Commit Graph

17 Commits

Author SHA1 Message Date
Masahiro Yamada
93d4334f7f Add board MAINTAINERS files
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.

The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.

After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.

TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:06 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
pekon gupta
68128e0a86 omap3: remove remnant macros GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:07 -04:00
Stefan Roese
3e51b7c8b8 arm: omap3: Add SPL support to cm_t35
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.

Tested by booting via MMC and NAND.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-12-12 14:54:22 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Nikita Kiryanov
63c4f17b2f cm_t35: use scf0403 driver
Use scf0403 driver to add scf0403x LCD support for cm-t35 and cm-t3730
boards.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-11-12 10:12:07 +01:00
Igor Grinberg
ebc18afd0a cm-t35: use gpio_led driver for status led
Switch to using the generic gpio_led driver instead of the private to
cm_t35 board led implementation.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-11 12:17:06 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Igor Grinberg
e1e55c13c9 cm-t35: move the display code to common place
Compulab OMAP3 boards use the same display initialization code.
Move the display initialization code to live under board/compulab/common
directory.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-01 15:55:59 -04:00
Igor Grinberg
689be5f83c cm-t35: move the eeprom code to common place
Compulab boards use the same eeprom code, so move the eeprom related
code to live under board/compulab/common directory.
Also make several adjustments to eeprom functions namespace, so it will
be generic for compulab boards.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-01 15:55:59 -04:00
Masahiro Yamada
a79854a90f board: arm: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@ti.com>
2013-11-01 11:42:12 -04:00
Troy Kisky
127efc4fe8 usb: ehci-hcd: add enum usb_init_type parameter to ehci_hcd_init.
This paramter will later be used to initialize OTG ports in
host or device mode.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:46:27 +02:00
Mateusz Zalega
16297cfb2a usb: new board-specific USB init interface
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.

New API allows selective initialization of USB controllers whenever needed.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
2013-10-20 23:42:40 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Robert Winkler
327598945b omap: cm_t35: Fix cm_t35 for weak splash_screen_prepare
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-07-01 21:47:40 +02:00
Igor Grinberg
811acf923d cm-t35: move cm-t35 to live in compulab directory
Currently the cm-t35 support code lives under board/cm_t35 directory.
Some of the code can be shared with other/future CompuLab boards,
so move the cm-t35 to live under board/compulab/cm_t35 directory.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-05-10 08:25:56 -04:00