In the next commit, rtc_mktime(), for compatibility with linux, will be
implemented using rtc_mktime(), which is no longer drivers/rtc specific.
So move this file under lib/.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Extract all sysboot command related code from pxe.c to new sysboot.c
Update Kconfig to insure that DISTRO_DEFAULT select new CMD_SYSBOOT
command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As sysboot and pxe commands are sharing piece of code, migrate this
common code into a new file pxe_utils.c to prepare sysboot command
code extraction from pxe.c
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The command cp fails on sandbox because the address is used
directly. To fix this issue, we call the function map_sysmem
to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The command iminfo fails on sandbox because the address
is used directly. To fix this issue, we call the function
map_sysmem to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Defconfigs have been fixed, now we can add proper dependencies in
Kconfig. SPI FLASH is still not dependent on MTD (deeper rework needed).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A type error in the implementation of the efidebug command is fixed.
-----BEGIN PGP SIGNATURE-----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=spg0
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc5
A type error in the implementation of the efidebug command is fixed.
I detected the following error in sandbox with Clang on Travis CI:
+cmd/efidebug.c:703:15: error: result of comparison of constant
9223372036854775822 with expression of type 'int' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
+ else if (ret == EFI_NOT_FOUND)
+ ~~~ ^ ~~~~~~~~~~~~~
Simply changing a type of 'ret' to efi_status_t will fix this error.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
pxe command parses the init ramfs address(through initrd lable in
pxe config file), but is not passing it to bootm command as argument
as bootm_argc count is not increased.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we do not have CONFIG_BLK (or SPL/TPL) enabled there are very few
cases where we need the blk_legacy code linked in. To catch these, build
when we have CONFIG_HAVE_BLOCK_DEVICE set. In addition, we only need
cmd/blk_common.o to be linked in when we have CONFIG_HAVE_BLOCK_DEVICE
set, so make use of that directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is not defined by any boards so the feature is not used.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't need to be in common.h so move them out into a new header.
Also add some missing comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some of these have a space before the bracket. Drop it to fix the style.
Add some missing function comments while here.
Note that u32 and u8 cannot be used here since crc.h is included on the
host side.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On the sandbox the UEFI binaries must match the host architectures.
Adjust the Makefiles. Provide the PE/COFF header and relocation files.
Allow building helloworld.efi on the sandbox.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Due to the commit 4b0bcfa7c4 ("Kconfig: Migrate CONFIG_BOOTM_* options")
BOOTEFI and BOOTEFI_HELLO_COMPILE (and other BOOTEFI configs) are
displayed in a long distance. This will make it difficult for us to
understand that those configurations are closely related.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
That option is currently not used by any defconfig and could not be set
anymore since it became mandatory to used Kconfig when introducing new
options with U-Boot v2016.11 or commit eed921d923 ("Kconfig: Add a
whitelist of ad-hoc CONFIG options") and commit 371244cb19 ("Makefile:
Give a build error if ad-hoc CONFIG options are added").
It was also not considered when fixing build warnings in
commit 39ac34473f ("cmd_mtdparts: use 64 bits for flash size,
partition size & offset") and could probably not be compiled anyway
after commit dfe64e2c89 ("mtd: resync with Linux-3.7.1"), which
renamed some members of struct mtd_info … so it was probably broken
since then, which was U-Boot v2013.07-rc1.
However it still seems to work, see example output below:
U-Boot 2019.10-00035-g06a9b259ca-dirty (Oct 30 2019 - 14:03:44 +0100)
CPU: SAMA5D27 1G bits DDR2 SDRAM
Crystal frequency: 24 MHz
CPU clock : 492 MHz
Master clock : 164 MHz
Model: ***
DRAM: 128 MiB
NAND: 256 MiB
Loading Environment from NAND... OK
In: serial@f8020000
Out: serial@f8020000
Err: serial@f8020000
Net: eth0: ethernet@f8008000
Hit keys 'tt' to stop autoboot (3 seconds).
