eth-uclass.c expects DM-capable Ethernet adapters to implement ops->
read_rom_hwaddr(), or for some other mechanism to set pdata->enetaddr, or
for the user to set environment variable $usbethaddr. Without any of
these, it will refuse to initialize the device since no valid MAC address
is known. Implement this function for the smsc95xx driver.
With this feature implemented, there is no point smsc95xx_init_common()
re-reading the MAC address from ROM, so ifdef out this code when DM_ETH
is enabled.
This allows (at least) the built-in Ethernet on the NVIDIA Harmony board
to operate again.
Fixes: 0990fcb772 ("net: smsc95xx: Add driver-model support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The call to flush cache on the transmit buffer was misplaced (for very
short packets) and asked to flush less than a cacheline.
Move the flush cache call to after a short packet has been padded
to minimum length (so the padding is flushed too), and round the size
up to a cacheline.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards these switches are wired directly into a SERDES
interface on another Ethernet MAC. Add the ability to specify
these kinds of boards using CONFIG_MV88E61XX_FIXED_PORTS which defines
a bit mask of these fixed ports.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Marvell Link Street mv88e60xx is a series of FastEthernet switch
chips, some of which also support Gigabit ports. It is similar to the
mv88e61xx series which support Gigabit on all ports.
The main difference is the number of ports. Which affects the
PORT_COUNT define and the size of the mask passed to
mv88e61xx_port_set_vlan().
Other than that it's just a matter of adding the appropriate chip
IDs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Cc: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
cpsw driver supports only selection of phy mode in control module
but control module has more setting like RGMII ID mode selection,
RMII clock source selection. So ported to cpsw-phy-sel driver
from kernel to u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In the current driver implementation, config() callback is common
for AR8035 and AR8031 phy. In config() callback, driver tries to
configure MMD Access Control Register and MMD Access Address Data
Register unconditionally for both phy versions which leads to
auto negotiation failure in AM335x EVMsk second port which uses
AR8031 Giga bit RGMII phy. Fixing this by adding separate config
for AR8031 phy.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This adds support for internal delay on RX and TX on RGMII interface for the
AR8035 phy.
This is basically the same Linux driver do. Tested on a Zynq Zturn board (for
which u-boot support in is my tree; first patch waiting ML approval)
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that all x86 boards have been converted to DM video, drop the
legacy drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With DM VESA driver on x86 boards, plat->base/size/align are all
zeroes and starting address passed to alloc_fb() happens to be 1MB
aligned, so this routine does not trigger any issue. On QEMU with
U-Boot as coreboot payload, the starting address is within 1MB
range (eg: 0x7fb0000), thus causes failure in video_post_bind().
Actually if plat->size is zero, it makes no sense to do anything
in this routine. Add such check there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present only chromebook boards are converted to DM video. Other
x86 boards are still using the legacy cfb_console driver. This
switches to use DM version drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With DM conversion, information like "Video: 1024x768x16" is not
shown anymore. Now add these verbose output back.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage
enable/disable functions for lp873x family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage
enable/disable functions for palmas family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write funtions to access pmic
registers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for gpio regulators. As of now this driver caters
to gpio regulators with one gpio. Supports setting voltage values to gpio
regulators and retrieving the values.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These two options go together and it is best to do the conversion in one
step. So enable DM_MMC_OPS by default if DM_MMC is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
This gives a build warning on 64-bit x86. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should consistently use %z with size_t, and avoid passing a uint32_t as
a size_t value. Fix these issues to avoid warnings on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For 64-bit x86, __I386__ should perhaps not be defined. It is not clear from
the definition, but let's use CONFIG_X86 to be sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the samus driver to avoid the direct call to the video BIOS setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we use the legacy vesa driver for graphics. Add a driver which
supports driver model. This can be probed only when needed, removing the
need to start up the display if it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide a function to run the Vesa BIOS for a given PCI device and obtain
the resulting configuration (e.g. display size) for use by the video
uclass. This makes it easier to write a video driver that uses vesa and
supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful in debug() statements to display the name of the uclass for a
device. Add a simple function to provide this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This makes the assumption that setting up pinctrl in cpu_init_r() is safe.
On samus we need GPIOs before relocation in order to support power control.
This commit fixes the following message on boot:
initcall sequence ffe5c6f4 failed at call ffe01d3d (err=-1)
### ERROR ### Please RESET the board ###
In any case it seems better to leave init to driver model, so that it can
pick up the GPIO driver when it needs it. Since pinctrl is a dependency of
the GPIO driver, we may as well put the dependency there and avoid these
problems.
This reverts commit 9769e05bcf.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
According to the binding documentation the fixed regulator enable GPIO
is optional. However so far registration thereof failed if no enable
GPIO was specified. Fix this by making it entirely optional whether an
enable GPIO is used.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use the generic error number instead of meaningless value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
"host->version" isn't a SoC specific value.
It doesn't need to get in each SoC drivers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Some arguments don't need to pass to dwmci_setup_cfg.
They are already included in dwmci_host structure.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch support the driver model for s5p_sdhci controller.
To support the legacy model, maintained the existing code.
Note: If use the Driver Model, it needs to modify the device-tree.
In future, will update the Device-tree and enable the configuratioin.
(CONFIG_BLK, CONFIG_DM_MMC and CONFING_DM_MMC_OPS)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
