Commit Graph

8045 Commits

Author SHA1 Message Date
Benoît Thébaudeau
959eaa74b8 arm: relocate_code() is no longer noreturn
Commit e05e5de7fa made ARM's relocate_code()
return to its caller, but it did not update its declaration accordingly.

Fixing this function declaration fixes dropped C code following calls to
relocate_code().

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:05 +02:00
Benoît Thébaudeau
68fbc0e686 imx: mx53ard: Add support for NAND Flash
Add support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB
pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard.

eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this
board, which satisfies the 30-ns NF R/W cycle requirement.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-12 07:55:04 +02:00
Benoît Thébaudeau
35537bc773 nand: mxc: Add support for i.MX5
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-12 07:55:04 +02:00
Benoît Thébaudeau
2dc0aa0227 nand: mxc: Prepare to add support for i.MX5
Add some abstraction to NFC definitions so that some parts of the current code
can also be used for future i.MX5 code.

Clean up a few things by the way.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-12 07:55:04 +02:00
Tom Rini
dd2445ec1b omap5_common.h: Use fallback CONFIG_SYS_BAUDRATE_TABLE
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-08 11:40:59 -04:00
Tom Rini
9552ee3ea9 omap5_uevm.h: Move uEVM-specific choices to omap5_uevm.h
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there.  Other platforms may not, so
move this choice to the EVM config.  In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.

Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-08 11:40:56 -04:00
SRICHARAN R
aaed0a23c9 ARM: OMAP4/5: Make bootz as the default boot command
So with OMAP added to multi platform kernel,
the uImage no more contains a valid load address.
With the uboot already supporting zImage,
change the default boot command to bootz
instead.

Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
2013-04-08 11:29:05 -04:00
SRICHARAN R
143070df8e ARM: OMAP4/5: Change the default boot command to work with device tree
Now with kernel moving to all device tree, the default
boot command is changed to pass the device tree blob.
Also, adding the findfdt command to get the dt-blob
based on the board.

Thanks to Tom Rini <trini@ti.com> for suggesting this.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-04-08 11:29:05 -04:00
Nishanth Menon
78fd004107 omap5: Allow use of a plain text env file
For production systems it is better to use script images since
they are protected by checksums and carry valuable information
like name and timestamp. Also, you can't validate the content
passed to env import.

But for development, it is easier to use the env import command and
plain text files instead of script-images.

Since both OMAP5evm/uevm boards are used primarily for development,
we allow U-Boot to load env var from a text file in case that an
boot.scr script-image is not present.

The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.

Inspired by commit: d70f54808d
(omap4: allow the use of a plain text env file instead boot scripts)

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sricharan R <r.sricharan@ti.com>
2013-04-08 11:29:05 -04:00
SRICHARAN R
d3501ed584 ARM: OMAP5: Set fdt_high to enable booting with Device tree
While booting with dt blob, if fdt_high is not set to
0xffffffff, the dt blob gets relocated to a high ram address,
which the kernel is not able to use without HIGHMEM.

So set it to 0xffffffff to avoid the issue.

Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
2013-04-08 11:29:05 -04:00
SRICHARAN R
2c2a9f3a1f ARM: OMAP5: Rename omap5_evm to omap5_uevm
The omap5-uevm is the reference board name for OMAP5 soc
based platform. So rename it accordingly.

Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
2013-04-08 11:29:05 -04:00
Hunter, Jon
d1da76e9f8 omap2420-h4: Fix get_timer() and CONFIG_SYS_HZ
The function get_timer() should return time in ms and CONFIG_SYS_HZ
should be set to 1000 by default. Fix both of these items.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-08 11:29:05 -04:00
Hunter, Jon
faad9c0256 omap2420-h4: Add device tree support
Enable device-tree support for the omap2420-h4 board.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-08 11:29:05 -04:00
Hunter, Jon
47f58a7357 omap2420-h4: Fix booting from NOR flash
The omap2420-h4 board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash. Please note
that OMAP maps the NOR flash to address 0x08000000 by default and so
use this as the default address for the NOR flash.

