Commit Graph

10 Commits

Author SHA1 Message Date
Ye Li
7c4f9b3755 imx: ddr: imx8m: Move selfref_en after DDR scrub
When doing DDR scrub, the DDR may enter into self refresh if the
selfref_en is enabled before DDR scrub. This will cause scrub
can't complete that SBRSTAT.scrub_done won't be set.

Since the selfref_en can be programmed during the course of
normal operation, move it after DDR scrub

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 11:30:30 +01:00
Oliver Chen
b335966958 drivers: ddr: imx Workaround for i.MX8M DDRPHY rank to rank issue
Add logic to automatically update umctl2's setting based
on phy training CDD value for rank to rank space issue

Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Oliver Chen <Oliver.Chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Sherry Sun
f3acb02386 drivers: ddr: imx8mp: Add inline ECC feature support
the DRAM Controller in i.MX8MP will support a feature called "Inline ECC".
This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and
DDR3L). When this feature is enabled by software, the DRAM Controller
reserves 12.5% of DRAM capacity for ECC information, and presents only
the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to
the rest of the SoC.
The DRAM memory can be divided into 8 regions so that if a use case only
requires ECC protection on a subset of memory, then only that subset of
memory need support inline ECC. If this occurs, then there is no
performance penalty accessing the non-ECC-protected memory (no need to
access ECC for this portion of the memory map). This is all configured
with the DRAM Controller.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Jacky Bai
1eb325af16 driver: ddr: imx: correct the pwrctl setting of selfref_en on imx8m
The 'selfref_en' should be bit'0', so correct the setting to
enable the auto self-refresh.

Reviewed-by: Jian Li <jian.li@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Jacky Bai
355c620666 driver: ddr: imx: skip ddr_ss_gpr config on imx8mn
There is no DDR_SS_GPR0 exits on i.MX8MN, so skip setting
this register on i.MX8MN.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Simon Glass
f7ae49fc4f common: Drop log.h from common header
Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:18 -04:00
Frieder Schrempf
83083febf5 ddr: imx8m: Return error values from LPDDR4 training
In cases when the same SPL should run on boards with i.MX8MM, that
differ in DDR configuration, it is necessary to try different
parameters and check if the training done by the firmware suceeds or
not.

Therefore we return the DDR training/initialization success to the
upper layer in order to be able to retry with different settings if
necessary.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2020-01-07 10:26:57 +01:00
Fabio Estevam
0d3bc81391 imx8m: ddr_init: Move ddr_init() messages to debug level
Currently inside ddr_init() there is a mix of printf() and debug()
level messages.

Since this type of information is useful for debug purposes,
convert all of them to debug level for consistency.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-12-27 12:14:25 +01:00
Jacky Bai
69b8e50975 ddr: imx8m: Fix the ddr init hang on imx8mq
On, i.MX8MQ, the PLL config must be done when ddrmix
isolation is released. So move the dram pll init after
iso config done. For other i.MX8M SOC, either init pll
before or after isolation is ok.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:37 +02:00
Jacky Bai
825ab6b406 driver: ddr: Refine the ddr init driver on imx8m
Refine the ddr init driver to make it more reusable for different
DDR type(LPDDR4, DDR4 & DDR3L). So we can reduce some redundant
code.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:37 +02:00