Commit Graph

58308 Commits

Author SHA1 Message Date
Bhargav Shah
05e35d4297 mmc: mmc_spi: Re-write driver using DM framework
This patch rewrites MMC SPI driver using U-Boot DM
framework and get it's working on SiFive Unleashed
board.

Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15 10:16:49 +08:00
Anup Patel
f49ff79935 mmc: skip select_mode_and_width for MMC SPI host
The MMC mode and width are fixed for MMC SPI host hence we skip
sd_select_mode_and_width() and mmc_select_mode_and_width() for
MMC SPI host.

Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
0538477c53 mmc: retry a few times if a partition switch failed
This operation may fail. Retry it a few times before giving up and report
a failure.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
9bc5666c8a mmc: do not change mode when accessing a boot partition
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
bb98b8c5c0 mmc: During a switch, poll on dat0 if available and check the final status
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
513e00b64e mmc: When switching partition, use the timeout specified in the ext_csd
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
39320c537d mmc: use the generic timeout for cmd6 (SWITCH) provided in the ext_csd
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.

Following Linux Kernel code, the timeout also changed from 1000 -> 500

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
cd0b80ec9c mmc: if possible, poll the busy state using DAT0
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.

Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
863d10044a mmc: add mmc_poll_for_busy() and change the purpose of mmc_send_status()
mmc_send_status() is currently used to poll the card until it is ready, not
actually returning the status of the card.
Make it return the status and add another function to poll the card.

Also remove the 'extern' declaration in the mmc-private.h header to comply
with the coding standard.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
c2c22b9df3 mmc: omap_hsmmc: provide wait_dat0 even if UHS modes are not supported
This function can also be used for eMMC devices.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
c5bda37589 Revert "mmc: Add a new callback function to perform the 74 clocks cycle sequence"
This reverts commit 318a7a576b.

The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
db52e19ced mmc: omap_hsmmc: don't fill the send_init_stream callback
This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
b2ffa3320a mmc: omap_hsmmc: reset FSM for DAT and CMD lines if needed before a new command
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA

Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Akio Hirayama
24b1e0c7e2 mmc: rpmb: fix response type of CMD25
The response type of CMD25 is R1 instead of R1b.

Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
da18c62b6e mmc: sdhci: Implement SDHCI card detect
Card detect function implemented for SDHCI framework.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
451931ea70 mmc: sdhci: Read cd-gpio from devicetree
This patch reads cd-gpio property from devicetree

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
86a94e7b2b mmc: Read sd card detect properties from DT
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
e3a14b6684 mmc: mvebu: Remove unused MMC_CAP.. macros
Removed MMC_CAP_NONREMOVABLE, MMC_CAP_NEEDS_POLL macros from
mvebu_mmc.h to avoid redefining of these macros when compiled with
mvebu based configs.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-15 10:16:49 +08:00
Tom Rini
a9a3a37f92 - syscon: add support for power off
- stm32mp1: add op-tee config
 - stm32mp1: add specific commands: stboard and stm32key
 - add stm32 mailbox driver
 - solve many stm32 warnings when building with W=1
 - update stm32 gpio driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdKK2iAAoJEOKyvdngqpN1TvcH/jj1ujNdRKn994R3DqULzFtc
 Y0WGjAciTUuV0d9gZLxPZJwlWfqxLgbmUEBlPJQJe79gaM7kNN0PgAe6GNedFhGk
 UhRR7GgbA7wogorpRo8aLe3XYEqHtgPFkf1nSiNz/AHLBg8SB20VhWcY90Kha9lh
 IJ0GK+lSdCxiyaLBC2nswnI2PS/fl4NfC7KWvujtKZduIDIOHqh5q+39llpejyuw
 WOzL/bEa4ald6JKpxOii2KXNwD1gUDQGmPzADYcIdwzJtx9hft7DBSLC5Nr+ndBz
 72TjpbtfJ/qIurv8HeXYs9mtwnCO3WP+015fog0T0zjZ48BrT1A8C96ezwLOfz0=
 =W3ny
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20190712' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
2019-07-14 09:09:49 -04:00
Tom Rini
6070ef409c Merge branch '2019-07-12-master-imports'
- First round of TI Davinci updates
- Some OMAP3 DM updates
- Other misc updates
2019-07-14 09:05:20 -04:00
Tom Rini
ae8d23a668 test: Disable pci_ep test for now
This test is currently broken so disable it for now.

