Remove the leading "0x" from rpc node to fix the below dtc warning:
Warning (simple_bus_reg): Node /soc/rpc@0xee200000 simple-bus unit
address format error, expected "ee200000"
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Implement get_pin_muxing() callback so that pinmux status
command can be used on Renesas platforms.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
By default on startup all the pin types are configured to
PINMUX_TYPE_NONE (in sh_pfc_map_pins()), when pin is set as GPIO the
pin type is updated to PINMUX_TYPE_GPIO. But the type is not updated
when the pin is set as a function in sh_pfc_pinctrl_pin_set() or
sh_pfc_pinctrl_group_set() calls (these calls only set the MUX if
the pin type is PINMUX_TYPE_NONE ie unused).
So with the current implementation pin functionality could be overwritten
silently, for example if the same pin is added for SPI and serial.
This patch makes sure of updating pin type after every successful call to
sh_pfc_config_mux() and thus fixing from pin functionality to be
overwritten. Also a warning message is printed if the current pin is being
overwritten before abort.
This also avoids pin re-muxing to same type that is for example from
command line device is asked to re-probe/select (mmc dev x) we return
early with success in this case as the pin is already muxed.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
This doc describes the procedure to build, flash and
boot Linux using U-boot on Microchip MPFS Icicle Kit.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This patch adds Microchip MPFS Icicle Kit support. For now, only
NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are
enabled. The Microchip MPFS Icicle defconfig by default builds
U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run
in S-Mode as payload of HSS + OpenSBI.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Add clock driver code for the Microchip PolarFire SoC. This driver
handles reset and clock control of the Microchip PolarFire SoC device.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Read phy address from device tree and use it to find the phy device
if not found then search in the range of 0 to 31.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Enable 32-bit or 64-bit DMA in the macb driver based on the macb
hardware compatibility and it is configured with structure macb_config
in the driver.
The Microchip PolarFire SoC Memory Protection Unit(MPU) gives the 64-bit
DMA access with the GEM, the MPU transactions on the AXI bus is 64-bit
not 32-bit So 64-bit DMA is enabled for the Microchip PolarFire SoC GEM.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
dma_addr_t holds any valid DMA address. If the DMA API only uses 32/64-bit
addresses, dma_addr_t need only be 32/64 bits wide.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Added support for timer_early_get_count() and timer_early_get_rate()
This is mostly useful in tracing.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
When tracing functions is enabled this adds calls to
__cyg_profile_func_enter() and __cyg_profile_func_exit() to the traced
functions.
__cyg_profile_func_enter() and __cyg_profile_func_exit() invoke
timer_get_us() to record the entry and exit time.
initr_dm() will make gd->dm_root = NULL and gd->timer = NULL, so
timer_get_us() -> get_ticks() -> dm_timer_init() will lead to an
indefinite recursion.
So select TIMER_EARLY when tracing got enabled.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.
This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
fit_print_contents prints similar fit information as printed in bootm stages.
Removing this API reduces redundancy & provides improvement in boottime.
Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change 2 typo error in CONFIG_LIB_ELF description:
- Supoort => Support
- fir => for
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a unit test for printing via pr_err() and pr_cont().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
With commit d094a0734c ("log: allow for message continuation") we have
defined a special log level and category for message continuation. Let's
have a macro for using these.
If logging is enabled log_cont() will create a continuation log output with
the same logging level and category as the previous message.
If logging is not enabled, log_cont() will print like printf().
Provide macros for logging levels LOG_EMERG, LOG_ALERT, LOG_CRIT.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change debug_cond() such that it can be used instead of a function like
debug().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The macro BIT_MASK is already defined in include/linux/bitops.h. To avoid
name collisions rename BIT_MASK() in drivers/ram/k3-j721e/lpddr4_private.h
to LPDDR4_BIT_MASK().
Remove superfluous parantheses.
Remove superfluous comparison to 0.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
log.h and dm/devres.h are U-Boot includes. So placing them
behind #ifndef __UBOOT__ does not make any sense.
Fixes: f7ae49fc4f ("common: Drop log.h from common header")
Fixes: 61b29b8268 ("dm: core: Require users of devres to include the header")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building fails with DEBUG=1:
lib/aes.c: In function ‘debug_print_vector’:
lib/aes.c:622:45: error:
cast from pointer to integer of different size
[-Werror=pointer-to-int-cast]
622 | printf("%s [%d] @0x%08x", name, num_bytes, (u32)data);
Pointers can only be cast to (uintptr_t). But anyway we have
%p for printing pointers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
obj-$(CONFIG_$(SPL_TPL_)YMODEM_SUPPORT) += xyzModem.o is there,
no need obj-$(CONFIG_SPL_YMODEM_SUPPORT) += xyzModem.o
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make it more obvious what .dts file was expected by the build system.
When adding support for a new board, I kept getting this error message,
assuming I passed a wrong DEVICE_TREE parameter.
However, what was really the mistake was that the entry in
`arch/arm/dts/Makefile` was missing, and u-boot didn't like not being
able to find the .dtb file that should have been produced.
Simply logging the expected .dtb file name should make it easier to spot
such mistakes.
Signed-off-by: Florian Klink <flokli@flokli.de>
When ESC/CTRL+C is pressed interrupt bootmenu and jump into U-Boot console.
As the last entry in bootmenu is always U-Boot console just choose the last
entry when ESC or CTRL+C is pressed.
ESC key is detected when either no other character appears after '\e'
within 10ms or when non-'[' appears after '\e'.
