This option provides better performance and should really always be
enabled. Make this be default y.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Currently the chipselect used to identify the corresponding NAND chip
is stored at the controller and only set during fsl_ifc_chip_init().
This way, only the last NAND chip is working, as the previous value
of cs_nand gets overwritten.
In order to solve this issue the chipselect is computed on demand by
evaluating the bank variable. Thus, the correct chipselect for each
NAND chip operation is used.
Tested on hardware with two NAND chips connected to the IFC
controller.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Scott Wood <oss@buserror.net>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
In old days, the MTD subsystem in Linux had debug facility like
DEBUG(MTD_DEBUG_LEVEL1, ...).
They were all replaced with pr_debug() until Linux 3.2. See Linux
commit 289c05222172 ("mtd: replace DEBUG() with pr_debug()").
U-Boot still uses similar macros. Covert all of them for easier sync.
Done with the help of Coccinelle.
The semantic patch I used is as follows:
// <smpl>
@@
expression e1, e2;
@@
-MTDDEBUG(e1, e2)
+pr_debug(e2)
@@
expression e1, e2;
@@
-MTDDEBUG(e1, e2,
+pr_debug(e2,
...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable clock in the probe hook. The clock rate will be necessary
when setup_data_interface hook is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Set Features (0xEF) command toggles the R/B# pin after 4 sub feature
parameters are written.
Currently, nand_command(_lp) calls chip->dev_ready immediately after
the address cycle because NAND_CMD_SET_FEATURES falls into default:
label. No wait is needed at this point.
If you see nand_onfi_set_features(), R/B# is already cared by the
chip->waitfunc call.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[ Linux commit: c5d664aa5a4c4b257a54eb35045031630d105f49 ]
Read ID (0x90) command does not toggle the R/B# pin. Without this
patch, NAND_CMD_READID falls into the default: label, then R/B# is
checked by chip->dev_ready().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[ Linux commit: 3158fa0e739615769cc047d2428f30f4c3b6640e ]
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Denali IP does not update the revision register properly.
Allow to override it with SoC data associated with compatible.
Linux had already finished big surgery of this driver, but I need
to prepare the NAND core before the full sync of the driver.
For now, I am fixing the most fatal problem on UniPhier platform.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
A patch for NAND uclass support was proposed about half a year ago:
https://patchwork.ozlabs.org/patch/722282/
It was not merged and I do not see on-going work for this.
Without DM-based probing, we need to set up pinctrl etc. in an ad-hoc
way and give lots of crappy CONFIG options for base addresses and
properties, which are supposed to be specified by DT. This is painful.
This commit just provides a probe hook to retrieve "reg" from DT and
allocate private data in a DM manner. This DT driver is not essentially
a NAND driver, in fact it is (ab)using UCLASS_MISC. Once UCLASS_NAND is
supported, it would be possible to migrate to it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_NAND
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Sync up a few more, add imply's]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Currently the following build error is seen when a board using MMC SPL
is built and the MXS nand driver is also selected:
arch/arm/cpu/armv7/built-in.o: In function `arch_cpu_init':
arch/arm/cpu/armv7/mx6/soc.c:432: undefined reference to 'mxs_dma_init'
On mx6 the only user of mxs_dma_init() is the mxs nand driver, so
move it there.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Make make nand_info array static, since all direct users of nand_info array
have been converted to use get_nand_dev_by_index() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
nand_info is used all over the file so abstract it with
get_nand_dev_by_index() which will help for DM conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
Obtain NAND controller setup parameters from the device
tree instead of using hardcoded values.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Scott Wood <oss@buserror.net>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
nand_spl_load_image implementation was copied over into three
different drivers and now with nand_spl_read_block used for
ubispl situation gets even worse. For now use least intrusive
solution and #include the same implementation to nand drivers.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Because there isn't the implementation of gpio_set/get_value()
and gpio_set/get_value() after the at91 gpio driver is converted
to support the driver model, use at91_set_gpio_value() and
at91_get_gpio_value()
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Various commands to NAND flash results in the NAND flash becoming busy.
