For LS1, esdhc is big-endian IP. Accessing the registers
should be in big-endian mode. So we use esdhc_read32()
to read Host controller capabilities register for LS1.
For LS1, when using CMD12, cmdtype need to be set to
ABORT, otherwise, next read command will hang.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO. Only define this function
in this case as well.
Signed-off-by: Tom Rini <trini@ti.com>
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.
Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The controller reset is performed now if command error occurs.
This commit adds the reset for the case of data related errors too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Calculation of the timeout value should be based on actual clock value,
written to controller registers. Since mmc->tran_speed is either the
maximum allowed speed, or the preliminary value, that is be not yet
set to registers, the actual timeout, taken by the controller, based
on its clock settings, may be much longer than expected, based on
mmc->tran_speed value. In particular it happens at early initialization
stage, when typical value of mmc->tran_speed is 20MHz or 26MHz, while
actual clock setting, configured in the controller, is 400kHz.
It's more correct to use mmc->clock value for timeout calculation instead.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Using an array is pointless; even more pointless (and scary) is using
sprintf to fill it without a format string.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Remove the in-structure ops and put them in mmc_ops with
a constant pointer to it.
This makes the mmc structure smaller as well as conserving
code space (in theory).
All in-tree drivers are converted as well; this is done in a
single patch in order to not break git bisect.
Changes since V1:
Fix compilation b0rked issue on omap platforms where OMAP_GPIO was
not set.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.
This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.
Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.
Test on P5040 and T4240,
Error Log:
=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
eSDHC host controller has new register to support SD Spec 3.0.
And the according host controller version was Freescale eSDHC
Version 3.0.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:
Commit 7b43db9211
drivers/mmc/fsl_esdhc.c: fix compiler warnings
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The cache should invalidate the read buffer for
the SD card interface after the transfer complete,
not command-complete.
Tested-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.
It is tested with a MMCplus card.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
All esdhc variants we know should support high capacity MMC cards,
so let's add MMC_MODE_HC host_caps unconditionally to support those
MMC cards (capacity > 2 GB).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
fsl_esdhc.c:71:6: warning: symbol 'esdhc_xfertyp' was not declared. Should it be static?
fsl_esdhc.c:413:6: warning: symbol 'set_sysctl' was not declared. Should it be st
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
The cache snooping feature of Freescale's eSDHC IP is not available on i.MX, so
disable it globally for this architecture. This avoids setting no_snoop for all
i.MX boards, and it prevents setting a reserved bit of a reserved register if
fsl_esdhc_mmc_init() is used on i.MX, like in
arch/arm/cpu/armv7/imx-common/cpu.c/cpu_mmc_init().
Since no_snoop was only used on i.MX, get rid of it BTW.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
For FSL low-end processors (VVN2.2), in order to detect the SD card,
we should enable PEREN, HCKEN and IPGEN to enable the clock.
Otherwise, after booting the u-boot, and then inserting the SD card,
the SD card can't be detected.
For SDHC VVN2.3 IP, these bits are reserved, and SDCLKEN is used.
And when accessing to these reserved bit, no any impact happened.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch imports parts of two patches from the Freescale U-Boot with the following
commit messages:
ENGR00156405 ESDHC: Add workaround for auto-clock gate errata ENGcm03648
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=e436525a70fe47623d346bc7d9f08f12ff8ad787
The errata, not applicable to USDHC, causes ESDHC to shut off clock to the card
when auto-clock gating is enabled for commands with busy signalling and no data
phase. The card might require the clock to exit the busy state, so the workaround
is to disable the auto-clock gate bits in SYSCTL register for such commands. The
workaround also entails polling on DAT0 bit in the PRSSTAT register to learn when
busy state is complete. Auto-clock gating is re-enabled at the end of busy state.
ENGR00156670-1 ESDHC/USDHC: Remove delay before each cmd and some bug fixes
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=a77c6fec8596891be96b2cdbc742c9824844b92a
Removed delay of 10 ms before each command. There should not be a need to have this
delay after the ENGR00156405 patch that polls until card is not busy anymore before
proceeding to next cmd.
This patch imports the polling part of both patches. The auto-clock gating code
don't apply for i.MX6 as implemented in these two patches.
SYSCTL_RSTA was defined twice. Remove one definition.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
The pointer to the registers used to control the Freescale ESDHC MMC
controller is not initialized correctly when using PIO mode. This is
fixed by initializing the pointer in the same way as all other sites
within the driver.
Examining the commit history shows that this was broken at introduction
due to a code change in upstream U-Boot to support the mx51 processor
family.
Reported-by: Jim Lentz <JLentz@zhone.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
This card-detect hook probably doesn't work. Perhaps somebody with more
knowledge about the hardware can comment on this. I think that perhaps
even the complete code from esdhc_init() could go into the getcd()
function instead or mmc_getcd() needs to be called at some later time
after mmc_init(), which, however, would require many other drivers to
change.
In addition to implementing the hook, this patch also removes the call
to the board_mmc_getcd() function which is now called from the MMC
framework and is no longer required here.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
The new API no longer uses the extra cd parameter that was used to store
the card presence state. Instead, this information is returned via the
function's return value. board_mmc_getcd() returns -1 to indicate that
no card-detection mechanism is implemented; 0 indicates that no card is
present and 1 is returned if it was detected that a card is present.
The rationale for this change can be found in the following email
thread:
http://lists.denx.de/pipermail/u-boot/2011-November/110180.html
In summary, the old API was not consistent with the rest of the MMC API
which always passes a struct mmc as the first parameter. Furthermore the
cd parameter was used to mean "card absence" in some implementations and
"card presence" in others.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
The mmc host controller on the i.mx6q is called usdhc which
is redesigned based on the freescale esdhc controller.
The usdhc controller is almost compatible with esdhc except
it adds one mix register to support debug/SD3.0 and move
the low bit 0-6 of XFERTYP register to the mix control reg
low bit 0-6. Thus on i.mx6q, we have the following compared
with the previous soc: (can refer to RM of chapter 56.3.3)
i.mx6q:
mix control:
bit 31 - bit 7: Added for debug/SD3.0 support
bit 6 - bit 0: move in the XFERTYP register bit 6-0 on previous soc
XFERTYP register:
bit 31 - bit 7: the same as before,
bit 6 - bit 0: no-use
previous soc
mix control: no
XFERTYP register:
bit 31 - bit 0: xfertype information
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.
This is a software Software Restrictions in i.MX53 reference manual:
29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout. It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error
would yield the first error return instead of TIMEOUT.
By swapping the test TIMEOUTs are reported as such
An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define
but as that one might be less desired I've opted for the simplest solution
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:
9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Timeout counter value is set as DTOCV bits in SYSCTL register
For counter value set as timeout,
Timeout period = (2^(timeout + 13)) SD Clock cycles
- As per 4.6.2.2 section of SD Card specification v2.00, host should
cofigure timeout period value to minimum 0.25 sec.
- Number of SD Clock cycles for 0.25sec should be minimum
(SD Clock/sec * 0.25 sec) SD Clock cycles
= (mmc->tran_speed * 1/4) SD Clock cycles
- Calculating timeout based on
(2^(timeout + 13)) >= mmc->tran_speed * 1/4
Taking log2 both the sides and rounding up to next power of 2
=> timeout + 13 = log2(mmc->tran_speed/4) + 1
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.
Clear these bits out when we read HOSTCAPBLT.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some new platform's esdhc pins don't share with other function.
The eSDHC shouldn't be disabled, even if "esdhc" isn't defined
in hwconfig env variable.
Use CONFIG_FSL_ESDHC_PIN_MUX to fix this problem.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
