Alexey:
1. Significantly rework cache-related functionality.
In particular that fixes coherency problems in some corner-cases,
allows us to enable and disable caches in run-time and still
have properly running system, finally support execution from
real flash (before we used to run from DDR from the very beginning).
2. Remove string routines implemented in assembly.
That allows us to build and run U-Boot on wide range of ARC cores
with different configurations. I.e. whatever tuning is used on GCC's
command-line we'll get code for desired flavor of ARC.
Otherwise for each and every corner-case we would need to add ifdefs
in assembly code to accommodate missing instructions etc.
3. Get use of GCC's garbage collector which helps to slim-down resulting image
quite a bit.
4. Also now we may disable U-Boot self-relocation for ARC if needed either
by platform or for debugging purposes.
Refactor GO and PREP subcommands implementation for a simpler
override in the boards platform code.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As of now newer pmufw is keeping old interfaces. That's why permit
u-boot to run on newer version. Recommended version will be setup later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync dts from Linux 4.16 and also add u-boot specific
dtsi for OMAPl138 board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 6aa4ad8e38 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
converted SOC_DA8XX to Kconfig but missed enabling DDR_INIT for
SOC_DA8XX, which broke OMAPL138 to boot.
Commit 2e87980580 ("davinci: Fix omapl138_lcdk builds") disabled
DDR_INIT for all DA850 SoCs. This failed all DA850 boards to boot
as ddr is not being initialized.
Enable SYS_DA850_DDR_INIT for DA8XX so that all DA850 and OMAPL138
will have ddr initialized
Fixes: 2e87980580 ("davinci: Fix omapl138_lcdk builds")
Fixes: 6aa4ad8e38 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable all types of non-secure access to PFE block registers.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces
to bufferable.
2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces.
3. Disable ECC detection for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SoC specific PFE macros are defined and structure ccsr_scfg
is updated with members defined for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Layerscape Gen2 SoC supports GPIO registers to control GPIO
signals. Adding support of GPIO structure to access GPIO
registers.
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move all checks before cache flush and IOC setup.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add missing cache cleanup before cache disable:
* Flush and invalidate L1 D$ before disabling. Flush and invalidate
SLC before L1 D$ disabling (as it will be bypassed for data)
Otherwise we can lose some data when we disable L1 D$ if this data
isn't flushed to next level cache. Or we can get wrong data if L1 D$
has some entries after enable which we modified when the L1 D$ was
disabled.
* Invalidate L1 I$ before disabling. Otherwise we can execute wrong
instructions after L1 I$ enable if we modified any code when
L1 I$ was disabled.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add additional cache configuration checks and note about
supported configurations.
It is unlikely to face some configuration in real life but
it's better to be prepared and refuse to work on those.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Implement specialized function to clenup caches (and therefore
sync instruction and data caches) which can be used for cleanup before linux
launch or to sync caches during U-Boot self-relocation.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
If L1 D$ is disabled SLC is bypassed for data and all
load/store requests are sent directly to main memory.
If L1 I$ is disabled SLC is NOT bypassed for instructions
and all instruction requests are fetched through SLC.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Implement icache_enabled() and dcache_enabled() as separate functions
which can be used with "inline" attribute. This is a preparation to
make them always_inline.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Move check for PAE existence into slc_upper_region_init()
instead of its caller as more appropriate place.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There is a problem with current implementation if we start U-Boot
from ROM, as we use global variables before ther initialization,
so these variables get overwritten when we copy .data section
from ROM.
Instead we move these global variables into our "global data"
structure so that we may really start from ROM.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There is a problem with current implementation if we start U-Boot
from ROM, as we use global variables before ther initialization,
so these variables get overwritten when we copy .data section
from ROM.
Instead we'll use icache_exists(), dcache_exists(), slc_exists(), pae_exists()
functions which directly check BCRs every time.
In U-Boot case ops are used only during self-relocation and DMA
so we shouldn't be hit by noticeable performance degradation.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As of today we check SLC status before each call of __slc_rgn_op()
or __slc_entire_op(). So move status check into __slc_rgn_op()
and __slc_entire_op().