Also remove legacy code that attempts to calculate where in flash the
sdata structure, that holds the memory interface configuration data,
is located. By changing the default linker location for code to flash
this is no longer necessary.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-08 11:29:05 -04:00
Andreas Bießmann
616cf60ee0 tricorder: enable hw assisted BCH8 in SPL and u-boot
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Scott Wood <scottwood@freescale.com>
2013-04-08 11:29:05 -04:00
Manfred Huber
fd2aeac560 omap3_beagle: Flush UART3 xmit on enable if TEMT is broken
Flush UART3 xmit on enable if TEMT is broken

On some OMAP3 devices when UART3 is configured for boot mode before SPL starts
only THRE bit is set. We have to empty the transmitter before initialization
starts. This patch avoids the use of CONFIG_SYS_NS16550_BROKEN_TEMT.

Signed-off-by: Manfred Huber <man.huber@arcor.de>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-04-08 11:29:05 -04:00
Bin Liu
4de602f2b0 musb: am335x: disable bulk split-combine feature
On TI AM335x devices, MUSB has bulk split/combine feature enabled
in the ConfigData register, but the current MUSB driver does not
support it yet. Therefore, disable the feature for now, until the
driver adds the support.

One usecase which is broken because of this feature is that Ether
gadget stops working in Fullspeed mode (by un-defining
CONFIG_USB_GADGET_DUALSPEED)

After desabled this feature, MUSB driver send packets in proper size
(no more than 64 bytes) in Fullspeed mode.

This has been validated with Ether gadget in Fullspeed mode on AM335x
EVM.

Signed-off-by: Bin Liu <b-liu@ti.com>
2013-04-08 11:29:04 -04:00
Albert ARIBAUD
fed029f3c3 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-04-04 15:44:57 +02:00
Albert ARIBAUD
be08abc242 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-04-04 11:49:32 +02:00
Stephen Warren
5eaa215607 ARM: bcm2835: fix get_timer() to return ms
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.

Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2013-04-04 08:14:54 +02:00
Fabio Estevam
d8e9eb9c04 wandboard: Remove CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_USDHC_NUM is not used for wandboard.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03 11:40:44 +02:00
Fabio Estevam
773d56d40d mx6qsabrelite: Remove duplicate 'mmc dev'
No need to call 'mmc dev' twice.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03 11:40:44 +02:00
Fabio Estevam
69089245c2 wandboard: Remove duplicate 'mmc dev'
No need to call 'mmc dev' twice.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03 11:40:44 +02:00
Alexandre Pereira da Silva
50cea244fe mx23_olinuxino: Fix netboot console
The netargs variable was referencing the non-existing variable
console_mainline. Change that to console variable instead.

Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03 11:28:40 +02:00
Abbas Raza
aad4659a2f mmc: i.MX6: fsl_esdhc: Define maximum bus width supported by a board
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.

It is tested with a MMCplus card.

Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2013-04-03 11:26:28 +02:00
Otavio Salvador
2feae93ac0 mx23_olinuxino: Change definitions to use spaces instead of tabs
Change all "#define/ifdef<TAB>" sequences into "#define/ifdef<SPACE>".

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03 11:26:12 +02:00
Benoît Thébaudeau
d37b33481d mx25pdk: Enable imxdi RTC
The mx25pdk board supports the i.MX25 DryIce RTC (imxdi), so enable it. This
allows to compile-test the imxdi driver in the mainline tree.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-03 11:26:12 +02:00
Fabio Estevam
ab461be65d mx28evk: Introduce a new target for saving env vars to NAND
Introduce 'mx28evk_nand' target for saving environment variables into NAND.

The mx28evk board does not come with a NAND flash populated from the
factory. It comes with an empty slot (U23), which allows the insertion of a
48-pin TSOP flash device.

Tested with a K9LBG08U0D.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03 10:55:18 +02:00
Otavio Salvador
85449dbd4b mx6qsabre{sd,auto}: Add boot mode select
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03 10:41:51 +02:00
Akshay Saraswat
4f3bfa97c4 Exynos5: config: enable time command
This patch enables time command.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-04-01 14:02:07 +09:00
Akshay Saraswat
2c6346c1be Exynos: config: Enable hash command
This enables hash command.

Tested with command "hash sha256 0x40008000 0x2B 0x40009000".
Used mm and md to write a standard string to memory location
0x40008000 and ran the above command to verify the output.

