Jz4740 NAND flash controller can support:
* MLC NAND as well as SLC NAND
* all 8-bit/16-bit NAND flash devices
* HAMMING and RS hardware ECC
* automatic boot up from NAND flash devices
nand_ecclayout is set up for 2GiB NAND chip mounted in Qi LB60.
We'll bring up boot-from-NAND support in nand_spl/ in the future.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
This fixes that u-boot gets stuck when a bitflip was detected
during "ubi part <ubi_device>". If a bitflip was detected UBI tries
to copy the PEB to a different place. This needs that the eba table
are initialized, but this was done after the wear levelling worker
detects the bitflip. So changes the initialisation of these two
tasks in u-boot.
This is a u-boot specific patch and not needed in the linux layer,
because due to commit 1b1f9a9d00
UBI: Ensure that "background thread" operations are really executed
we schedule these tasks in place and not as in linux after the inital
task which schedule this new task is finished.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In nand_davinci_readecc(), select the correct NANDF<n>ECC register based
on CONFIG_SYS_NAND_CS rather than hardcoding the choice of NANDF1ECC.
This allows 1-bit hardware ECC to work with chip select other than CS2.
Note this now matches the usage in nand_davinci_enable_hwecc(), which
already had the correct handling, and allows refactoring to a single
function encapsulating the register read.
Without this fix, writing NAND pages to a chip not wired to CS2 would
result in in the ECC calculation always returning FFFFFF for each
512-byte segment, and reading back a correctly written page (one with
ECC intact) would always fail. With this fix, the ECC is written and
verified correctly.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix:
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:225:6: warning: unused variable 'devices_found'
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
[-Wunused-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
* 'master' of git://git.denx.de/u-boot-nand-flash:
PPC: Fix socrates NAND problem
PPC: Fix fsl_upm.c by renaming nand handling functions
NAND: Make page, erase, oob size available via cmd_nand
mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
NAND: Add -y option to nand scrub command
NAND: Add nand read.raw and write.raw commands
NAND: Really ignore bad blocks when scrubbing
spl, nand: add 4bit HW ecc oob first nand_read_page function
mxc_nand: fix a problem writing more than 32MB
mxc_nand: fixed some typos (cosmetic)
nand: increase chip_delay in mv kirkwood nand driver
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
This avoids colision with nand subsystem's functions.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
v2: fix broken mailer
Signed-off-by: mhench <mhench@elutions.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: use chip instead of redundant priv_nand]
Signed-off-by: Scott Wood <scottwood@freescale.com>
When writing 0x4000 to the unlockend_blkaddr register, large writes to
a 2k page NAND sometimes fail. The current kernel driver writes 0xFFFF
to this register for V2 of the nand controller.
However on an i.MX31 this also fixes writes larger than 32MB.
The datasheet is very unspecific, but (0x4000=16384)*2000
roughly fits the limits we're encountering with NAND writes.
This problem might be NAND chip specific.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The new SAMSUNG NAND Flash K9F1G08U0D require a bigger chip_delay.
The Data Transfer from Cell to Register is >= 35us. Other Vendors
and older chips normally use >= 25us. To have enough margin 40us
is selected.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
vmt.c: In function ‘ubi_free_volume’:
vmt.c:681:6: warning: variable ‘err’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
nand_bbt.c: In function ‘search_bbt’:
nand_bbt.c:465:6: warning: variable ‘bits’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Add NAND support (including spl) on IFC, such as is found on the p1010.
Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC. UBI should
work, as it does not use OOB for anything but ECC.
When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
On some systems, we get a warning when %lu is used with size_t's, so
use the correct format string.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add support of MX25L4005 and MX25L8005 according to the datasheet
http://www.mct.net/download/macronix/mx25l8005.pdf
This patch has been tested with MX25L4005 and MX25L8005
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Newer SST flashes have dropped the Auto Address Increment (AAI) word
programming (WP) modes in favor of the standard page programming mode
that most flashes now support. So add a flags field to the different
flashes to support both modes with new and old styles.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Every spi flash uses the same write disable command, so unify this in
the common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fixed commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Now that the common spi_flash structure tracks all the info that these
drivers need, kill off their local state indirection and use just what
the common code provides.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Once we add a new page_size field for write lengths, we can unify the
write methods for most of the spi flash drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for 16 bit NAND devices attached to the
NDFC on ppc4xx processors. Two config entries were added:
CONFIG_SYS_NDFC_16 - Setting this tells the NDFC that a
16 bit device is attached.
CONFIG_SYS_NDFC_EBC0_CFG - This is for the External Bus
Controller configuration register.
Also, a new ndfc_read_byte() function was added which does not
first convert the data to little endian.
The NAND SPL was also modified to do 16bit bad block testing
when a 16 bit chip is being used.
Signed-off-by: Alex Waterman <awaterman@dawning.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add a flag to nand_read_skip_bad() such that if true, any trailing
pages in an eraseblock whose contents are entirely 0xff will be
dropped.
The implementation is via a new drop_ffs() function which is
based on the function of the same name from the ubiformat
utility by Artem Bityutskiy.