As we need to check status before *each* function execution and we
call slc_entire_op() and slc_rgn_op() from different places we add
this check directly into SLC entire/line functions instead of
their callers to avoid code duplication.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Use is_isa_arcv2() function where it is possible instead of
CONFIG_ISA_ARCV2 define check to make code cleaner at the same time
keeping pretty much the same functionality - code in branches
under "if (is_isa_arcv2())" won't be compiled if CONFIG_ISA_ARCV2
is not defined, still we need a couple of CONFIG_ISA_ARCV2
ifdefs to make compiler happy. That's because code in
!is_isa_x() branch gets compiled and only then gets optimized
away.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As we are planning to get rid of dozens of ifdef's in cache.c we
would better check D$ status before each entire/line operation
then check CONFIG_SYS_DCACHE_OFF config option.
This makes the code cleaner as well as D$ entire/line functions
remain functional even if we enable or disable D$ in run-time.
As we need to check status before *each* function execution and we
call D$ entire/line functions from different places we add
this check directly into D$ entire/line functions instead of
their callers to avoid code duplication.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We're starting to use more and more BCRs and having their
definitions in-lined in sources becomes a bit annoying
so we move it all to a separate header.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Move IOC initialization from cache_init() to a separate function.
This is the preparation for the next patch where we'll switch
to is_isa_arcv2() function usage instead of "CONFIG_ISA_ARCV2"
ifdef.
Also it makes cache_init function a bit cleaner.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't implement separate flush_dcache_all() intentionally as
entire data cache invalidation is dangerous operation even if we flush
data cache right before invalidation.
There is the real example:
We may get stuck in the following code if we store any context (like
BLINK register) on stack in invalidate_dcache_all() function.
BLINK register is the register where return address is automatically saved
when we do function call with instructions like 'bl'.
void flush_dcache_all() {
__dc_entire_op(OP_FLUSH);
// Other code //
}
void invalidate_dcache_all() {
__dc_entire_op(OP_INV);
// Other code //
}
void foo(void) {
flush_dcache_all();
invalidate_dcache_all();
}
Now let's see what really happens during that code execution:
foo()
|->> call flush_dcache_all
[return address is saved to BLINK register]
[push BLINK] (save to stack) ![point 1]
|->> call __dc_entire_op(OP_FLUSH)
[return address is saved to BLINK register]
[flush L1 D$]
return [jump to BLINK]
<<------
[other flush_dcache_all code]
[pop BLINK] (get from stack)
return [jump to BLINK]
<<------
|->> call invalidate_dcache_all
[return address is saved to BLINK register]
[push BLINK] (save to stack) ![point 2]
|->> call __dc_entire_op(OP_FLUSH)
[return address is saved to BLINK register]
[invalidate L1 D$] ![point 3]
// Oops!!!
// We lose return address from invalidate_dcache_all function:
// we save it to stack and invalidate L1 D$ after that!
return [jump to BLINK]
<<------
[other invalidate_dcache_all code]
[pop BLINK] (get from stack)
// we don't have this data in L1 dcache as we invalidated it in [point 3]
// so we get it from next memory level (for example DDR memory)
// but in the memory we have value which we save in [point 1], which
// is return address from flush_dcache_all function (instead of
// address from current invalidate_dcache_all function which we
// saved in [point 2] !)
return [jump to BLINK]
<<------
// As BLINK points to invalidate_dcache_all, we call it again and
// loop forever.
Fortunately we may do flush and invalidation of D$ with a single one
instruction which automatically mitigates a situation described above.
And because invalidate_dcache_all() isn't used in common U-Boot code we
implement "flush and invalidate dcache all" instead.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Introduce is_isa_arcv2() and is_isa_arcompact() functions.
These functions only check configuration options and return
compile-time constant so they can be used instead of #ifdef's to
to write cleaner code.
Now we can write:
-------------->8---------------
if (is_isa_arcv2())
ioc_configure();
-------------->8---------------
instead of:
-------------->8---------------
ifdef CONFIG_ISA_ARCV2
ioc_configure();
endif
-------------->8---------------
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
