At present the interrupt does not work and the SPI bus runs much less
quickly than it should. Add settings to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present early clock init happens in SPL. If SPL did not run (because
for example U-Boot is chain-loaded from another boot loader) then the
clocks are not set as U-Boot expects.
Add a function to detect this and call the early clock init in U-Boot
proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file does not report a few possible errors and one message is missing
a newline. Fix these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If CONFIG_ARMV7_LPAE is not defined we should make sure that the feature
is disabled. This can happen if U-Boot is chain-loaded from another boot
loader which does enable LPAE.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if CONFIG_ARMV7_LPAE is defined then mmu_setup() will use
instructions which are invalid on ARMv4T. This happens on Tegra since it
has an ARMv4T boot CPU. Add a check for the architecture version to allow
the code to be built. It will not actually be executed by the boot CPU,
but needs to compile.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option allows skipping the call to lowlevel() while still performing
CP15 init. Support this on ARM720T so it can be used with Tegra.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename command ls to fsls as its conflicting with
generic file systesm command ls and this is causing
compilation failure as below, if both are enabled
and this patch fixes it.
cmd/jffs2.o:(.u_boot_list_2_cmd_2_ls+0x0):
multiple definition of `_u_boot_list_2_cmd_2_ls'
cmd/fs.o:(.u_boot_list_2_cmd_2_ls+0x0):first defined here
scripts/Makefile.build:359: recipe for target 'cmd/built-in.o'
failed
make[1]: *** [cmd/built-in.o] Error 1
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is some inconsistency between uses of CONFIG_RTC_DS13xx and
CONFIG_SYS_RTC_DS13xx. Address this by dropping the "SYS" from
these variables.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
With overrun enabled, serial port console freezes & stops receiving data with
overun error if we keep sending data.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Enable support for XIP (execute in place) of U-Boot or kernel image. There is
no need to copy image from flash to ram if flash supports execute in place.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Alexandru Gagniuc <alex.g@adaptrum.com>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
Documents the externally visible functions shared between the VOP
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documents the externally visible functions shared between the HDMI
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the warning,
---8<---
CACHE: Misaligned operation at range [3fdffff0, 3fdffffc]
---<8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend DE2 driver with support for TVE driver, which will be added in
next commit. TVE unit expects data to be in YUV format, so CSC support
is also added here.
Note that HDMI driver has higher priority, so TV out is not probed if
HDMI monitor is detected.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds TVE base address for Allwinner H3 and H5 SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to avoid future confusion with similary named files, rename
tve.c to tve_common.c. New name better represents the fact that this file
holds code which can be and will be shared between multiple drivers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit fixes the warning produced by gcc 7.1.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The addresses of the registers in TI TPS65217 are not continuous.
There is a gap between ENABLE(0x16) and DEFUVLO(0x18). No 0x17
register available.
Fixup the enum values by adding a 'reserved' placeholder to correct
the addresses higher than 0x17.
Series-to: Heiko Schocher <hs@denx.de>
Signed-off-by: Brock Zheng Techyauld Ltd <yzheng@techyauld.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The driver provides regulator set/get voltage
enable/disable functions for lp87565 family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support to bind the regulators/child nodes with the pmic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
We do not need to probe the block device here, so avoid doing so. The MMC
device itself must be active, but the block device can come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make sure that we probe the block device before using it when reading
the environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Many devices support a child block device (e.g. MMC, USB). Add a
convenient way to get this device given the parent device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add ddr voltage rail (dcdc3) configuration. Set the dcdc3
DDR supply to 1.35V.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Some boards like am437x-gp-evm require dcdc3 also to be configured
as it feeds on to ddr. Hence add the capability as well.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The Kconfig entry depends on RMOBILE, but this was renamed
to ARCH_RMOBILE in commit 1cc95f6e1b (ARM: Rmobile: Rename
CONFIG_RMOBILE to CONFIG_ARCH_RMOBILE) . Fix this omission.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
R-Car Gen3 series have four SD card interfaces (SDHI0 to SDHI3),
two of which can also be used as MMC interfaces (SDHI2 and SDHI3).
This adds High-speed mode SD clock frequency between 25MHz and 50MHz,
8bit/4bit bus width, high capacity and low voltage device support.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The existing test (patman --test) only covers basic checkpatch output.
We have had some problems with unicode processing and could use test
coverage for the various tags patman supports.
Add a new functional test which runs most of the patman flow on a few
test commits and checks that the results are correct.
See the documentation in the test for a description of what it does.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is not a good variable name in Python because 'list' is a type. It
shows up highlighted in some editors. Rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Allow the add_maintainers parameter to be a list of maintainers, thus
allowing us to simulate calling the script in tests without actually
needing it to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add some unicode to the test patches to make sure that patman does the
right thing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There is no need for this function to return the same object that was
passed in. Drop the return value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Unicode characters may appear in input patches so we should not warn about
them. Drop this warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is not a good variable name in Python because 'str' is a type. It
shows up highlighted in some editors. Rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The communication filter reads data in blocks and converts each block to
unicode (if necessary) one at a time. In the unlikely event that a unicode
character in the input spans a block this will not work. We get an error
like:
UnicodeDecodeError: 'utf8' codec can't decode bytes in position 1022-1023:
unexpected end of data
There is no need to change the input to unicode, so the easiest fix is to
drop this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Don't mess with the email address when outputting them. Just make sure
they are encoded with utf-8.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change encodes the CC list to UTF-8 to avoid failures on
maintainer-addresses that include non-ASCII characters (observed on
Debian 7.11 with Python 2.7.3).
Without this, I get the following failure:
Traceback (most recent call last):
File "tools/patman/patman", line 159, in <module>
options.add_maintainers)
File "[snip]/u-boot/tools/patman/series.py", line 234, in MakeCcFile
print(commit.patch, ', '.join(set(list)), file=fd)
UnicodeEncodeError: 'ascii' codec can't encode character u'\xfc' in position 81: ordinal not in range(128)
from Heiko's email address:
[..., u'"Heiko St\xfcbner" <heiko@sntech.de>', ...]
While with this change added this encodes to:
"=?UTF-8?q?Heiko=20St=C3=BCbner?= <heiko@sntech.de>"
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In the case where a new build only decreases sizes and does not increase
any size we still want to report what functions have been dropped when
doing a bloat comparison.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In os_dirent_get_typename() we are checking that type falls within the
known values of the enum os_dirent_t. With clang-3.8 testing this value
as being >= 0 results in a warning as it will always be true. This
assumes of course that we are only given valid data. Given that we want
to sanity check the input, we change this to check that it falls within
the range of the first to the last entry in the given enum.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay in thumb
mode.
At present, it is applied only for raw U-Boot. This patch moves it to just
before booting next image. This way armv7m will be in thumb mode for any image
like raw or image with header like zImage or standard U-Boot.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
