imx31_litekit has been converted to the new relocation scheme, but it does not boot.
Make the boot functional by using board_early_init_f .
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
This fixes the MX31ADS build by using the new relocation scheme.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Felix Radensky <felix@embedded-sol.com>
The recent commit ea882baf9c broke embedding environments in the middle
of a sector, so relocate it to the start of the 2nd sector.
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Relocate the env to one of the small end sectors to avoid issues with
embedding it, such as support being broken (by recent commit ea882baf9c),
and for taking a while to save updates.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Minimal platform support to boot linux from SD.
Supported devices/hw limited to external MMC/SD slot,
GPIO, I2C and minimal PRCMU.
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>
We change default settings for egiga on mgcoge3un.
The reason we need this is that we have the gig port on mgcoge3un
connected using a back-to-back pair of PHYs. There are no magnetics and
because of that the port has to be run with a fixd configuration and
auto-negotiation must be disabled. In the default mode the egiga driver
uses autoneg to determine port speed - which defaults to 1G (we need
100M full duplex).
Add wait for the GPIO line connected to mgcoge3ne before
starting mgcoge3un. A board specific ethernet present function
was added, because on this board ethernet is always present.
The BOCO FPGA access was enhanced and changed to use register
definitions.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.
We add the BootROM init file for the mgcoge3un memphis RAM.
We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This is not supported on our km-arm boards since we have defined
CONFIG_SYS_NO_FLASH for our NAND Flash chip.
With CONFIG_CMD_JFFS2, the ls command is present and works very badly
on our km-arm boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
This environment variable is used to set the bootcount address
for the kernel.
last_stage_init is not available for arm platforms. So the
calls to set_km_var and set_bootcount_addr are done in
misc_init_r.
Additionally some unneeded printouts were removed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Since all the boards define the same env settings, this simplifies
the board files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This define is marvell specific, so it should be present in km_arm.
It is however not needed there either, since we set it to the default
value that is already set in include/asm/arch-kirkwood/config.h
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
commit ed59e58 (Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ) made the
definition of CONFIG_SYS_BOOTMAPSZ unnecessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
config.mk should not be used in board directory and should be removed.
Use the same approach for building the image as other MX51/MX53 boards.
After this change vision2 board can be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by: Jason Liu <jason.hui@linaro.org>
With the following commit, CONFIG_OF_LIBFDT is redefined.
2fa8ca98c3
Add CONFIG_OF_LIBFDT to more boards.
Remove the duplicated definition to fix CONFIG_OF_LIBFDT redefined
warning.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since the following commit, definition CONFIG_SYS_BOOTMAPSZ is not
needed any more.
ed59e58786
Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: add support for env in MMC/SPI on corenet ds boards
powerpc/85xx: Enable eSPI support on corenet ds boards
The pnvram size was used later from start scripts in linux. Therefore
it was added to the default environment.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
This is a first step to simplify the default environment. Move all
the environment variables which are only needed for debugging
purpose to textfiles in the scripts directory. In case of debugging
these files can be loaded via tftp into RAM and set via the env import
command. Other variables are identified as obsolete and were removed.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
BoardId and HWKey are used to identify the HW class of a given board.
The correct values are stored in the inventory eeprom. During creation
time of a boot package the boardId and HWkey for the SW is stored in
the default environment and burned into the flash. During boottime
the values in the inventory and in the environment are compared to
avoid starting of a SW which is not authorized for this board.
Some bootpackages are allowed to run on a set of different boardId
hwKey. In this case the environment variable boardIdListHex was added
to the default environment. In this case the command iterates over the
pair values and compares them with the values read from the inventory
eeprom.
The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The otc570 board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set. This patch implements the APM-proposed workaround.
To enable this patch for your board, add the appropriate define for your
CPU to your board header file. See kilauea.h for more information. The
following variants are supported:
#define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY
Please note that if you select the wrong define, your board will not
boot, and JTAG will be required to recover.
Tested on custom boards using:
CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com>
CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de>
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Though the OpenRD-Base only has one gigabit Ethernet port,
both the OpenRD-Client and OpenRD-Ultimate each have two.
On the Ultimate, the PHY addresses are consecutive, but
on the Client they are not.
