Commit Graph

601 Commits

Author SHA1 Message Date
Alan Ott
cab8a27d80 i2c: at91_i2c: remove the .probe_chip function
The .probe_chip function is supposed to probe an i2c device on the bus to
determine whether a device is answering to a particular address.
at91_i2c_probe_chip() did not do anything resembling this and always
returned 0.

It looks as though at91_i2c_probe_chip() was intended to be a .probe
function for the controller, as it was copied-and-pasted to become
at91_i2c_probe() in 0bc8f640a4.

Removing the at91_i2c_probe_chip() function makes the higher layer
(i2c_probe_chip()) try a zero-length read transfer to test for the
presence of a device instead, which does work.

Signed-off-by: Alan Ott <alan@softiron.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-12-07 09:29:19 +01:00
Alan Ott
0afbb0e1c0 i2c: at91_i2c: Wait for TXRDY after sending the first byte
The driver must wait for TXRDY after each byte is pushed into
the i2c FIFO before pushing the next byte. Previously this was
not done for the first byte, causing a race condition with zeros
sometimes being sent for the next byte (which is typically the
first actual data byte).

Signed-off-by: Alan Ott <alan@softiron.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-12-07 09:28:58 +01:00
Beniamino Galvani
50a69095cb i2c: meson: add some comments
Add some comment describing the purpose of struct members and
functions.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-12-07 09:28:42 +01:00
Beniamino Galvani
989bb924c4 i2c: meson: fix return codes on error
Change meson_i2c_xfer_msg() to return -EREMOTEIO in case of NACK, as
done by other drivers. Also, don't change the return error in
meson_i2c_xfer().

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-12-07 09:28:31 +01:00
Beniamino Galvani
8c47ab6b3b i2c: meson: reduce timeout
The datasheet doesn't specify a suggested timeout and 500ms seems very
long: reduce it to 100ms.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-12-07 09:28:21 +01:00
Beniamino Galvani
4ecbb8b678 i2c: meson: improve Kconfig description
Expand the Kconfig description with hardware features.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-12-07 09:28:06 +01:00
Marek Vasut
9e75ea46d5 i2c: rcar_iic: Add RCar IIC driver
Add driver for the RCar IIC or DVFS I2C controller. This driver is based
on the SH I2C driver, but supports DM and DT probing as well as modern
I2C framework API.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:32:34 +01:00
Tom Rini
6e6cf015e7 Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 07:22:11 -05:00
Beniamino Galvani
f8d9ca1833 i2c: add Amlogic Meson driver
Add a driver for the I2C controller available on Amlogic Meson SoCs.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-20 10:11:34 +01:00
Nandor Han
2feec4eafd imx: mxc_i2c: tweak the i2c transfer method
Tweak the i2c transfer to work for devices that want to read data
without addressing a register.

Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Masahiro Yamada
af6715bfb4 i2c: fti2c010: remove unused/unmaintained driver
CONFIG_SYS_I2C_FTI2C010 is not enabled by anyone.

Commit 2852709676 ("dm: i2c: Add a note to I2C drivers which need
conversion") prompted to convert this driver to DM before June 2017,
but not converted yet.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
2017-10-27 08:52:22 -04:00
Masahiro Yamada
1d14cbdcd8 i2c: adi_i2c: remove left-over Blackfin I2C driver
This driver was used by Blackfin boards, but Blackfin support is
gone.  There is no user of this driver.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
2017-10-27 08:52:22 -04:00
Patrice Chotard
d10bd6cfd8 i2c: stm32f7_i2c: fix usage of useless local variable
Remove useless local variable "s" and use directly
function's parameter "output"

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-10-17 11:28:41 +02:00
Christophe Kerello
81c4843763 i2c: stm32f7_i2c: fix data abort
As "v" is a local variable in stm32_i2c_choose_solution()
"v" has to be copied into "s" to avoid data abort in
stm32_i2c_compute_timing().

