Merge mxc_setup_config1() into board_nand_init() in order to ease the addition
of i.MX5 support in the following patches.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
mxc_nand_read_page_raw_syndrome() should reenable ECC upon exit. This fixes ECC
errors left uncorrected after a call to this function.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use _mxc_nand_enable_hwecc() instead of duplicating its code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the NFC IP 1.1, the 32-bit ecc_status_result value comes from 2
consecutive 16-bit registers. This patch reads all the fields of this value,
which makes a difference for 4-kiB NF pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patches fixes the TODO to use same register definitions in mtd mxc_nand and
nand_spl fsl nfc drivers.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When writing 0x4000 to the unlockend_blkaddr register, large writes to
a 2k page NAND sometimes fail. The current kernel driver writes 0xFFFF
to this register for V2 of the nand controller.
However on an i.MX31 this also fixes writes larger than 32MB.
The datasheet is very unspecific, but (0x4000=16384)*2000
roughly fits the limits we're encountering with NAND writes.
This problem might be NAND chip specific.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for version 1.1 of the nfc nand flash
controller which is on the i.mx25 soc.
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Scott Wood <scottwood@freescale.com>
Import the large page oob layout from Linux mxc_nand.c driver.
The CONFIG_SYS_NAND_LARGEPAGE option is used to activate
the large page oob layout. Run time detection is not supported
as this moment.
This has been tested on the i.MX31 PDK board with a large
page NAND device.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Driver for NFC NAND controller found on Freescale's MX2 and MX3
processors. Ported from Linux. Tested only with i.MX27 but should
works with other MX2 and MX3 processors too.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