(based on
<62a0952ce368acc725063a00a5ec680a639d6c27.1301040318.git.julian.pidancet@citrix.com>
<ad0a2dc1e422698b005d6f0ceb6dd6f75a87e00a.1301040318.git.julian.pidancet@citrix.com>
)
Signed-off-by: Clint Adams <clint@debian.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Julian Pidancet <julian.pidancet@citrix.com>
The asm/arch/config.h header define CONFIG_NR_DRAM_BANKS_MAX, which is
needed to configure DRAM banks.
This patch move the asm/arch/config.h header inclusion above the DRAM
banks configuration.
Additionally this patch fix a typo.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
The initial_boot_bank can be set when more than one application is
used in a bootpackage. But a value n <> 0 never led to booting from
bank n. Instead, bank 0 was booted. This patch fixes this.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
commit 91a3c14c (ppc, mgcoge: add DIP switch detection)
introduces an compile error due to an missing define in the
mgcoge2ne.h. DIP switch detection is valid for both boards.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Heiko Schocher <hs@denx.de>
On mgcoge3ne a new environment variable bobcatreset is used.
So this patch adds a possibility to add board specific
environment variables in general and this specific variable
for mgcoge3ne.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reserved bit was changed according to the processors manual.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Introduce a struct for the BFTICU FPGA to increase the readability of
the code. And the define CONFIG_SYS_BFTICU_BASE was removed because
the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
In order to support boardId / hwkey lists, the u-boot default
environment has been updated: Added a script checkboardidlist
which checks the list of boardId / hwkey if the boadrId / hwkey
of the IVM is included in that list. This feature is used if you
got different HW variants but you only want to create one boot
package. E.g. supx5 board series.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Add:
- introduce "bootrunner" environment variable
This allows to execute consecutive different commands
specified in the list "subbootcmd". If one command fails
the command serie will stop.
- introduce environment variable "develop", "ramfs" and "release"
Each variable is one way to boot our linux. "develop" is for
development purpose and boots the SW via NFS. "release" is for
booting the linux image from flash, "ramfs" allows to load an SW
image via tftp into ram and executes from there
- introduce "addmem" variable, this command adds the used memory
for linux to the bootargs
- introduce "addvar" variable, this command adress for the /var
directory to the kernel command line
- introduce "setramfspram" and "setrootfsaddr" these calculation
were done if "ramfs" was used (only for debugging)
- introduce "tftpramfs" used for "ramfs" to load the image into
RAM (only for debugging)
Remove unneeded stuff:
- CONFIG_IO_MUXING is obsolete for keymile boards
- CONFIG_KM_DEF_ENV_PRIVATE is also obsolete
- define CONFIG_SYS_TEXT_BASE in board configs only
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
This patch adds last_stage_init to all keymile boards. And
in the last stage init some environment variables for u-boot
were set. Currently these are pnvramaddr, pram and var address.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
define KM_IVM_BUS and KM_ENV_BUS macros
KM_IVM_BUS is used to define the EEprom_ivm environment variable.
These macros allow the reuse of these I2C addresses in other code
locations.
remove unneeded code
On first HW versions the BOCO FPGA was behind a MUX device. These
HW versions are not supported anymore. And therefore this code can
be removed.
added LED initialization for SUEN3
The bootstat LED required to be initialized so to have a green
colour after start-up.
define CONFIG_SYS_TEXT_BASE
This is needed by the relocation code and is not the same for
our ARM BEC and thus needs to be defined.
remove memsize variable
An environment variable for memsize is not needed.
this can be get via the board info struct.
remove unneeded double access to bi_dram[i].size field
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Luca Haab <luca.haab@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
For the kmsupx5 a new header file was introduced km8321-common.h.
Now the common stuff from tuxa1, tuda1 and suvd3 was removed and
the new header file included.
The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are
confusing. Because they actually describe the KMBEC FPGA values.
The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore
all the defines were renamed.
remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is
already declared in keymile-common.h
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch renames the suen3 defines and functions to KM_KIRKWOOD
which is more generic and more precise, because these values
and functions where used by all suenX boards and not only suen3.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.
Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
First step for a cleanup of all header files for km8321 boards.
Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch reworks all headerfiles for keymile boards. Furthermore
the environment variables are refactored.
