At present sorting and expanding entries are side-effects of the
CheckEntries() function. This is a bit confusing, as 'checking' would
not normally involve making changes.
Move these steps into the Pack() function instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function just calls CheckEntries() in the only non-trivial
implementation. Drop it and use CheckEntries() directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a section is compressed, all entries within it are grouped together
into a compressed block of data. This obscures the start of each
individual child entry.
Avoid reporting bogus 'image-pos' properties in this case, since it is
not possible to access the entry at the location provided. The entire
section must be decompressed first.
CBFS does not support compressing whole sections, only individual files,
so needs no special handling here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Section contents is not set up when ObtainContents() is called, since
packing often changes the layout of the contents. Ensure that the contents
are correctly recorded by making this function regenerate the section. It
is normally only called by the parent section (when packing) or by the
top-level image code, when writing out the image. So the performance
impact is fairly small.
Now that sections have their contents in their 'data' property, update
testSkipAtStartSectionPad() to check it.
Signed-off-by: Simon Glass <sjg@chromium.org>
When compressing an entry, the original uncompressed data is overwritten.
Store it so it is available if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present padding of sections is inconsistent with other entry types, in
that different pad bytes are used.
When a normal entry is padded by its parent, the parent's pad byte is
used. But for sections, the section's pad byte is used.
Adjust logic to always do this the same way.
Note there is still a special case in entry_Section.GetPaddedData() where
an image is padded with the pad byte of the top-level section. This is
necessary since otherwise there would be no way to set the pad byte of
the image, without adding a top-level section to every image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Each section is padded up to its size, if the contents are not large
enough. Move this logic from _BuildSectionData() to
GetPaddedDataForEntry() so that all the padding is in one place.
With this, the testDual test is working again, so enable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function does the padding needed around an entry. It is
easier to understand what is going on if we have a function that returns
the contents of an entry, with padding included.
Refactor the code accordingly, adding a new GetPaddedData() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a new _BuildSectionData() to hold the code that is now in
GetData(), so that it is clearly separated from entry.GetData() base
function.
Separate out the 'pad-before' processing to make this easier to
understand.
Unfortunately this breaks the testDual test. Rather than squash several
patches into an un-reviewable glob, disable the test for now.
This also affects testSkipAtStartSectionPad(), although it still not
quite what it should be. Update that temporarily for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Alignment does form part of the entry once the image is written out, but
within binman the entry contents does not include the padding. Add
documentation to make this clear, as well as a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Padding becomes part of the entry once the image is written out, but
within binman the entry contents does not include the padding. Add
documentation to make this clear, as well as a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check the contents of each section to make sure it is actually in the
right place.
Also fix a whitespace error in the .dts file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use 'compress' as the property to set the compression of
a 'files' entry. But this conflicts with the same property for entries,
of which Entry_section is a subclass.
Strictly speaking, since Entry_files is in fact a subclass of
Entry_section, the files can be compressed individually but also the
section (that contains all the files) can itself be compressed. With this
change, it is possible to express that.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this is only used by blobs. To allow it to be used by other
entry types (such as sections), move it into the base class.
Also read the compression type in the base class.
Signed-off-by: Simon Glass <sjg@chromium.org>
While a section is the base class of Image, it is more correct to refer
to sections in most places in this file. Fix these comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if 'binman' is typed on the command line, a strange error about
a missing argument is displayed. Fix this.
These does not seem to be standard way to add the 'required' argument in
all recent Python versions, so set it manually.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this feature is tested view the end-at-4gb feature. Add some
tests of its own, including the operation of padding.
The third test here shows binman's current, inconsistent approach to
padding in the top-level section. Future patches in this series will
address this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With of-platdata, the devicetree is supposed to specify all the devices
in the system. So far this hasn't really mattered since of-platdata still
works correctly.
However, new of-platdata features rely on numbering the devices in a
particular order so that they can be referenced by a single integer. It is
tricky to implement this efficiently when other devices are present in the
build.
To address this, disable use of U_BOOT_DEVICE() when of-platdata is
enabled. This seems acceptable as it is not supposed to be used at all,
except in SPL/TPL, where of-platdata is the recommended approach.
This breaks one non-compliant boards at present: mx6cuboxi
Signed-off-by: Simon Glass <sjg@chromium.org>
(disable CONFIG_IMX_THERMAL for mx6cuboxi to avoid a build error)
This feature is incompatble with of-platdata since it uses the
U_BOOT_DEVICE() macro. With of-platdata the only devices permitted are
those created by dtoc.
