Add first support for STM32MP157C-ED1 board with "Basic" boot chain
1/ Boot Rom: load SPL with STM32 image header in SYSRAM
2/ SPL: power up and initialize the DDR and load U-Boot image
from SDCARD in DDR
3/ U-Boot: search and load extlinux.conf in SDCARD
(DISTRO activated)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Support several pixel format (8bits, 16bits, 24bits & 32bits).
Add new file st_logo_data.h which contains logo
stmicroelectronics_uboot_logo_8bit_rle.bmp.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is safe to always setup the pinmux for UART1 and UART3 to be used in
early_padconf and then if these pins are needed later on, they will be
re-muxed. This allows us to drop the usage of CONFIG_CONS_INDEX here.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
serial# variable is needed to show the device correctly in "fastboot
devices" output. It's useful when we have several devices (in fastboot
mode) connected to single host and want to choose which one to flash.
We can't use omap_die_id_serial() for this, because AM335x lacks
DIE_ID, as can be seen from AM335x TRM. Let's do next:
- reuse board_serial variable (obtained from EEPROM in
set_board_info_env() function) to set serial#
- if board_serial is "unknown", reuse ethaddr variable to set serial#
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard 'xM' does not really have NAND. CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT can/should be empty for 'xM'. This commit sets
the defined values if they exist.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Remove arch/arm/include/asm/arch-stm32fx/stm32_periph.h
as all defines or enums are no more used.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
RK3288 Vyasa has eMMC boot support, with JP4 open.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync rk3288-vyasa board dts from Linux for proper updates and maintenance
- rk3288-vyasa.dts: Similar to Linux dts
- rk3288-vyasa-u-boot.dtsi: u-boot dts changes
Also updated MAINTAINERS for these dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired
to MMC2 slot.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel, except some nodes are removed to make file
compatible with existing dtsi file.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In README.sunxi64 we tell the user how to optionally create
u-boot-sunxi-with-spl.bin by manually running cat. Instead, have the
build system create the file automatically just like it does for 32-bit
sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.
Also, Dirk's address was wrong in one place; fix that as well.
Signed-off-by: Mario Six <six@gdsys.cc>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.
Signed-off-by: Marek Vasut <marex@denx.de>
This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.
Fixes: bfebc8c965 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently SPL_LOAD_FIT is unable to boot from nand on
i.MX6QDL platform, so enable only for MMC boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit edf0093732 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.
These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
These ARM boards are in nice shape and still being used a lot
with e.g. QEMU, so I can maintain them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
To debug device tree issues involving 32- and 64-bit platforms, it is useful to
have a generic 64-bit platform available.
Add a version of the sandbox that uses 64-bit integers for its physical
addresses as well as a modified device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Added CONFIG_SYS_TEXT_BASE to configs/sandbox64_defconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
late in the cycle, so this is something to be done in 2018.05.
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Commit 958d55f26c ("MAINTAINERS: Take over BCM2835 maintainership") put
me in as maintainer for the RPi soc, but forgot to update the board
MAINTAINERS file.
Add me there too.
Signed-off-by: Alexander Graf <agraf@suse.de>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is no EMMC symbol in the "enable different boot versions for the
shc board" choice. SHC_EMMC was probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection EMMC (undefined) of <choice> (defined at board/bosch/shc/Kconfig:15) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Move dram_init(), dram_init_banksize() and get_effective_memsize() to
arch/arm/mach-imx/mx5/mx53_dram.c, where it can be reused by m53evk and
mx53loco.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