Signed-off-by: ARUN MANKUZHI <arun.m@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-03-29 20:10:42 +09:00
Akshay Saraswat
1f9c92808a gen: Add sha h/w acceleration to hash
Adding H/W acceleration support to hash which can be used
to test SHA 256 hash algorithm.

Signed-off-by: ARUN MANKUZHI <arun.m@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-03-29 20:10:42 +09:00
Akshay Saraswat
8e6ee2933c Exynos: config: Enable ACE HW for SHA 256 for Exynos
This enables SHA 256 for exynos.

Signed-off-by: ARUN MANKUZHI <arun.m@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-03-29 20:10:42 +09:00
Przemyslaw Marczak
dc993a65f4 spl:falcon:trats: Fix SPL image size computing.
"spl_imgsize" was set as decimal variable by "setexpr"
and this causes wrong image size written by "ext4write".
Preset this val with "0x" prefix allow to fix this issue.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-29 11:42:35 +09:00
Albert ARIBAUD
009d75ccc1 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	drivers/spi/tegra20_sflash.c
	include/fdtdec.h
	lib/fdtdec.c
2013-03-28 18:50:01 +01:00
Steven Stallion
04d414090c image: Add support for Plan 9
Signed-off-by: Steven Stallion <sstallion@gmail.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-27 15:30:11 -04:00
Tom Rini
268d966dff env_callback: Mark find_env_callback as static
This is not called outside of env_callback.c so mark static, remove from
<env_callback.h>

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2013-03-27 15:30:11 -04:00
Ajay Kumar
1e4706a715 EXYNOS5: FDT: Add compatible strings for FIMD
Add required compatible information for FIMD.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-27 21:23:11 +09:00
Ajay Kumar
d7377b5193 EXYNOS: FDT: Add compatible strings for FIMD
Add required compatible information for FIMD.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-27 21:17:23 +09:00
Ajay Kumar
29fd57046e video: exynos_fb: Remove callbacks from the driver
Replaced the functionality of callbacks by using a standard set of functions.
Instead of implementing and hooking up a callback, put the same code in one of
the standard set of functions by overriding it.

This patch is tested only on SMDK5250.
For Trats and universal_c210 board, it is only compile tested.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-27 21:17:12 +09:00
Albert ARIBAUD
ebd749da69 Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2013-03-26 10:40:13 +01:00
Albert ARIBAUD
412665b461 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-03-26 09:51:09 +01:00
Tom Warren
f789be6086 Tegra114: MMC: Enable DT MMC driver support for Tegra114 Dalmore boards
Tested on my Dalmore E1611 board, eMMC and SD-Card work fine, can load
a kernel off of an SD card OK, card detect works, and the env is now
stored in eMMC (end of the 2nd 'boot' sector, same as Tegra20/30).

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:08 -07:00
Allen Martin
ec37b2b423 tegra114: dalmore: config: enable SPI
Turn on SPI in dalmore config file

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:07 -07:00
Allen Martin
77c42e80b9 tegra114: add SPI driver
Add driver for tegra114 SPI controller.  This controller is not
compatible with either the tegra20 or tegra30 controllers, so it
requires a new driver.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:07 -07:00
Allen Martin
c3bb3c8bb3 tegra114: fdt: add compatible string for tegra114 SPI ctrl
Add "nvidia,tegra114-spi" to represent t114 SPI controller hardware.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:06 -07:00
Allen Martin
78f47b7353 spi: add common fdt SPI driver interface
Add a common interface to fdt based SPI drivers.  Each driver is
represented by a table entry in fdt_spi_drivers[].  If there are
multiple SPI drivers in the table, the first driver to return success
from spi_init() will be registered as the SPI driver.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:06 -07:00
Allen Martin
ff1da6fb5f tegra: spi: rename tegra SPI drivers
Rename tegra SPI drivers to tegra20_flash and tegra20_slink in
preparation for commonization and addition of tegra114_spi.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-25 09:56:05 -07:00
Albert ARIBAUD
b6379e15a7 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-03-24 17:52:22 +01:00
Matt Porter
ea7b96b6aa ti814x_evm: add ti814x evm board support
Add TI814X EVM board directory, config file, and MAINTAINERS
entry. Enable build.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt to recent omap_hsmmc requirements, Matt re-tested]
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:12 -04:00