The new boardspecific DDR2 controller configuration is used for the Yucca
board. Now the Yucca board with 440SPe Rev. A chips is also supported.
Signed-off-by: Stefan Roese <sr@denx.de>
- Add optional ECC generation routine to preserve existing
RAM values. This is needed for the Linux log-buffer support
- Add optional DDR2 setup with CL=4
- GPIO50 not used anymore
- Lime register setup added
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
- Show on the Status LEDs, some States of the board.
- Get the MAC addresses from the EEProm
- use PREBOOT
- use the CF on the board.
- check the U-Boot image in the Flash with a SHA1
checksum.
- use dynamic TLB entries generation for the SDRAM
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 533 nor ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand ;to configure the board for 667MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
The latest changes showed a problem with the location of the NAND-SPL
image in the OCM and the init-data area (incl. cache). This patch
fixes this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.
I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variable
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the "normal" Bamboo NOR booting port, so
that it is compatible with the coming soon NAND booting
Bamboo port.
It also enables the 2nd NAND flash on the Bamboo.
Signed-off-by: Stefan Roese <sr@denx.de>
After being reset in mpc5xxx_fec_init_phy(), PHY goes into FX mode, in which
networking does not function. This commit switches PHY to TX mode by clearing
the FX_SEL bit of Mode Control Register. It also reverses commit
008861a2f3, i.e., a temporary workaround.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
This patch updates the Acadia (405EZ) support for the new 1.1 board
revision. It also adds support for NAND FLASH via the 4xx NDFC.
Please note that the jumper J7 must be in position 2-3 for this
NAND support. Position 1-2 is for NAND booting only. NAND booting
support will follow later.
Signed-off-by: Stefan Roese <sr@denx.de>
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.
This allows for maximum clocking speeds to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>