We want to check the result of musb_init_controller
and not the address were the result is stored.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
'A || (!A && B)' is equivalent to 'A || B'.
Let's reduce the complexity of the statement in start_jr0().
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After allocating sata->cmd_hdr_tbl_offset we have to check
this variable and not variable sata.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
(pdimm[0].data_width >= 32) || (pdimm[0].data_width <= 40)
is always true.
We should use && here.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The number of arguments for printf does not match the
format string.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If current_urb is NULL it should not be dereferenced.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.
The arm-smccc is supported on ARMv7 or later. Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31. In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Depending on DDR configuration, gcc-6.x will show up unused-const-
variable messages. Use __maybe_unused specifier for all dynamic_odt
variable definitions to remove these warnings.
Memory footprint will not increase as gcc will optimize out unused
constants.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: York Sun <york.sun@nxp.com>
To enable mipi display, we need to enable pmic
rk808 first for lcd3v3 power,which use i2c0 to
communicate with soc. So enable i2c0.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The warm-reset of rk3188 socs keeps the remap setting as it was, so if
it was enabled, the cpu would start from address 0x0 of the sram instead
of address 0x0 of the bootrom, thus making the reset hang.
Therefore make sure the remap is disabled before attempting a warm reset.
Cold reset is not affected by this at all.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Allow LEDs to be blinked if the driver supports it. Enable this for
sandbox so that the tests run.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
Add support for toggling an LED into the uclass interface. This can be
efficiently implemented by the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
It is useful to be able to read the LED as well as write it. Add this to
the uclass and update the GPIO driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
At present this is very simple, supporting only on and off. We want to
also support toggling and blinking. As a first step, change the name of
the main method and use an enum to indicate the state.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
These structures are normally named with 'uc' instead of 'uclass'. Change
this one for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
There should be a blank line between each option. Add one before LED_GPIO.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
We should invalidate the dcache before starting the DMA. In case there are
any dirty lines from the DMA buffer in the cache, subsequent cache-line
replacements may corrupt the buffer in memory while the DMA is still going on.
Cache-line replacement can happen if the CPU tries to bring some other memory
locations into the cache while the DMA is going on.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Merely using dma_alloc_coherent does not ensure that there is no stale
data left in the caches for the allocated DMA buffer (i.e. that the
affected cacheline may still be dirty).
The original code was doing the following (on AArch64, which
translates a 'flush' into a 'clean + invalidate'):
# during initialisation:
1. allocate buffers via memalign
=> buffers may still be modified (cached, dirty)
# during interrupt processing
2. clean + invalidate buffers
=> may commit stale data from a modified cacheline
3. read from buffers
This could lead to garbage info being written to buffers before
reading them during even-processing.
To make the event processing more robust, we use the following sequence
for the cache-maintenance:
# during initialisation:
1. allocate buffers via memalign
2. clean + invalidate buffers
(we only need the 'invalidate' part, but dwc3_flush_cache()
always performs a 'clean + invalidate')
# during interrupt processing
3. read the buffers
(we know these lines are not cached, due to the previous
invalidation and no other code touching them in-between)
4. clean + invalidate buffers
=> writes back any modification we may have made during event
processing and ensures that the lines are not in the cache
the next time we enter interrupt processing
Note that with the original sequence, we observe reproducible
(depending on the cache state: i.e. running dhcp/usb start before will
upset caches to get us around this) issues in the event processing (a
fatal synchronous abort in dwc3_gadget_uboot_handle_interrupt on the
first time interrupt handling is invoked) when running USB mass
storage emulation on our RK3399-Q7 with data-caches on.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dwc3_flush_cache() call was declared and used inconsistently:
* The declaration assumed 'int' for addresses (a potential issue
when running in a LP64 memory model).
* The invocation cast the address to 'long'.
This change ensures that both the declaration and usage of this
function consistently uses 'uintptr_t' for correct behaviour even
when the allocated buffers (to be flushed) reside outside of the
lower 32bits of memory.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Both these numbers are calculated in runtime and dynamically assigned
to the device descriptor during bind().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't want to claim that we support a serial number string and
later return nothing. Because of that, if g_dnl_serial is an empty
string, let's skip setting iSerialNumber to a valid number.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A USB String descriptor can be up to 255 characters long and it's not
NULL terminated according to the USB spec. This means our
MAX_STRING_SERIAL should be 256 (to cope with NULL terminator).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After enabling log printing to lcd, when the screen starts
scrolling, system crashes. Log is shown as bellow:
"Synchronous Abort" handler, esr 0x96000045
"Synchronous Abort" handler, esr 0x96000045
Checking the source code, we found that the variable "pixels"
gets a wrong value:
int pixels = VIDEO_FONT_HEIGHT * vid_priv->line_length;
"pixels" here means the value of pixels for a character, rather
than the bytes for a character. So the variable "pixels" is 4
times bigger than it's exact value, which will cause the memory
overflow when the cpu runs the following code:
for (i = 0; i < pixels; i++)
*dst++ = clr; <<----
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Some board do not use the dwc2 internal VBUS_DRV signal, but
use a gpio pin to enable the 5.0V VBUS power, add interface to
enable the power in dwc2 driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add common widescreen modes 800x480 and 1024x600.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
DCU_LAYER_MAX_NUM is currently used for DCU_MODE_BLEND_ITER and it
actually overflows the maximum value of BLEND_ITER for Vybrid and
LS102XA. Fix this by using a default value of 2.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
When enabling the DCU and pixel clock, the test mode is activated
since this is the reset configuration. The test mode immediately
shows a red screen on a LCD. A moment later, the DCU gets
initialized properly.
This patch enables the pixel clock after initialization of the DCU
control register. This avoids this initial flicker on LCD screens.
While at it change the polarity of pixel clock to display samples
data on the rising edge.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Fix the framebuffer location to the very end of the available memory.
This allows to remove the area from available memory for the kernel,
which in turn allows to display the splash screen through the Linux
kernel boot process.
Ideas has been taken from the sunxi display driver, e.g.
20779ec3a5 ("sunxi: video: Dynamically reserve framebuffer memory")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
sdhci_transfer_data() function transfers the blocks passed up to the
number of blocks defined in mmc_data, but returns immediately once all
the blocks are transferred, even if the loop exit condition is not met
(bit SDHCI_INT_DATA_END set in the STATUS word).
When doing multiple writes to mmc, returning right after the last block
is transferred can cause the write to fail when sending the
MMC_CMD_STOP_TRANSMISSION command right after the
MMC_CMD_WRITE_MULTIPLE_BLOCK command, leaving the mmc driver in an
unconsistent state until reboot. This error was observed in the rpi3
board.
This patch waits for the SDHCI_INT_DATA_END bit to be set even after
sending all the blocks.
Test: Reliably wrote 2GiB of data to mmc in a rpi3.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The linux kernel driver for this module does not use a delay when
writing to the SDHCI_BUFFER register. This patch mimics that behavior
in order to speed up the mmc writes on the Raspberry Pi.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the driver model support for Atmel mci while retaining the
existing legacy code. This allows the driver to support boards
that have converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Add the clock support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add the device tree support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>