Changes:
- introduce km-powerpc.h file and extract ppc specific parts to it
- move ARM specific options and vaiables to km_arm.h
- sort the environment variables to logical groups
- enhance the description of the environment variables
- remove KM specific HW key and board id from kernel command line
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- adapt copyright string
- change bootdelay to 2 seconds
- set max number of command args to 32
- set I/O buffer size to 512
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- use I/O accessors
-> For accessing the FPGA therefore a struct km_bec_fpga
is introduced.
- no longer externs needed
- to defines, that only select functions, don;t assign a
numeric value
- Codingstyle changes to prevent checkpatch errors/warnings
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The MACH_TYPE SUEN3 is now to specific for keymile boards, because
other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed
to MACH_KM_KIRKWOOD.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
CONFIG_SYS_BOOTMAPSZ has been 64M on these boards for some time so we
should also allow the kernel image to be up to 64M decompressed. This
also matches what we pass to the OS based on the ePAPR specification.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also added support to save env to spi flash in case of SPIBOOT.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove an empty board_early_init_f() from the MPC8641HPCN board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The following boards gain device tree support with this patch:
ca9x4_ct_vxp - Versatile Express
i.mx5 boards:
efikamx
mx51evk
mx53evk
OMAP boards:
devkit8000
igep0020
igep0030
omap3_overo
omap3_pandora
omap4_sdp3430
omap3_zoom1
omap3_zoom2
omap4_panda
omap4_sdp4430
Tegra boards:
Harmony
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes a wrong address define in corenet_ds.h (used by
P4080DS.h, P3041DS.h, P5020DS.h).
Since board/Freescale/corenet_ds/tlb.c does not use the
CONFIG_SYS_PCIE3_MEM_VIRT define (uses CONFIG_SYS_PCIE1_MEM_VIRT with a
fix offset instead) this has no effect to the functionality. But it may
be important for changes in the future?
Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we boot from a SD card use it for the environment as well.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot environments, esp. when boards are shared across multiple
users, can get pretty large and time consuming to visually parse.
The grepenv command this patch adds can be used in lieu of printenv
to facilitate searching. grepenv works like printenv but limits
its output only to environment strings (variable name and value
pairs) that match the user specified substring.
the following examples are on a board with a 5313 byte environment
that spans multiple screen pages:
Example 1: summarize ethernet configuration:
=> grepenv eth TSEC
etact=FM1@DTSEC2
eth=FM1@DTSEC4
ethact=FM1@DTSEC2
eth1addr=00:E0:0C:00:8b:01
eth2addr=00:E0:0C:00:8b:02
eth3addr=00:E0:0C:00:8b:03
eth4addr=00:E0:0C:00:8b:04
eth5addr=00:E0:0C:00:8b:05
eth6addr=00:E0:0C:00:8b:06
eth7addr=00:E0:0C:00:8b:07
eth8addr=00:E0:0C:00:8b:08
eth9addr=00:E0:0C:00:8b:09
ethaddr=00:E0:0C:00:8b:00
netdev=eth0
uprcw=setenv ethact $eth;setenv filename p4080ds/R_PPSXX_0xe/rcw_0xe_2sgmii_rev2_high.bin;setenv start 0xe8000000;protect off all;run upimage;protect on all
upuboot=setenv ethact $eth;setenv filename u-boot.bin;setenv start eff80000;protect off all;run upimage;protect on all
upucode=setenv ethact $eth;setenv filename fsl_fman_ucode_P4080_101_6.bin;setenv start 0xef000000;protect off all;run upimage;protect on all
usdboot=setenv ethact $eth;tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/initramfs.cpio.gz.uboot;tftp c00000 $dir/p4080ds-usdpaa.dtb;setenv bootargs root=/dev/ram rw console=ttyS0,115200 $othbootargs;bootm 1000000 2000000 c00000;
=>
Example 2: detect unused env vars:
=> grepenv etact
etact=FM1@DTSEC2
=>
Example 3: reveal hardcoded variables; e.g., for fdtaddr:
=> grepenv fdtaddr
fdtaddr=c00000
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
=> grep $fdtaddr
fdtaddr=c00000
my_boot=bootm 0x40000000 0x41000000 0x00c00000
my_dtb=tftp 0x00c00000 $prefix/p4080ds.dtb
nohvboot=tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/$ramdiskfile;tftp c00000 $dir/$fdtfile;setenv bootargs root=/dev/ram rw ramdisk_size=0x10000000 console=ttyS0,115200;bootm 1000000 2000000 c00000;
=>
This patch also enables the grepenv command by default on
corenet_ds based boards (and repositions the DHCP command
entry to keep the list sorted).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
This patch defines all the needed symbols in the header file
and removes the now-unused config.mk in board directory.
