* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
The current implementation of debug doesn't play well with GCC4.6.
This implementation also fixes GCC4.6 complaints about unused variables
while maintaining code size.
Also, drop the debugX() as that's not used anywhere anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
lcd.c: In function 'lcd_setmem':
lcd.c:446:2: warning: format '%d' expects type 'int', but argument 2 has type
'u_long'
lcd.c:446:2: warning: format '%d' expects type 'int', but argument 3 has type
'u_long'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
interrupts.c: In function 'interrupt_init_cpu':
interrupts.c:37: warning: implicit declaration of function 'GTREGREAD'
interrupts.c:37: error: 'LOW_INTERRUPT_CAUSE_REGISTER' undeclared (first use in
this function)
interrupts.c:37: error: (Each undeclared identifier is reported only once
interrupts.c:37: error: for each function it appears in.)
interrupts.c:37: error: 'HIGH_INTERRUPT_CAUSE_REGISTER' undeclared (first use in
this function)
interrupts.c:40: error: 'ETHERNET0_INTERRUPT_CAUSE_REGISTER' undeclared (first
use in this function)
interrupts.c:40: error: 'ETHERNET1_INTERRUPT_CAUSE_REGISTER' undeclared (first
use in this function)
interrupts.c:40: error: 'ETHERNET2_INTERRUPT_CAUSE_REGISTER' undeclared (first
use in this function)
interrupts.c:44: error: 'ETHERNET0_INTERRUPT_MASK_REGISTER' undeclared (first
use in this function)
interrupts.c:44: error: 'ETHERNET1_INTERRUPT_MASK_REGISTER' undeclared (first
use in this function)
interrupts.c:44: error: 'ETHERNET2_INTERRUPT_MASK_REGISTER' undeclared (first
use in this function)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
cmd_date.c: In function ‘do_date’:
cmd_date.c:50:6: warning: variable ‘old_bus’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
This renames BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT.
Along the way it removes some leftover
#define BOARD_LATE_INIT 1
and adds some basic documentation for board specific
callbacks in README.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
Commit 476af29 broke this check when the ifdef lists we consolidated.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The rarp code includes another instance of the auto_load logic, so call
what is now net_auto_load() instead.
This also fixes an incorrect call to TftpStart() which was never seen
since apparently no boards enable rarp.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Add basic support for Calxeda Highbank platform. Only minimal support with
serial and SATA are included.
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM
as they are no longer needed with the support for more than 1 PHYs in davinci
emac driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Since commit f1d2b313c9 the serial
port of the da850evm is accessed before the UART2 peripheral of
the SoC is powered on in the function board_init() in
board/davinci/da8xxevm/da850evm.c.
When u-boot is used in conjunction with the UBL (user boot loader, see
doc/README.davinci) on this board, the UART2 peripheral is already
turned on by UBL at the time u-boot is started. Hence, the wrong
initialization sequence is not noticed by most users. However, if UBL is not
used, u-boot must power on the peripheral before using it.
This patch adds a board_early_init_f() function for the LPSC
configuration to the da850evm board configuration.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This allows the user can easily add extra kernel arguments. Very helpful
for reserving memory for the DSP without rewriting the entire kernel
argument line.
Signed-off-by: Philip Balister <philip@opensdr.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Starting with kernel 2.6.37, the serial ports on the OMAP3 are called
ttyOX, not ttySX.
Signed-off-by: Philip Balister <philip@opensdr.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add support for enabling NAND boot mode in configuration file and
add correspanding pinmux support, nand initialize function in board file.
The size required for environment variables not more than 10KB
the CONFIG_ENV_SIZE is set to 10KB from (512 << 10).
Acked-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
revert commit 98c19aff95 as the
disabling of cache need not be done explicitly. Subsequent
patches to new cache management framework has fixed it.
EMAC issue with cache coherency still exists when cahces are
enabled.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
revert commit 913a39e9aa as the
disabling of cache need not be done explicitly. Subsequent
patches to new cache management framework has fixed it.
EMAC issue with cache coherency still exists when cahces are
enabled.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
With malloc support being a new requirement for all ARM SPL
implementations, define a small area for use on devkit8000.
Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
FAT library now uses malloc() and free(). But SPL doesn't
have heap until now. Setup a heap in SDRAM to fix this issue.
However this increases SPL footprint beyond the available SRAM
budget. So, compile out some fancy features in the SDARM init
bring back footprint under control
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
All ddr configurations(geometry/timings) are done automatically
by detecting the device connected at run time. Though this
is a useful feature, making this as a default setting increases
the code size by about 2K bytes. This is quite big, especially
in the case of SPL which runs from a smaller SRAM. So do not
use this feature as the default setting, instead use the
precalculated tables.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to
the definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Copied wholeheartedly from board/Marvell/guruplug and modified to add support
for SPI NOR flash.
CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's
kernel.org tree adds it to mach-types.h. Once it trickles down, the definition
can be removed from include/configs/dreamplug.h.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Enable support for new PMIC driver at GONI reference target.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
This commit adds support for MAX8998 PMIC driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
I2C or SPI PMIC devices can be accessed.
Separate files: pmic_i2c.c and pmic_spi.c are responsible
for handling transmission over I2C or SPI bus.
New flags:
CONFIG_PMIC - enable PMIC general device.
CONFIG_PMIC_I2C/SPI - specify the interface to be used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
In some cases, saving data in RAM as a file with FAT format is required.
This patch allows the file to be written in FAT formatted partition.
The usage is similar with reading a file.
First, fat_register_device function is called before file_fat_write function
in order to set target partition.
Then, file_fat_write function is invoked with desired file name,
start ram address for writing data, and file size.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This library provides useful functions to drivers which want to use
the fdt to control their operation. Functions are provided to:
- look up and enumerate a device type (for example assigning i2c bus 0,
i2c bus 1, etc.)
- decode basic types from the fdt, like addresses and integers
While this library is not strictly necessary, it helps to minimise the
changes to a driver, in order to make it work under fdt control. Less
code is required, and so the barrier to switch drivers over is lower.
Additional functions to read arrays and GPIOs could be made available
here also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This new option allows U-Boot to embed a binary device tree into its image
to allow run-time control of peripherals. This device tree is for U-Boot's
own use and is not necessarily the same one as is passed to the kernel.
The device tree compiler output should be placed in the $(obj)
rooted tree. Since $(OBJCOPY) insists on adding the path to the
generated symbol names, to ensure consistency it should be
invoked from the directory where the .dtb file is located and
given the input file name without the path.
This commit contains my entry for the ugliest Makefile / shell interaction
competition.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a better name for this protocol. Also remove the typedef to keep
checkpatch happy, and move zeroing of NetBootFileXferSize a little
earlier since TFTPPUT will need to change this.
Signed-off-by: Simon Glass <sjg@chromium.org>