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-10-17 11:28:27 +02:00
Masahiro Yamada
c4e5990ad2 i2c: remove DECLARE_GLOBAL_DATA_PTR from i2c-uclass
No global pointer is used in this file.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-10-17 11:27:42 +02:00
Masahiro Yamada
2b7b2df91e i2c: uniphier-f: replace debug() with dev_dbg()
Use dev_dbg() functions.  It will be helpful to prefix log messages
with the corresponding device name when the core framework is ready.

While I am here, I renamed "dev", which was actually private data,
into "priv" because dev->dev looks confusing.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:25 +09:00
Masahiro Yamada
804cf1c46f i2c: uniphier: replace debug() with dev_dbg()
Use dev_dbg() functions.  It will be helpful to prefix log messages
with the corresponding device name when the core framework is ready.

While I am here, I renamed "dev", which was actually private data,
into "priv" because dev->dev looks confusing.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:24 +09:00
Chris Packham
5bc90a8953 i2c: muxes: pca954x: look up width from chip_desc
Commit 8e6eda7cda ("drivers/i2c/muxes/pca954x: Add pca9547 I2C mux
support") introduced a chip_desc for the pca954x devices but failed to
update pca954x_ofdata_to_platdata() to be aware of it. Make
pca954x_ofdata_to_platdata() lookup the chip_desc to validate the device
width.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
2017-10-11 06:17:22 +02:00
Simon Glass
7c84319af9 dm: gpio: Correct use of -ENODEV in drivers
In U-Boot -ENODEV means that there is no device. When there is a problem
with the device, drivers should return an error like -ENXIO or -EREMOTEIO.
When the device tree properties cannot be read correct , they should
return -EINVAL.

Update various GPIO drivers to follow this rule, to help with consistency
for future driver writers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Adam Ford <aford173@gmail.com>
2017-10-08 20:41:09 -06:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00
Elaine Zhang
be93fc2476 rockchip: i2c: rk3328: support i2c for rk3328 SoC
Add compatible to support rk3328 i2c

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Heiko Schocher<hs@denx.de>
2017-10-01 00:33:33 +02:00
Philipp Tomsich
cc91bdf8d4 rockchip: i2c: Convert to livetree
Update the Rockchip I2C driver to support livetree.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Heiko Schocher <hs@denx.de>
2017-09-18 20:40:35 +02:00
Moritz Fischer
36bdeb75a4 i2c: muxes: pca954x: Add support for GPIO reset line
This commit adds support for GPIO reset lines matching the
common linux "reset-gpios" devicetree binding.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-13 05:35:48 +02:00
Wadim Egorov
5deaa53028 rockchip: i2c: fix >32 byte reads
The hw can read up to 32 bytes at a time. If we need
more than one chunk, we have to enter the plain RX mode.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-05 11:13:36 +02:00
Adam Ford
fc760cc6e8 Convert CONFIG_SYS_I2C_BUS_MAX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix AM43XX drop AM44XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 20:44:30 -04:00
Adam Ford
ac1d8ac871 Configs: Migrate I2C_BUS_MAX to CONFIG_SYS_I2C_BUS_MAX
For consistency with other platforms and in preparation of Kconfig
migration, let's change Several TI platforms that use I2C_BUS_MAX
to CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-01 17:56:20 -04:00
Peng Fan
a430556ecb i2c: muxes: add i2c gpio multiplexer driver
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.

E.G. something like:

         ----------              ----------  Bus segment 1   - - - - -
        |          | SCL/SDA    |          |-------------- |           |
        |          |------------|          |
        |          |            |          | Bus segment 2 |           |
        |  Linux   | GPIO 1..N  |   MUX    |---------------   Devices
        |          |------------|          |               |           |
        |          |            |          | Bus segment M
        |          |            |          |---------------|           |
         ----------              ----------                  - - - - -

SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.

