The ClearFog Base boot from UART when setting the DIP switches to 01001.
Unfortunately, the SPL code sometimes fails to detect the UART boot
method at run-time. Add an alternative SAR UART boot value to fix this.
Note that this alternative value is not documented (Armada 38x Hardware
Specifications, Table 48). But experimentations showed it on the
ClearFog Base.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
dram_ecc_scrubbing() had code to skip unused DRAM banks but it would not
work because mvebu_sdram_bs() returns 0 and the code was subtracting 1
before checking the size. Remove the -1 from the bank size and the +1
from the total which will skip unused banks and still calculate the
correct size. Put the -1 where it is needed for scrubbing via the xor
engine.
Reported-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Armada-38x has 1.8GHz and 2.0GHz variants. Add entries for these
variants to the sar_freq_tab.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Display more information about the current RAM configuration. With these
changes the output on a 88F6820 board is
SoC: MV88F6820-A0 at 1600 MHz
DRAM: 2 GiB (800 MHz, 32-bit, ECC not enabled)
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
These SoCs are network packet processors (switch chips) with integrated
ARMv7 cores. They share a great deal of commonality with the Armada-XP
CPUs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, we support 2 "theadorable" MVEBU build targets. One with a
stripped down configuration (theadorable) and one with a full blown
configuration (theadorable_debug), including PCI, ethernet etc. When
we introduced these configs, the plan was to remove the debug version
at some point. But now it seems better to keep the full-blown version
and remove the "non-debug" version instead.
At a later stage, I will rename the remaining "theadorable_debug"
target into a more fitting one.
Signed-off-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
In some of the QSPI controller version, there must be atleast
128bit data available in TX FIFO for any pop operation otherwise
error bit will be set. The code will not make any behavior change
for previous controller as the transfer data size in ipcr register
is still the same.
Patch is tested on LS1046A which do not require 16 bytes aligned and
LS1088A which require 16 bytes aligned data in TX FIFO
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Anupam Kumar <anupam.kumar_1@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Spansion S25FS256S and S25FL256S flashes have equal JEDEC ID and ext ID.
As far as S25FL256S occures in spi_flash_ids before S25FS256S, U-Boot
incorrectly detects FS flash as FL. Thus its better to compare with
S25FS256S first.
Signed-off-by: Vsevolod Gribov <vgribov@larch-networks.com>
[Added S-o-b]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The flash chip is 2 MiB , organized as 32 x 64 kiB sectors .
Rectify the entry to match the datasheet, reality and Linux SNOR IDs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add MT35XU512ABA1G12 parameters to NOR flash parameters array.
The MT35XU512ABA1G12 only supports 1 bit mode and 8 bits. It can't support
dual and quad. Supports subsector erase with 4KB granularity, have support
of FSR(flag status register) and flash size is 64MB.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is recommended to check either controller is free to take
new spi action. The IP_ACC and AHB_ACC bits indicates that
the controller is busy in IP or AHB mode respectively.
And the BUSY bit indicates that controller is currently
busy handling a transaction to an external flash device
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add driver model support for mxc spi driver.
Most functions are restructured to be reused by DM and non-DM.
Tested on mx6slevk/mx6qsabresd board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
In some cases, such as FreeBSD, the path to an alternative dtc needs to
be used. Rather than override the one given in the Makefile on the
command line, make this part of the build configuration.
Signed-off-by: Tom Rini <trini@konsulko.com>
This makes us act like the Linux Kernel does and allow for dtc to be
provided externally but otherwise we use the version of dtc that is
included in the sources. This in turn means that we can drop the
checkdtc logic. We select DTC in the cases where we will need the dtc
tool provided.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds the following commits from upstream:
fe50bd1ecc1d fdtget: Split out cell list display into a new function
62d812308d11 README: Add a note about test_tree1.dts
5bed86aee9e8 pylibfdt: Add support for fdt_subnode_offset()
46f31b65b3b3 pylibfdt: Add support for fdt_node_offset_by_phandle()
a3ae43723687 pylibfdt: Add support for fdt_parent_offset()
a198af80344c pylibfdt: Add support for fdt_get_phandle()
b9eba92ea50f tests: Return a failure code when any tests fail
155faf6cc209 pylibfdt: Use local pylibfdt module
50e5cd07f325 pylibfdt: Add a test for use of uint32_t
ab78860f09f5 pylibfdt: Add stdint include to fix uint32_t
36f511fb1113 tests: Add stacked overlay tests on fdtoverlay
1bb00655d3e5 fdt: Allow stacked overlays phandle references
a33c2247ac8d Introduce fdt_setprop_placeholder() method
0016f8c2aa32 dtc: change default phandles to ePAPR style instead of both
e3b9a9588a35 tests: fdtoverlay unit test
42409146f2db fdtoverlay: A tool that applies overlays
aae22722fc8d manual: Document missing options
13ce6e1c2fc4 dtc: fix sprintf() format string error, again
d990b8013889 Makefile: Fix build on MSYS2 and Cygwin
51f56dedf8ea Clean up shared library compile/link options
21a2bc896e3d Suppress expected error message in fdtdump test
2a42b14d0d03 dtc: check.c fix compile error
a10cb3c818d3 Fix get_node_by_path string equality check
548aea2c436a fdtdump: Discourage use of fdtdump
c2258841a785 fdtdump: Fix over-zealous version check
9067ee4be0e6 Fix a few whitespace and style nits
e56f2b07be38 pylibfdt: Use setup.py to build the swig file
896f1c133265 pylibfdt: Use Makefile constructs to implement NO_PYTHON
90db6d9989ca pylibfdt: Allow setup.py to operate stand-alone
e20d9658cd8f Add Coverity Scan support
b04a2cf08862 pylibfdt: Fix code style in setup.py
1c5170d3a466 pylibfdt: Rename libfdt.swig to libfdt.i