For those commands the SoC should wait until the NAND indicates it is
no longer busy before sending further commands. However, there is a delay
between the time the SoC sends its last command and when the NAND flash
sets its Ready/Busy Pin. This delay (tWB) must be respected or the SoC may
falsely assume the flash is ready when in reality it just hasn't had enough
time to indicate that it is busy.
Properly delaying by tWB is already done for nand_command/nand_command_lp
in nand_base.c including the version of it in the Linux kernel. Therefore,
this patch brings the handling of tWB delay inline to nand_base.c
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[trini: Reformat comments slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
The SPL image needs to be built with a different ECC configuration than the
U-Boot binary.
Add Kconfig options with defaults to provide a value that should work for
anyone, but is still configurable if needs be.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The default U-Boot offset for the Allwinner SoCs was set to 32kB.
This was probably to try to maintain some compatibility with the current
image that we build for the MMC where the U-Boot binary is also located at
a 32kB offset.
However, this causes a number of issues. The first one is that it prevents
us from using a backup SPL entirely, which is troublesome in case where the
first would be corrupt (especially on MLC which have a higher number of
bitflips).
We also cannot use the original MMC image on the NAND, because we need to
prepare the SPL image to include the ECCs and randomizer settings, which
reduces the interest of setting it at that particular offset.
It also prevents us from upgrading and flashing the U-Boot and SPLs
independantly, since it's very likely that it will fall in the same erase
block.
Since that default wasn't used by any board, change it for 8MB, which will
be in an erase block of its own, all the erase blocks being multiple of
two. The highest erase block size we encountered is 4MB, which means that
in this particular setup, the first and second erase blocks will be for the
SPL and its backup, and the third for U-Boot.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
We'll need that symbol so that the default offset are defined
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When trying to autodetect the ECC and randomization configurations, the
driver starts with a randomization disabled and no seeds.
In this case, the number of seeds is obviously 0, and the randomize boolean
is set to false.
However, the logic that retrieves the seed for a given page offset will
blindly use the number of seeds, without testing if the randomization is
enabled, basically doing a modulo by 0.
As it turns out, the libgcc in the common toolchain returns 0 here, which
was our expected value in such a case, and why we would not detect it.
However, U-Boot's libgcc will for some reason return from the function
instead, resulting in an error to load the U-Boot binary in the SPL.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add initialization flag to avoid initializing NAND Flash multiple
times, otherwise it will calculate a wrong total size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).
Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Replace hardcoded value with defined constant SECTOR_BYTES.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
SPL from nand will print 'NAND' in boot_from_devices based on
the image_loader name, remove the extra 'NAND ' in mxs_nand_spl driver.
Original behaviour:
-------------------
U-Boot SPL 2017.01-rc2-gf84dd8b (Jan 02 2017 - 22:24:19)
Trying to boot from NANDNAND : 512 MiB
After the fix:
-------------
U-Boot SPL 2017.01-rc2-gf84dd8b-dirty (Jan 02 2017 - 23:17:00)
Trying to boot from NAND: 512 MiB
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
The OMAPL138-LCD board uses a NAND chip with a 16 bits bus. Add
support into the davinci driver for 16 bit bus NAND chips.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the description of the Toshiba TC58NVG2S0H SLC nand to the nand_ids
table so we can use the NAND ECC infos and the ONFI timings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Clear ecc ON bit while sending read command as all types
of read command(like reading spare) doesnt need ECC to be
enabled. It has been anyway taken care in other places
whereever required using arasan_nand_enable_ecc().
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the command buffer gets allocated with a size of 32 bytes.
This causes warning messages on systems with cache lines bigger than
32 bytes:
CACHE: Misaligned operation at range [9df17a00, 9df17a20]
Define command buffer to be at least 32 bytes, but more if cache
line is bigger.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Now that nand_info[] is an array of pointers we need to test the
pointer itself rather than using name as a proxy for NULLness.
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
In commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data") the assignment of mtd->priv was removed
but was not replaced. This adds the required nand_set_controller_data()
call.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write, although
it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating until the watchdog timeout triggers.
To reproduce the issue on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Add a full-id entry for the H27QCG8T2E5R‐BCF NAND.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.
The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
The original commit has been slightly reworked to use the fdtdec_xxx()
helpers (instead of the of_xxxx() ones).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