Cc: Ramon Fried <ramon.fried@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-13 21:18:37 -04:00
Adam Ford
550eebcfb4 ARM: dts: logicpd som-lvs and torpedos: Shrink SPL DTB
Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13 11:11:31 -04:00
Sven Schwermer
1164c546d5 regulator: Allow autosetting fixed regulators
Fixed regulators don't have a set_value method. Therefore, trying to
set their value will always return -ENOSYS.

Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-13 11:11:31 -04:00
Heiko Schocher
5fc7cf8c8e gpio: add gpio-hog support
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.

for more infos see:
doc/device-tree-bindings/gpio/gpio.txt

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-13 11:11:30 -04:00
Adam Ford
42f1539727 ARM: dts: logicpd-som-lv: Resync with Kernel 5.1.9
The MMC card-detect pin was incorrectly defined which was fixed.
This patch resync's the dts and removes the u-boot specific fix.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13 11:11:30 -04:00
Adam Ford
4972a2a83f ARM: dts: da850: Resync with Linux 5.1.9
The da850.dtsi file had some changes.  This patch pulls in the
changes from Kernel 5.1.9

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13 11:11:30 -04:00
Adam Ford
877ab2423b ARM: davinci: da850: Manual pinmux only when PINCTRL not available
With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL).  If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away.  This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13 11:11:29 -04:00
Adam Ford
159a887e74 pinctrl: pinctrl-single: Add 'pinctrl-single, bits' support
The TI Davinci (da850/l138/am1808) use pinctrl-single,bits for
pinmuxing peripherals.  This patch allosw the pinctrl-single
driver to parse the pinctrl-single,bits options and correctly
setup devices.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13 11:11:29 -04:00
Tom Rini
2a51e16bd5 configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support.  Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.

To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol.  Finally, in
the case of a few boards we really do need the full printf
functionality.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-13 11:11:29 -04:00
Keerthy
28115e7bac power: regulator: Kconfig: Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565
Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the regulator support in SPL.

Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-07-13 11:11:29 -04:00
Keerthy
2463874883 power: pmic: Kconfig: Add SPL_PMIC configs for palmas/lp873x/lp87565
Add SPL_PMIC configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the pmics in SPL.

Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-07-13 11:11:28 -04:00
Niel Fourie
6e171b661e ARM: am335x: Add phyCORE AM335x R2 support
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.

CPU  : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
eth0: ethernet@4a100000

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART
 - USB (host)

Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")

Signed-off-by: Niel Fourie <lusus@denx.de>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Marek Vasut <marex@denx.de>
2019-07-13 11:11:28 -04:00
David Lechner
1d259e4d68 ARM: legoev3: convert to driver model
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.

The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.

Signed-off-by: David Lechner <david@lechnology.com>
2019-07-13 11:11:28 -04:00
Michael Walle
fb9a1ffef3 rtc: add Microcrystal RV-8803 driver
Signed-off-by: Michael Walle <michael@walle.cc>
2019-07-13 11:11:28 -04:00
Derald D. Woods
9adaa039b6 usb: musb-new: omap2430: Fix compilation warning with USB_MUSB_GADGET
This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:

[...]
  CC      drivers/usb/gadget/f_mass_storage.o
  CC      drivers/usb/musb-new/omap2430.o
  CC      drivers/usb/gadget/f_fastboot.o
  CC      env/common.o
  CC      env/env.o
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
  ret = musb_register(&platdata->plat,
      ^
  LD      drivers/usb/host/built-in.o
  CC      drivers/usb/gadget/f_sdp.o
  CC      fs/ext4/ext4fs.o
[...]