The driver is not used in SPL anyway, so exclude it from that build.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
At present we use a 'node' pointer in the of-platadata phandle_n_arg
structs. This is a pointer to the struct driver_info for a particular
device, and we can use it to obtain the struct udevice pointer itself.
Since we don't know the struct udevice pointer until it is allocated in
memory, we have to fix up the phandle_n_arg.node at runtime. This is
annoying since it requires that SPL's data is writable and adds a small
amount of extra (generated) code in the dm_populate_phandle_data()
function.
Now that we can find a driver_info by its index, it is easier to put the
index in the phandle_n_arg structures.
Update dtoc to do this, add a new device_get_by_driver_info_idx() to look
up a device by drive_info index and update the tests to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that parent devices are supported with of-platadata, we don't need the
messy code to fix up the parent pointers and allocations on Apollo Lake.
Put the code behind a condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, enabling CONFIG_APL_SPI_FLASH_BOOT does not build since SPI
and SPI flash are not enabled for TPL. Add a condition to fix this and
tidy up a build warning in the SPI-flash driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple test that we can obtain the correct parent for an I2C
device. This requires updating the driver names to match the compatible
strings, adding them to the devicetree and enabling a few options.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present of-platdata does not provide parent information. But this is
useful for I2C devices, for example, since it allows them to determine
which bus they are on.
Add support for setting the parent correctly, by storing the parent
driver_info index in dtoc and reading this in lists_bind_drivers(). This
needs multiple passes since we must process children after their parents
already have been bound.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no devicetree with of-platdata. Update a few uclasses to allow
them to be built for sandbox_spl. Also drop the i2c-gpio from SPL to avoid
build errors, since it does not support of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we update the driver_info struct with a pointer to the device
that it created (i.e. caused to be bound). This works fine when U-Boot SPL
is stored in read-write memory. But on some platforms, such as Intel
Apollo Lake, it is not possible to update the data memory.
In any case, it is bad form to put this information in a structure that is
in the data region, since it expands the size of the binary.
Create a new driver_rt structure which holds runtime information about
drivers. Update the code to store the device pointer in this instead.
Also update the test check that this works.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a test in dtoc for this feature, but not one in U-Boot itself.
Add a simple test that checks that the information comes through
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
With of-platdata, the driver_info struct is updated with the device
pointer when it is bound. This makes it easy for a device to be found by
its driver info with the device_get_by_driver_info() function.
Add a test that all devices (except the root device) have such an entry.
Fix a bug that the function does not set *devp to NULL on failure, which
the documentation asserts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present properties are tested in a roundabout way. The driver's probe()
method writes out the values of the properties and the Python test checks
the output from U-Boot SPL.
Add a C test which checks these values more directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have a pytest that covers of-platadata. Add a very simple
unit test that just checks that a device can be found. This shows the
ability to write these tests in C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a -u flag for U-Boot SPL which requests that unit tests be run. To
make this work, export dm_test_main() and update it to skip test features
that are not used with of-platdata.
To run the tests:
$ spl/u-boot-spl -u
U-Boot SPL 2020.10-rc5 (Oct 01 2020 - 07:35:39 -0600)
Running 0 driver model tests
Failures: 0
At present there are no SPL unit tests.
Note that there is one wrinkle with these tests. SPL has limited memory
available for allocation. Also malloc_simple does not free memory
(free() is a nop) and running tests repeatedly causes driver-model to
reinit multiple times and allocate memory. Therefore it is not possible
to run more than a few tests at a time. One solution is to increase the
amount of malloc space in sandbox_spl. This is not a problem for pytest,
since it runs each test individually, so for now this is left as is.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present DM tests assume that a devicetree is available. This is not the
case with of-platadata.
Update the code to add this condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
Without resizing the SDL window showed by
./u-boot -D -l
is not legible on a high resolution screen.
Allow resizing the window
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present an integer is converted to bytes incorrectly. The whole 32-bit
integer is inserted as the first element of the byte array, and the other
three bytes are skipped. This was not noticed because the unit test did
not check it, and the functional test was checking for wrong values.
Update the code to handle this as a special case. Add one more test to
cover all code paths.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this option is disabled in SPL, meaning that warnings are not
displayed. It is sometimes useful to see warnings in SPL for debugging
purposes.
Add a new Kconfig option to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
