When both CONFIG_USB_GADGET & CONFIG_USB_ETHER are defined
the makefile links objects twice.
This patch uses a Makefile specific idiom of
'if defined(CONFIG_USB_GADGET) || defined(CONFIG_USB_ETHER)'
to handle the case.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Dealing with raw block numbers with the dfu is very annoying.
Introduce a partition method.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Zero out timeout value; letting it filled with undefined values
ends up with the dfu host hanging.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
On EHCI controller with 64-bit address space support, we must initialize
properly the high word for the PCI bus master accesses.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of hardcoding the PCI IDs on the USB controller, use the PCI
class to detect them.
Ensure the busmaster bit is properly set in the PCI configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
This cast does not seem correct, since we should be writing to a pointer,
not a ulong.
This fixes the following warning on nds32:
-ns16550.c:49: warning: passing argument 2 of 'writeb' makes pointer from integer without a cast
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch corrects the following issues
1) Write the correct M/T Stop value to I2CSTAT after i2c write.
According to the spec, after finish the data transmission, we should
write a M/T Stop (I2C_MODE_MT | I2C_TXRX_ENA) to I2CSTAT instead of
a M/R Stop (I2C_MODE_MR | I2C_TXRX_ENA).
2) Not split the write to I2CSTAT into 2 steps in i2c read.
According to the spec, we should write the combined M/R Start value to
I2CSTAT after setting the slave address to I2CDS
3) Fix the mistake of making an equality check to an assignment.
In the case of I2C write with the zero-length address, while tranfering the
data, it should be an equality check (==) instead of an assignment (=).
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
This revomes the code under #if 0 in the s3c24x0_i2c driver.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>
Spi driver for bf60x is different from old one, so implement a new
driver for it.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Add rsi/sdh support for bf60x.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Implements the tstc() interface for the serial driver. Multiplexing
the console between the serial port and a keyboard uses a polling
method of checking if characters are available; this means that the
serial console must be non-blocking when attempting to read
characters.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
If the NAND is locked tight, commands such as lock and unlock will not
work, but the NAND chip may not report an error. Check the lock tight
status before attempting such operations so that an error status can be
reported if we know the operation will not succeed.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The differences include the number of GPIOs and that one is
not required to set the pinmux on request.
Signed-off-by: Holger Hans Peter Freyther <holger@freyther.de>
If CONFIG_NAND_ECC_BCH is set we use 4-bit error corretion code
instead of the 1-bit error correction code on the NAND device
within this driver.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Add driver for tegra SPI "SLINK" style driver. This controller is
similar to the tegra20 SPI "SFLASH" controller. The difference is
that the SLINK controller is a genernal purpose SPI controller and the
SFLASH controller is special purpose and can only talk to FLASH
devices. In addition there are potentially many instances of an SLINK
controller on tegra and only a single instance of SFLASH. Tegra20 is
currently ths only version of tegra that instantiates an SFLASH
controller.
This driver supports basic PIO mode of operation and is configurable
(CONFIG_OF_CONTROL) to be driven off devicetree bindings. Up to 4
devices per controller may be attached, although typically only a
single chip select line is exposed from tegra per controller so in
reality this is usually limited to 1.
To enable this driver, use CONFIG_TEGRA_SLINK
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for configuring tegra SPI driver from devicetree.
Support is keyed off CONFIG_OF_CONTROL. Add entry in seaboard dts
file for spi controller to describe seaboard spi.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for Numonyx N25Q256A SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Numonyx N25Q32A SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Numonyx N25Q32 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Numonyx N25Q64A SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Winbond's W25Q64W SPI flash.
This device is used on xilinx zynq emulation platform.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrected the first byte of idcode1 for S25FL256S SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_ARM_DCC_MULTI should be also removed in the patch
"serial: Remove CONFIG_SERIAL_MULTI from serial drivers"
(sha1: a382725060)
Because the driver defines serial_* functions
which cause conflict with serial.c (multiple definition of serial_*)
Removing CONFIG_SERIAL_MULTI function also require to define
default_serial_console for cases where another serial driver
is not available in the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
Currently we have "unsigned long blkcnt" which is fine with
CONFIG_SYS_64BIT_LBA undefined because "lbaint_t" is basically the same
"unsigned long".
If CONFIG_SYS_64BIT_LBA gets defined "lbaint_t" is defined as "unsigned
long long".
Even though not many embedded systems have CONFIG_SYS_64BIT_LBA defined
it's good to have types in function implementation that match exactly
with prototypes.
Signed-off-by: Alexey Brodkin <alexey.brodkin@gmail.com>
Move these fields into arch_global_data and tidy up. This is needed for
both ppc and m68k since they share the i2c driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
System ACE compact flash controller supports either 8-bit (default) or
16-bit data transfers. And in corresponding driver we need to implement
read/write of 16-bit data words properly for both modes of operation.
In existing code if width==8 both branches get executed which may cause
unexpected behavior of SystemAce controller.
Addition of "else" fixes described issue and execution is done as
expected for both (8-bit and 16-bit) data bus widths.
Signed-off-by: Alexey Brodkin <alexey.brodkin@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The local functions in the mxs i2c driver are not marked static, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
The MX23 has different layout of DMA channels. Fix the MMC
driver to support MX23.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