Note commit log from kernel
commit 92ed1a76("i2c: Add generic I2C multiplexer using GPIO API")

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com> (i.MX6QP-Sabreauto)
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2017-08-23 07:04:56 +02:00
Patrice Chotard
4fadcaf097 i2c: add i2c driver for stm32
Add i2c driver which can be used on both STM32F7 and STM32H7.
This I2C block supports the following features:
 _ Slave and master modes
 _ Multimaster capability
 _ Standard-mode (up to 100 kHz)
 _ Fast-mode (up to 400 kHz)
 _ Fast-mode Plus (up to 1 MHz)
 _ 7-bit and 10-bit addressing mode
 _ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask)
 _ All 7-bit addresses acknowledge mode
 _ General call
 _ Programmable setup and hold times
 _ Easy to use event management
 _ Optional clock stretching
 _ Software reset

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-23 07:04:40 +02:00
Marek Vasut
014e47f028 i2c: designware: Allow sending restart conditions
Allow sending restart conditions upon direction change as this is
required by some chips.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denxx.de>
2017-08-10 12:02:50 +02:00
Adam Ford
daa0f0500f Convert CONFIG_SYS_I2C_OMAP24XX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_OMAP24XX

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-08-10 12:02:32 +02:00
Adam Ford
94d50bed65 Configs: Migrate CONFIG_SYS_I2C_OMAP34XX to CONFIG_SYS_I2C_OMAP24XX
The driver is for all boards 24XX and up, so let's eliminate the
extra option called CONFIG_SYS_I2C_OMAP34XX since the driver checks
for CONFIG_OMAP34XX we don't need CONFIG_SYS_I2C_OMAP34XX.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-08-09 06:14:13 +02:00
Wenyou.Yang@microchip.com
0bc8f640a4 i2c: at91: Add missing probe function to device driver
Add missing probe function to the device driver to active a device.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-08-09 06:13:53 +02:00
Simon Glass
d8554d0853 dm: tegra: i2c: Convert to livetree
Update the tegra i2c driver to support a live device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
2017-07-28 12:02:47 -06:00
Christophe Leroy
72281c5c46 powerpc: Remove 8260 remainders
commit 2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260")
removed support for 8260 CPU.

This patch remove some remainders.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-23 09:24:47 -04:00
Tom Rini
39632b4a01 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-07-18 08:42:48 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Marek Behún
8e6eda7cda drivers/i2c/muxes/pca954x: Add pca9547 I2C mux support
This I2C mux is found, for example, on the Turris Omnia board.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-07-12 06:56:48 +02:00
Christophe Leroy
b1e41d1cee powerpc, 8xx: Migrate to Kconfig
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-07-08 15:56:01 -04:00
Andy Shevchenko
daab59ac05 avr32: Retire AVR32 for good
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).

Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).

There is no good point to keep this support in U-Boot either.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2017-07-06 16:17:19 -04:00
Heiko Schocher
98f705c9ce powerpc: remove 4xx support
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-07-03 17:35:28 -04:00
Heiko Schocher
2eb48ff7a2 powerpc, 8260: remove support for mpc8260
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-12 08:38:02 -04:00
Heiko Schocher
5b8e76c35e powerpc, 8xx: remove support for 8xx
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-12 08:37:55 -04:00
Simon Glass
5a8ba315f1 samsung: Drop more references fo s3c24x0
This is dead code now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-05 11:02:31 -04:00
Simon Glass
aabf79929e dm: sandbox: i2c: Drop fdtdec.h header
This is not needed in this driver. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:16 -06:00
Simon Glass
1704308eb6 dm: i2c: Convert uclass to livetree
Update the i2c uclass to support a live device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:12 -06:00
Simon Glass
150c5afe5b dm: gpio: Add live tree support
Add support for requesting GPIOs with a live device tree.

This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-01 07:03:10 -06:00
Simon Glass
45a26867e8 dm: core: Update device_bind_driver_to_node() to use ofnode
Adjust this function to us an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:08 -06:00
Simon Glass
a821c4af79 dm: Rename dev_addr..() functions
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

   1. dev_read_addr...()    - works on devices, supports flat/live tree
   2. devfdt_get_addr...()  - current functions, flat tree only
   3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:01 -06:00
Simon Glass
9d922450aa dm: Use dm.h header when driver mode is used
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 06:57:52 -06:00
Tom Rini
cb33bda44f Merge branch 'master' of git://git.denx.de/u-boot-i2c 2017-05-15 13:01:26 -04:00