580a9f6c2880 Add a libfdt function to write a property placeholder
ab15256d8d02 pylibfdt: Use the call function to simplify the Makefile
9f2e3a3a1f19 pylibfdt: Use the correct libfdt version in the module
e91c652af215 pylibfdt: Enable installation of Python module
8a892fd85d94 pylibfdt: Allow building to be disabled
741cdff85d3e .travis.yml: Add builds with and without Python library prerequisites
14c4171f4f9a pylibfdt: Use package_dir to set the package directory
89a5062ab231 pylibfdt: Use environment to pass C flags and files
4e0e0d049757 pylibfdt: Allow pkg-config to be supplied in the environment
6afd7d9688f5 Correct typo: s/pylibgfdt/pylibfdt/
756ffc4f52f6 Build pylibfdt as part of the normal build process
8cb3896358e9 Adjust libfdt.h to work with swig
b40aa8359aff Mention pylibfdt in the documentation
12cfb740cc76 Add tests for pylibfdt
50f250701631 Add an initial Python library for libfdt
cdbb2b6c7a3a checks: Warn on node name unit-addresses with '0x' or leading 0s
4c15d5da17cc checks: Add bus checks for simple-bus buses
33c3985226d3 checks: Add bus checks for PCI buses
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds the following commits from upstream:
558cd81bdd43 dtc: Bump version to v1.4.4
c17a811c62eb fdtput: Remove star from value_len documentation
194d5caaefcb fdtget: Use @return to document the return value
d922ecdd017b tests: Make realloc_fdt() really allocate *fdt
921cc17fec29 libfdt: overlay: Check the value of the right variable
9ffdf60bf463 dtc: Simplify asm_emit_string() implementation
881012e44386 libfdt: Change names of sparse helper macros
bad5b28049e5 Fix assorted sparse warnings
672ac09ea04d Clean up gcc attributes
49300f2ade6a dtc: Don't abuse struct fdt_reserve_entry
Signed-off-by: Tom Rini <trini@konsulko.com>
Using the update-dtc-source.sh script from Linux v4.14-rc1 import the
portions of dtc that we require. We bring in update-dtc-source.sh and
scripts/dtc/Makefile from Linux v4.14-rc1. Rework DTC_FLAGS handling to
not require a test.
Signed-off-by: Tom Rini <trini@konsulko.com>
For EFI boot GPT partition table support is needed as well
as the part command and also the SPL needs to fallback to
other boot methods after parse the SPL header.
Signed-off-by: Frank Kunz <mailinglists@kunz-im-inter.net>
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the
NAND initialization process is driven by the driver itself.
CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PPA loading during SPL stage is not required for nornal
SD boot scenario.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PPA loading during SPL stage is not required for nornal
SD boot scenario.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Current u-boot disables IFC support for SD boot on all ls1043a
boards. Actually IFC only conflicts with QSPI on ls1043a hardware.
Only when QSPI is used, IFC should be disabled. Otherwise,
the u-boot with ls1043aqds_sdcard_ifc_defconfig would not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per current implementation, default value of board env is
based on board filename i.e ls2080ardb.
With distro support changes, this env is used to decide upon
kernel dtb which is different for other SoCs (ls2088a, ls2081a)
combination supported with this board.
Add support to modify board env at runtime based on SoC type
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For most of ls2080ardb use-cases, mc private DRAM block is required
to be of 1.75GB.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: this reservation needs to be reduced if memory is not enough]
Reviewed-by: York Sun <york.sun@nxp.com>
Commit 0aaa1a9 added support for LS208xA devices but fixing
iommu-map property is missing. This patch adds support for
fixing iommu-map.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_DISPLAY_BOARDINFO_LATE config is used to delay
the prints of boardinfo late in cycle during uboot boot.
This feature is not required in case of QSPI_BOOT.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not necessary for every SoC to have 2 SATA controller.
So put SATA1, SATA2 code under respective defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1
IO cells. Without this bias voltage these I/O cells can not function
properly. The PBIAS cell is controlled by software.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dev_read_string_count() is used to get the number of strings in a
stringlist.
dev_read_string_index() is used to get a string in the stringlist based on
its position in the list.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add OF match entries and quirks for Renesas RCar Gen3 controllers
into the driver. The IP this driver handles is in fact Matsushita
one and in used both in Socionext and Renesas chips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Check if the OF match has any associated data and if so, use those
data as the controller quirks, otherwise fallback to the old method
of reading the controller version register to figure out the quirks.
This allows us to supply controller quirks on controllers which ie.
do not have version register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita. This patch adds support for handling of the 64bit
FIFO on this controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita, yet the register addresses are shifted by 1 to the
left. The whole controller is also 64bit, including the data
FIFOs and RSP registers. This patch adds support for handling
the register IO by shifting the register offset by 1 in the IO
accessor functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
This patch prepares the driver to support controller(s) with registers
at locations shifted by constant. Pull out the readl()/writel() from
the driver into separate functions, where the adjustment of the register
offset can be easily contained.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
With support for overlays and calling the -@ flag to dtc we need to have
at least 1.4.3 available now.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
common/spl/spl_fit.c:201:12: warning: passing argument 4 of ‘gunzip’
from incompatible pointer type [-Wincompatible-pointer-types]
src, &length))
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Jean-Jacques Hiblot <jjhiblot@ti.com>
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>