Fix:
db64360.c: In function 'debug_led':
db64360.c:413:6: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_real_open':
mv_eth.c:424:6: warning: variable 'port_status' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_stop':
mv_eth.c:642:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_xmit':
mv_eth.c:718:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_receive':
mv_eth.c:803:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_get_stats':
mv_eth.c:902:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_update_stat':
mv_eth.c:930:24: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c:929:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_print_stat':
mv_eth.c:1011:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'eth_clear_mib_counters':
mv_eth.c:2068:15: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'check_dimm':
sdram_init.c:289:50: warning: variable 'trrd_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:37: warning: variable 'tras_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:24: warning: variable 'trcd_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:8: warning: variable 'trp_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:279:34: warning: variable 'devicesForErrCheck' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'setup_sdram':
sdram_init.c:1256:13: warning: variable 'check' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'initdram':
sdram_init.c:1735:25: warning: variable 'check' set but not used [-Wunused-but-set-variable]
sdram_init.c:1733:14: warning: variable 's1' set but not used [-Wunused-but-set-variable]
sdram_init.c:1733:6: warning: variable 's0' set but not used [-Wunused-but-set-variable]
Note: no attempt was make to clean up the mess coding style and
other issues in sdram_init.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