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2019-07-13 11:11:27 -04:00
Derald D. Woods
e74e9f620a ARM: omap3: evm: Enable DM_USB in defconfig
This addresses the following warning message:

===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================

As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2019-07-13 11:11:27 -04:00
Derald D. Woods
5579e73c8c ARM: dts: omap3-evm: Sync dts(i) files from Linux 5.1.5
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2019-07-13 11:11:27 -04:00
Heiko Schocher
8dd6803ded rtc: ds1307: add support for m41t11
add m41t11 support in ds1307 driver. changes:

- add compatible string for m41t11
- check if RTC clock is running, if not
  enable the clock

Signed-off-by: Heiko Schocher <hs@denx.de>
2019-07-13 11:11:26 -04:00
Ezequiel Garcia
d66fb5b1f6 mmc: Register only the first MMC device on MMC_TINY
When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.

This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
2019-07-13 11:11:26 -04:00
Ezequiel Garcia
bf7c01d92b spl: Move SPL_MMC_TINY option to appear under SPL menu
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
2019-07-13 11:11:26 -04:00
Leo Ruan
8e92120b32 cmd: nvedit: Add sub-command 'env info'
Add sub-command 'env info' to display environment information:
- env_valid : is environment valid
- env_ready : is environment imported into hash table
- env_use_default : is default environment using

This command can be optionally used for evaluation in scripts:
[-d] : evaluate whether default environment is used
[-p] : evaluate whether environment can be persisted
The result of multiple evaluations will be combined with AND.

Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Do not enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-13 11:11:09 -04:00
Peng Fan
4213609cc7 drivers: core: use strcmp when find device by name
`if (!strncmp(dev->name, name, strlen(name)))` might find out
the wrong device, it might find out `dram_pll_ref_sel`, when name is
`dram_pll`. So use strcmp to avoid such issue.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-12 21:07:59 -04:00
Peng Fan
819ac50d2a test: dm: usb: use the real device name
"keyb" is not the real device name, "keyb@3" is.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-12 21:07:59 -04:00
Peng Fan
38ee9dfea9 test: dm: adc: use the real device name
"adc" is not the real device name, "adc@0" is.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-12 21:07:58 -04:00
Marek Behún
60ee60944b pci: ensure enumeration of all devices in pci_init
Use the uclass_first_device_check and uclass_next_device_check functions
instead of uclass_first_device and uclass_next_device in pci_init. This
ensures that all PCI devices are tried to be probed. Currently if a
device fails to probe, the enumeration stops and the devices which come
after the failed device are not probed.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-12 21:07:58 -04:00
Ilko Iliev
26eff45737 board: pm9263: Convert to CONFIG_DM_USB and CONFIG_DM_VIDEO
Convert the board to support the USB and video driver model and remove
the unnecessary code.
2019-07-12 10:04:29 -04:00
Ilko Iliev
7a0b1f713e board: pm9261: Convert to CONFIG_DM_USB and CONFIG_DM_VIDEO
Convert the board to support the USB and video driver model and remove
the unnecessary code.
2019-07-12 10:04:29 -04:00
Patrice Chotard
291f00bb3e board: st: add missing gpio_request() for stm32f429-discovery
This fixes the following error message:

U-Boot 2019.07-rc4-00103-g5eea874b5e (Jun 25 2019 - 15:09:31 +0200)

DRAM:  8 MiB
gpio@40021800: dir_output: error: gpio GPIOG14 not reserved
gpio@40021800: dir_output: error: gpio GPIOG13 not reserved
gpio@40021800: set_value: error: gpio GPIOG14 not reserved
Flash: 2 MiB
....

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-07-12 11:50:58 +02:00
Patrice Chotard
60bc487666 gpio: stm32: Remove .ofmatch callback
As compatible string "st,stm32-gpio" is no more used, .ofmatch
callback becomes useless, remove it.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:58 +02:00
Patrice Chotard
6084e96b99 ARM: dts: stm32: Remove useless "st, stm32-gpio" compatible string
Since pinctrl_stm32 driver update, each gpio bank is now binded
by pinctrl driver. The compatible string "st,stm32-gpio" becomes
useless, remove it.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:58 +02:00