This is as-per the reccomendations of the UBI FAQ [1]
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When specified in the flags argument of nand_write, WITH_YAFFS_OOB causes an
operation which is mutually exclusive with the 'usual' way of writing.
Add a check that client code does not specify WITH_YAFFS_OOB along with any
other flags and add a comment indicating that the WITH_YAFFS_OOB flag should
not be mixed with other flags.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In a future commit the behaviour of nand_write_skip_bad()
will be further extended.
Convert the only flag currently passed to the nand_write_
skip_bad() function to a bitfield of only one allocated
member. This should avoid an explosion of int's at the
end of the parameter list or the ambiguous calls like
nand_write_skip_bad(info, offset, len, buf, 0, 1, 1);
nand_write_skip_bad(info, offset, len, buf, 0, 1, 0);
Instead there will be:
nand_write_skip_bad(info, offset, len, buf, WITH_YAFFS_OOB |
WITH_OTHER);
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Replace an incorrect 'read' with 'write' in a comment.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For newer STM parts where CFI >= 1.1, there is a byte in the extended
structure that declares the flash layout type (just like the AMD parts),
so key off of that to find out when we need to reverse the geometry.
This can be seen with M29W640 parts where U-Boot does:
Bank # 1: CFI conformant FLASH (16 x 16) Size: 8 MB in 135 Sectors
AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22ED
Erase timeout: 8192 ms, write timeout: 1 ms
Buffer write timeout: 1 ms, buffer size: 16 bytes
Sector Start Addresses:
20000000 RO 20002000 RO 20004000 RO 20006000 RO 20008000 RO
2000A000 RO 2000C000 RO 2000E000 RO 20010000 RO 20020000 RO
...
But Linux does:
physmap platform flash device: 00800000 at 20000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank.
Manufacturer ID 0x000020 Chip ID 0x0022ed
physmap-flash.0: Swapping erase regions for top-boot CFI table.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The status polling can take a while, so make sure we kick the
watchdog after each successful poll.
Signed-off-by: Patrick Sestier <psestier@mircom.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Move the header file and definitions of ftsmc020
static memory control unit from a320 SoC folder to
"drivers/mtd" folder.
This change will let other SoC which also use ftsmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
I ran into a problem where the reset was failing except when I enabled
debugging support. After talking with Garret Swalling at Spansion I
was told that the GL-N series of devices require a 500ns wait for the
reset to complete. The below patch adds a 1us delay after all reset
commands.
-Aaron Williams
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The M29W800DT parts also report their geometry with the sector layout
reversed. So add that ID to the flash_fixup_stm function.
Otherwise, we get:
bfin> flinfo
Bank # 1: CFI conformant FLASH (16 x 16) Size: 1 MB in 19 Sectors
AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22D7
Erase timeout: 8192 ms, write timeout: 1 ms
Sector Start Addresses:
20000000 20004000 20006000 20008000 20010000
20020000 20030000 20040000 20050000 20060000
20070000 20080000 20090000 200A0000 200B0000
200C0000 200D0000 200E0000 200F0000
Reported-by: Jianxi Fu <fujianxi@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch sync with Brian's patch on Linux in nand_flash_detect_onfi()
commit b7b1a29d94c17e4341856381bccb4d17495bea60
Author: Brian Norris <computersforpeace@gmail.com>
Date: Sun Dec 12 00:23:33 2010 -0800
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
In checking for the ONFI revision, the first conditional (for checking
"unsupported" ONFI) seems unnecessary. All ONFI revisions should be
backwards-compatible; even if this is not the case on some newer ONFI
revision, it should simply fail the second version-checking if-else block
(i.e., the bit-fields for 1.0, 2.0, etc. would not be set to 1). Thus, we
move our "unsupported" condition after having checked each bit field.
Also, it's simple enough to add a condition for ONFI revision 2.3. Note
that this does *NOT* mean we handle all new features of ONFI versions
above 1.0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
This patch sync with David's patch on Linux in nand_flash_detect_onfi()
commit 4ccb3b4497ce01fab4933704fe21581e30fda1a5
Author: David Woodhouse <David.Woodhouse@intel.com>
Date: Fri Dec 3 16:36:34 2010 +0000
mtd: nand: Fix integer overflow in ONFI detection of chips >= 4GiB
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Commit 6ee1416e81 (mtd, cfi: introduce
void flash_protect_default(void)) introduced a bug which resulted in
boards that define CONFIG_SYS_FLASH_AUTOPROTECT_LIST not compiling with
the the following errors and warning:
ptyser@petert u-boot $ make -s xpedite520x
Configuring for xpedite520x board...
cfi_flash.c: In function 'flash_protect_default':
cfi_flash.c:2118: error: 'i' undeclared (first use in this function)
cfi_flash.c:2118: error: (Each undeclared identifier is reported only once
cfi_flash.c:2118: error: for each function it appears in.)
cfi_flash.c:2118: error: 'apl' undeclared (first use in this function)
cfi_flash.c:2118: error: invalid application of 'sizeof' to incomplete type 'struct apl_s'
cfi_flash.c: In function 'flash_init':
cfi_flash.c:2137: warning: unused variable 'apl'
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Heiko Schocher <hs@denx.de>