U-Boot> mtdparts
device nand0 <atmel_nand>, # parts = 8
#: name size net size offset mask_flags
0: bootstrap 0x00040000 0x00040000 0x00000000 1
1: uboot 0x000c0000 0x000c0000 0x00040000 1
2: env1 0x00040000 0x00040000 0x00100000 0
3: env2 0x00040000 0x00040000 0x00140000 0
4: fpga_led 0x00040000 0x00040000 0x00180000 1
5: reserved 0x00040000 0x00040000 0x001c0000 1
6: rootfs_rec 0x03200000 0x03200000 0x00200000 1
7: filesystem 0x0cc00000 0x0cb80000 (!) 0x03400000 0
active partition: nand0,0 - (bootstrap) 0x00040000 @ 0x00000000
defaults:
mtdids : nand0=atmel_nand
mtdparts: mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env1),256k(env2),256k(fpga_led)ro,256k(reserved)ro,50M(rootfs_rec)ro,-(filesystem)
Signed-off-by: Alexander Dahl <ada@thorsis.com>
This declaration is not used anywhere in the whole tree. There is a
function 'mtd_id_parse()' which was renamed from 'id_parse()' in
commit 68d7d65100 ("Separate mtdparts command from jffs2"), but that
function is not used (anymore?) in cmd nand and build is fine without
that declaration, so it's probably just safe to remove.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
-----BEGIN PGP SIGNATURE-----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=f0m8
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc2
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
Add optional parameter to 'avb verify' sub-command, so that user is able
to specify which slot to use, in case when user's partitions are
slotted. If that parameter is omitted, the behavior of 'avb verify' will
be the same as before, so user API is content.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
'THOR' download command requires DFU infrastructure to properly flash
board images. It can be used without enabling DFU command, so add such
dependency to Kconfig.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
With this patch, when setting UEFI variable with "env set -e" command,
we will be able to
- specify vendor guid with "-guid guid",
- specify variable attributes, BOOTSERVICE_ACCESS, RUNTIME_ACCESS,
respectively with "-bs" and "-rt",
- append a value instead of overwriting with "-a",
- use memory as variable's value instead of explicit values given
at the command line with "-i address,size"
If guid is not explicitly given, default value will be used.
Meanwhile, "env print -e," will be modified so that it will NOT dump
a variable's value if '-n' is specified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If DM_SPI_FLASH enabled that means it is using sf command
for flash interface to access.
SPI_FLASH can be used via sf command and board/driver
functions to call spi flash ops, so mark it default only
for DM_SPI_FLASH.
This would prevent explicit adding of CONFIG_CMD_SF when
DM_SPI_FLASH being enabled.
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Support for commands to initialize and configure UFS devices.
TODO: Add Support for commands to resize and reconfigure LUNs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
U-Boot now supports the "skip_check" flag to optionally skip the CRC
check at open time. Currently its only possible to set this bit upon
UBI volume creation. But it might be very useful to also set this bit
on already installed systems (e.g. field upgrade) to make also use of
the boot-time decrease on those systems.
This patch now adds a new "ubi" command "ubi skipcheck" to set or clear
this bit in the UBI volume header:
=> ubi skipcheck rootfs0 on
Setting skip_check on volume rootfs0
BTW: This saves approx. 10 seconds Linux bootup time on a MT7688 based
target with 128MiB of SPI NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Some users of static UBI volumes implement their own integrity check,
thus making the volume CRC check done at open time useless. For
instance, this is the case when one use the ubiblock + dm-verity +
squashfs combination, where dm-verity already checks integrity of the
block device but this time at the block granularity instead of verifying
the whole volume.
Skipping this test drastically improves the boot-time.
Adapted to U-Boot by Stefan Roese.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
The aes command used to segfault when accessing memory in sandbox.
The pointer accesses should be mapped.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