It is useful when bootmenu is part of boot process and you want to
interrupt boot process by scripts which control U-Boot (serial) console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
A common use of memmove() can be handled by memcpy(). Also memcpy()
includes an optimization for large sizes: it copies a word at a time. So
we can get a speed-up by calling memcpy() to handle our move in this case.
Update memmove() to call also memcpy() if the source don't overlap
the destination (src + count <= dest).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
U-Boot DM model probe only single device at a time
which is enabled and configured using device tree
or platform data method.
PL011 UART IP is SBSA compliant and firmware does the
serial port set-up, initialization and let the kernel use
UART port for sending and receiving characters.
Normally software talk to one serial port time but some
LayerScape platform require all the UART devices enabled
in Linux for various use case.
Adding support to probe all enabled serial devices like SBSA
compliant PL011 UART ports probe and initialization by firmware.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Support a common method to probe all devices associated with uclass.
This includes data structures and code for finding the first device and
looping for remaining devices associated with uclasses (groups of devices
with the same purpose, e.g. all SERIAL ports will be in the same uclass).
An example is SBSA compliant PL011 UART IP, where firmware does the serial
port initialization and prepare uart device to let the kernel use it for
sending and reveiving the characters.SERIAL uclass will use this function
to initialize PL011 UART ports.
The feature is enabled with CONFIG_DM.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Remove the #if 0 present since the first version of console.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With our optimization settings the linker eliminates unused functions.
But for debugging it is better to compile with -Og or -O0. With -O0
compiling the sandbox fails due to the missing function fixup_cmdtable()
called by dm_reloc() and others.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the hash check fails on a loadable image, the SPL/TPL simply
jump to the next one. This commit changes this behaviour, when the
hash check fails on a loadable image, the function spl_load_simple_fit
stops and report an error.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There should be no need to insert non-printable characters
and this prevents line editing getting confused.
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Adds an optional SALT value to AUTOBOOT_STOP_STR_SHA256. If a string
followed by a ":" is prepended to the sha256, the portion to the left
of the colon will be used as a salt and the password will be appended
to the salt before the sha256 is computed and compared.
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Joel Peshkin <joel.peshkin@broadcom.com>
To: u-boot@lists.denx.de
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The previous patch made the table look bad. Fix it, and leave some
space for a future element being a bit longer than the current
maximum.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
When setting aside a GPT partition for holding the U-Boot environment,
having a partition type GUID [1] indicating "Linux filesystem" (as
most tools default to) is somewhat misleading - and there's no other
well-known type GUID that is better suited. So to have a canonical
value to put into the type field, define
3de21764-95bd-54bd-a5c3-4abe786f38a8
to mean a partition holding a U-Boot environment.
This is a v5 namespace-name GUID [2], generated [3] from a namespace
of "25cbcde0-8642-47c6-a298-1a3a57cd256b" and name "U-Boot
environment".
Should future type GUIDs be defined in the context of U-Boot, it's
sensible to use that same namespace GUID.
[1] https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
[2] https://en.wikipedia.org/wiki/Universally_unique_identifier#Versions_3_and_5_(namespace_name-based)
[3] https://www.uuidtools.com/v5
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There's no reason to require an appropriately sized output parameter
for the string, that's error-prone should the table ever grow an
element with a longer string. We can just return the const char*
pointer directly.
Update the only caller accordingly, and get rid of pointless ifdeffery
in the header so that the compiler always sees a declaration and can
thus do type-checking, whether or not PARTITION_TYPE_GUID is enabled
or not.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
power/regulator will not be built if just CONFIG_SPL_DM_REGULATOR is
enabled. It needs CONFIG_SPL_POWER_SUPPORT to be enabled as well.
For example, if we just need a GPIO regulator in SPL:
CONFIG_DM_REGULATOR=y
CONFIG_SPL_DM_REGULATOR=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPL_DM_REGULATOR_GPIO=y
Will not suffice, since the entire regulator build for SPL depends on
CONFIG_SPL_POWER_SUPPORT. Elaborate that information in the Kconfig
dependency.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Align the prefix used in cmd_ut_category function and name of tests
for ut str.
This patch solves the issues detected by "make qcheck" after previous
patch.
Fixes: fdc79a6b12 ("lib: Add a function to convert a string to upper case")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the prefix used in cmd_ut_category function and name of tests
for ut mem.
This patch solves the issues detected by "make qcheck" after previous
patch.
Fixes: 550a9e7902 ("cmd: Update the memory-search command")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This test cannot work unless CONFIG_BLOBLIST is enabled. Update it to add
that condition.
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This tests assumes it is running on sandbox. Add a few functions to handle
silencing the console on any board and use those instead.
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add eMMC and GPT support.
- GPT partition list and command to create the GPT added to u-boot
environment
- eMMC boot commands added to u-boot environment
- new gpt commands (enumarate and setenv) that are used by broadcom
update scripts and boot commands
- eMMC specific u-boot configurations with environment saved in eMMC
and GPT support
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
[trini: Make gpt_setenv initialize ret to -1, given relevant return
error values]
Signed-off-by: Tom Rini <trini@konsulko.com>
During build of simple panel driver backlight is needed so let's enable
it:
aarch64-linux-gnu-ld.bfd: drivers/built-in.o: in function `simple_panel_set_backlight':
u-boot/drivers/video/simple_panel.c:43: undefined reference to `backlight_set_brightness'
aarch64-linux-gnu-ld.bfd: drivers/built-in.o: in function `simple_panel_enable_backlight':
u-boot/drivers/video/simple_panel.c:28: undefined reference to `backlight_enable'
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
The tests in test/lib/test_print.c fail without CONFIG_CONSOLE_RECORD=y.
Add a build dependency.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>