1111S
TSEC0, TSEC1
...
Turn printf() into debug() so we het the expected output again:
...
Net: TSEC0, TSEC1
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.
r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.
r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Built-in Ethernet adapters support setting the mac address by means of a
ethaddr environment variable for each interface (ethaddr, eth1addr, eth2addr).
This adds similar support to the USB network side, using the names
usbethaddr, usbeth1addr, etc. They are kept separate since we don't want
a USB device taking the MAC address of a built-in device or vice versa.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
The SMSC95XX is a USB hub with a built-in Ethernet adapter. This adds support
for this, using the USB host network framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The U-Boot Design Principles[1] clearly say:
Initialize devices only when they are needed within U-Boot, i.e. don't
initialize the Ethernet interface(s) unless U-Boot performs a download
over Ethernet; don't initialize any IDE or USB devices unless U-Boot
actually tries to load files from these, etc. (and don't forget to
shut down these devices after using them - otherwise nasty things may
happen when you try to boot your OS).
So, do not initialize and read the sensors on startup.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
* 'master' of git://git.denx.de/u-boot-arm:
drivers/rtc: add Marvell Integrated RTC
Armada100: Add Board Support for Marvell GuruPlug-Display
Armada100: MFP macro naming correction
arm: auto gen asm-offsets.h for mb86r0x
spear: fix build errors for spear3xx/spear600 platforms
cosmetic: arm: lib/board.c: Coding Style cleanup
ARM: versatile: fix board support
SMDKV310: Enable device tree support
SMDKV310: MMC_SPL: Fix building when using "make O="
arm: a320: enable tagged list support
arm: a320: fix multiline comment style
ARMv7: u8500_href: Add missing header to fix compiler warning
Removed unused define, CONFIG_ARMV7.
avr32: add grasshopper (ICnova AP7000) board
AT91/SPI: fix atmel_dataflash_spi.c to allow building without warnings
MAKEALL: remove AT91 boards that are in boards.cfg
AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/master
AT91: Board fix for AT91SAM9261-EK
AT91: SoC fix at91sam9261_matrix.h
AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/master
AT91: change common at91sam9261 files to compile with new scheme
AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)
a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USART
README: fix arm920t/at91 path
net/eth.c: drop obsolete at91rm9200 support
README.at91-soc: remove AT91(RM9200) joining notice
a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warning
MAKEALL: remove obsolete at91rm9200 soc
ARM: remove obsolete at91rm9200
omap4: clock init support for omap4460
omap4: support TPS programming
omap: reuse omap3 gpio support in omap4
omap4: sdram init changes for omap4460
omap4: add omap4460 revision detection
mkimage: Add OMAP boot image support
omap: add MMC and FAT support to SPL
omap: add basic SPL support
armv7: start.S: fixes and enhancements for SPL
omap4: automatic sdram detection
omap4: calculate EMIF register values
omap4: add sdram init support
omap4: add clock support
omap4: add OMAP4430 revision check
omap4: cleanup pin mux data
omap4: utility function to identify the context of hw init
DA8xx: fix LPSC constants
DA8xx: switch an enum to defines for consistency
DA8xx: add MMC/SD controller addresses
DaVinci EMAC: declare function for all DA8xx CPUs
DA8xx: add generic GPIO driver
DaVinci: rename gpio_defs.h to gpio.h
omap3evm: eth: Include functions only when necessary
omap3evm: Update ethernet reset sequence for Rev.G board
omap3evm: eth: split function setup_net_chip
omap3: Include array definition only when it is used
omap730p2: fix build breaks
omap2420h4: fix build breaks
omap1610inn: fix build breaks
omap1510inn: fix build breaks
omap5912osk: fix build breaks
omap1610h2: fix build breaks
Add detection of Coral-PA and configure Coral CCF an MMR parameters
using CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx_MMR macros.
Use CCF and MMR parameters for Coral-P Eval. Board if the appropriate
macros weren't defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
This driver can be used for kirkwood SoCs by enabling CONFIG_RTC_MV. Tested on
Global Scale Technologies Dreamplug.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Add a generic GPIO driver for the DaVinci DA8xx processors. It is turned
on by defining CONFIG_DA8XX_GPIO and fulfills the generic GPIO interface
specified in <asm/gpio.h> . The driver has support for both manipulating
GPIO pins as well as automatically configuring the pin multiplexor
registers to set the pin function to GPIO.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
There is a optimized version of memset in u-boot available so use it instead
of the hand written loop version.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Add support of MX25L4005 and MX25L8005 according to the datasheet
http://www.mct.net/download/macronix/mx25l8005.pdf
This patch has been tested with MX25L4005 and MX25L8005
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Fix compiler warning:
cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type
Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre Schwarz<andre.schwarz@matrix-vision.de>
Fix the following:
ERROR: do not initialise statics to 0 or NULL
ERROR: do not use assignment in if condition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Run cfb_console.c through indent and manually fix some of he
deficiencies of the automatic line breaking.
Fix multiline comments, excessive line spacing and such.
No changes to code done.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 09c2e90c11 "unify version_string"
introduced a build breakage in cfb_console.c
---8<---
cfb_console.c:1497: warning: format '%s' expects type 'char *', but
argument 3 has type 'const char (*)[]'
--->8---
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
This reverts commit c310fc8404.
The Atmel custodian had apparently rejected this patch's approach in
another thread, so this patch reverts it for now.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Only install der 4xx-EMAC interrupt handlers *after* the core
network driver is registered.
This problem was noticed on the APM Taishan 440GX board, where
the board hung upon bootup after displaying "Net:".
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the architecture specific implementation of
version_string where possible. Some architectures use a special place
and therefore we provide U_BOOT_VERSION_STRING definition and a common
weak symbol version_string.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Peter Pan <pppeterpppan@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
gen10g_startup() had 2 bugs:
1) It had a boolean logic error in checking the MMD mask, and
always checked all of them.
2) It checked devices which don't actually report link state, which
meant that it would never believe the link was fully up.
Fix the boolean logic, and then mask the MMD mask so only link-reporting
devices are checked.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reported-by: Ed Swarthout <Ed.Swarthout@freescale.com>
The multi serial support has a "ctlr" field which almost no one uses,
but everyone is forced to set to useless strings. So punt it.
Funny enough, the only code that actually reads this field (the mpc8xx
driver) has a typo where it meant to look for the SCC driver. Fix it
while converting the check to use the name field.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Rather than sticking arch/board/driver specific logic in the common
serial code, push it all out to the respective drivers. The serial
drivers declare these funcs weak so that boards can still override
things with their own definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
Newer SST flashes have dropped the Auto Address Increment (AAI) word
programming (WP) modes in favor of the standard page programming mode
that most flashes now support. So add a flags field to the different
flashes to support both modes with new and old styles.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