Changes to board C file as requested.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
- fix board support following relocation changes
- switch to boards.cfg
- disable i2c to keep size under 128kiB (1 sector)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Move the header file and definitions of ftsmc020
static memory control unit from a320 SoC folder to
"drivers/mtd" folder.
This change will let other SoC which also use ftsmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
- update to new relocation code
- switch to boards.cfg
- get rid of LEGACY (still a little hack in .h to compile)
- add nand boot configuration
- boot tested for the following configurations :
9260 (64MB RAM & nor boot)
9260_nand (64MB RAM & nand boot)
9G20_128M (128MB RAM & nor boot)
9G20_nand_128M (128MB RAM & nand boot)
(nor boot is using lowlevel init)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.
The board support is based on the BeagleBoard implementation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Removed boot_flash_* extern variables.
boot_flash_type was totally unused. The other ones were actually constants, so
they have been replaced with #defines in the board config files.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The reset sequence/configuration for ehci is highly board specific,
so this will be done in the source for the board, instead of
introducing several CONFIG_* which would be needed to make those
few lines in beagle.c usable across different OMAP boards.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The default IGEP configuration doesn't do anything useful; using some
boot.scr search logic like BeagleBoard is much more useful.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
configuration
The default IGEP configuration doesn't do anything useful; using some
boot.scr search logic like BeagleBoard is much more useful.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
For better sharing with other platform other than pxa's,
it is more convenient to put the driver to the common place.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
ftpmu010 related code has been moved to drivers/power/.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
CM-T3730 is exactly the same board as CM-T35, but it has
TI DM3730 SoC onboard and therefore some changes have to take place
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Use CONFIG_OMAP3_MMC in cm-t35 configuration file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Patch was updated by Jason Kridner <jkridner@beagleboard.org>:
* Use tabs to match style of other board revisions
* Only include board revisions that exist
* Default to the same configuration as the latest revision, but
without setting 'beaglerev'
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Using the new env import command it is possible to use plain text files instead
of script-images. Plain text files are much easier to handle.
E.g. If your boot.scr contains the following:
-----------------------------------
setenv dvimode 1024x768-16@60
run loaduimage
run mmcboot
-----------------------------------
you could create a file named uEnv.txt and use that instead of boot.scr:
-----------------------------------
dvimode=1024x768-16@60
uenvcmd=run loaduimage; run mmcboot
-----------------------------------
The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt
was loaded. If uenvcmd doesn't exist the default boot sequence will be started,
therefore you could just use
-----------------------------------
dvimode=1024x768-16@60
-----------------------------------
as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added LED driver using status_led. USR0 is set to monitor the boot
status. USR1 is set to be the green LED.
Included adding configuration and command to the default configuration.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
device tree for uboot arm support has already been enabled
in the master branch. This patch enable device tree support
for mx51/53 evk board for DT test.
Signed-off-by: Jason Liu <r64343@freescale.com>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
The previous patch makes u-boot use the full accessible size of ram as
the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined,
which means boot_relocate_fdt() can be changed to depend solely on
CONFIG_OF_LIBFDT.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be
stopped with well defined keypresses.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CONFIG_ENV_SIZE = CONFIG_ENV_SECT_SIZE = 128kB but CONFIG_SYS_STACK_SIZE
is only 32kB resulting in saveenv causing a stack overflow and crashing
U-Boot. Resolve by reducing CONFIG_ENV_SIZE to 4kB
Also fix up CONFIG_SYS_MALLOC_LEN to correctly use environment sector
size and add some comments to the memory organisation configuration
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR
and allow that the architecture-specific default value gets
overwritten by defining the value in the board header file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
