This patch changes a little bit the environment, current environment was broken
for a long time, and board don't as expected sometimes, on production systems
this is fixed adding boot script. I think it's time to change this to make a
system conformant environment and use generic distro configurations and
environment instead. We can use a boot script for the old way boot mode.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This allows transferring data directly to/from RAM. For example, one
could create a boot script that starts DFU on a RAM region, then once
DFU exits (which is under the control of the attached USB host, via a
USB bus reset), uses the code/data that was received over DFU.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Writing to files is a useful feature in general, so enable it everywhere.
The primary purpose is to make DFU useful on filesystems in addition to
raw devices.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
CONFIG_SYS_DFU_DATA_BUF_SIZE defines the size of chunks transferred
across USB. This doesn't need to be particularly large, since it doesn't
limit the overall transfer size.
CONFIG_SYS_DFU_MAX_FILE_SIZE is used to buffer an entire file before
writing it to a filesystem. This define limits the maximum file size that
may be transferred. Bump this up to 32MiB in order to support large
uncompressed kernel images.
Both of these buffers are dynamically allocated, and so the size of both
needs to be taken into account when calculating the required malloc
region size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 52a7c98a17 "tegra-common: increase malloc pool len by dfu mmc
file buffer size" updated the definition of CONFIG_SYS_MALLOC_LEN for
Tegra to take account of the DFU buffer size. However, this change had
no effect, since typical Tegra board config headers don't set the DFU-
related defines until after tegra-common.h is included. Fix this by
moving the affected conditional code to tegra-common-post.h, which is
included last. Also move the definition of SYS_NONCACHED_MEMORY since
it's a related and adjacent definition.
Fix the condition to test for the DFU feature, rather than specifically
MMC DFU support, so it applies in all cases.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable dwc3, dwc3-omap and PHY to get DWC3 functional in OMAP5
uEVM. Also enable support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
To reduce the size of the U-Boot image on the x600 board, lets enable
the THUMB mode. This reduces the overall size to less than 0x6000
bytes. Fitting it again in the onboard NOR flash.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
This board is equipped with a Micron NAND chip (MT29F1G08ABADAH4) that
needs 4-bit ECC. But the SPEAr600 only supports 1-bit HW ECC internally.
This patch enables the SW 4-bit BCH support for this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove dm355evm, dm355leopard, dm365evm, dm6467evm, dvevm, ea20, schmoogie,
sffsdr, sonata.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to generic board by the deadline.
Remove all cpu9260 and cpuat91 boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Linux kernel can enumerate mmc sd as either mmcblk0 or mmcblk1.
But u-boot default environment assumes that sd always populates
as mmcblk0. With this the root fs is not being mounted when
mmc sd is enumerated as mmcblk1.
So use partuuid to update root= option in default environment.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Define default mmc args in ti_armv7_common.h so that all
TI platforms can reuse.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
All TI SoCs expect filesystem to be ext4, omap4_common is the only one
with ext3. move omap4 to ext4 so that we can start consolidating MMC
arguments.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To simplify and having a common default IP-setup on all B&R boards we
introduce an environment variable "brdefaultip" which does following.
Test if ${ipaddr} is empty, if yes it set's up some defaults:
- ipaddr : 192.168.60.1
- netmask : 255.255.255.0
- gatewayip: 192.168.60.254
- serverip : 192.168.60.254
This environment is ran from CONFIG_PREBOOT.
All other "tricks" are dropped.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[root@pollux dfu-util]# ./src/dfu-util -l
dfu-util 0.8
Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc.
Copyright 2010-2014 Tormod Volden and Stefan Schmidt
This program is Free Software and has ABSOLUTELY NO WARRANTY
Please report bugs to dfu-util@lists.gnumonks.org
Found DFU: [0908:02d2] ver=0212, devnum=119, cfg=1, intf=0, alt=0, name="Linux", serial="UNKNOWN"
[root@pollux dfu-util]#
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>