Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When CONFIG_OF_PLATDATA is enabled, we cannot use the u-boot,dm-pre-reloc
device tree property since the device tree is not available. However,
dt-platdata.c only includes devices which would have been present in the
device tree, and we can assume that all such devices are needed for SPL.
If they were not needed, they would have been omitted to save space.
So in this case, bind all devices regardless of the u-boot,dm-pre-reloc
setting. This avoids needing to add a DM_FLAG_PRE_RELOC to every driver,
thus affecting U-Boot proper also.
Signed-off-by: Simon Glass <sjg@chromium.org>
The next stage boot loader image and the selected FDT can be post-
processed by board/platform/device-specific code, which can include
modifying the size and altering the starting source address before
copying these binary blobs to their final destination. This might be
desired to do things like strip headers or footers attached to the
images before they were packaged into the FIT, or to perform operations
such as decryption or authentication. Introduce new configuration
option CONFIG_SPL_FIT_IMAGE_POST_PROCESS to allow controlling this
feature. If enabled, a platform-specific post-process function must
be provided.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.
Add an extra Kconfig option to specify the offset of the redundant u-boot
image.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>
Correct the error message in spl_load_image_ext() when image parsing
fails. Instead of "ext4fs_read failed" print "failed to parse image
header".
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
CC: Tom Rini <trini@konsulko.com>
Remove redundant #if defined(CONFIG_SPL_OS_BOOT) statement around
getenv() calls in spl_load_image_ext_os().
The whole function is surrounded by #ifdef CONFIG_SPL_OS_BOOT.
No functional change.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
Acked-by: Guillaume GARDET <guillaume.gardet@free.fr>
When no DTB can be matched successfully to the board that's being used
a list of available FIT-embedded DTBs will be output to the console for
diagnostic purposes. But rather than the contents of the "description"
FDT property a non-existent property was accessed and as a result "NULL"
was output instead of the actual name(s) of the DTB(s). Fix this issue
by using the correct property which is also the exact same property
that's used earlier during the actual board matching process.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Allow configuring the begining of the malloc_f area in SPL.
This patch uses the same CONFIG_MALLOC_F_ADDR established by
the sandbox.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Remove the check for GD_FLG_SPL_INIT in spl_relocate_stack_gd().
The check will always fail. This is because spl_relocate_stack_gd()
is called from ARM's crt0.S and it is called before board_init_r().
The board_init_r() calls spl_init(), which sets the GD_FLG_SPL_INIT
flag.
Note that reserving the malloc area in RAM is not a problem even
if the GD_FLG_SPL_INIT flag is not set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
When loading fit header, it should be loaded to a previous address
aligned to ARCH_DMA_MINALIGN and not 8. Fixing the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
This provides a way to load a FIT containing U-Boot and a selection of device
tree files from UART.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Detect a FIT when loading from NAND and handle it using the
new FIT SPL support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Make sure we continue to use (void *)(unsigned long) for
load_addr].
Signed-off-by: Tom Rini <trini@konsulko.com>
Detect a FIT when loading from a FAT File system and handle it using the
new FIT SPL support.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This provides a way to load a FIT containing U-Boot and a selection of device
tree files from a File system. Making sure that all the reads and writes
are aligned to their respective needs.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Make this still apply with Michal's alignment change for 'fit']
Signed-off-by: Tom Rini <trini@konsulko.com>
sectors field is not being updated when reading fdt from fit image. Because of
this size_of(u-boot.bin) is being read when reading fdt. Fixing it by updating
the sectors field properly.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If bl_len is not aligned it can caused a problem because another code
expects that start is aligned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support loading FIT in SPL for RAM bootmode.
CONFIG_SPL_LOAD_FIT_ADRESS points to address where FIT image is stored
in memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Call this function before passing control from SPL.
For fpga case it is necessary to enable for example level shifters
when bitstream is programmed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The spl_parse_image_header() can return 0 and it is not an error.
Only treat non-zero return value as an error.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When FDT is not present in the image user doesn't get any error what's
wrong. Print error message if LIBCOMMON_SUPPORT is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Seris-cc: uboot
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When defined, SPL will proceed to another boot method
if the image it has loaded does not have a signature.
This is useful if the subsequent boot methods are much
more complex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Allow the spl_parse_image_header() to return value. This is convenient
for controlling the SPL boot flow if the loaded image is corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
The error message "spl: mmc block read error" may come from two
different functions, so we should better annotate the function name
where the error comes from to help debugging.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If CONFIG_SPL_OS_BOOT is enabled and Linux image is not flashed at
RAW_MODE_KERNEL_SECTOR in MMC, spl still assumes that Linux is
available and tries to boot it and hangs. In order to avoid this,
adding a check to verify if parsed image header is of type IH_OS_LINUX.
If it fails then fall back to load u-boot image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In case of #define DEBUG 1 (fordebugging SPL). A bug in
spl_nand_load_image() will be triggered, because it prints
using hw ecc regardless of soft ecc configurations and
initializations.
Signed-off-by: Ahmed Samir <engkhalil86@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some sunxi boards (and presumably also non sunxi boards) u-boot can
be either loaded from a sdcard in a micro-sd slot, or from eMMC.
Print which MMC spl tries to boot from, to help debugging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function spl_parse_image_header() falls back to a raw image
if the U-Boot header is missing and CONFIG_SPL_PANIC_ON_RAW_IMAGE
is undefined. While, mmc_load_image_raw_sector() only accepts a
U-Boot legacy image or an FIT image, preventing us from loading a
raw image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix "warning: cast to pointer from integer of different size".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This provides a way to load a FIT containing U-Boot and a selection of device
tree files. The board can select the correct device tree by probing the
hardware. Then U-Boot is started with the selected device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Since commit fd61d39970:
spl: mmc: add break statements in spl_mmc_load_image()
RAW and FS boot modes are now exclusive again. So, if MMCSD_MODE_RAW fails, the
board hangs. This patch allows to try MMCSD_MODE_FS then.
It has been tested on a beaglebone black to boot on an EXT partition.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As of gcc 5.2.1 for Thumb-1, it is not possible any
more to assign gd from C code, as gd is mapped to r9,
and r9 may now be saved in the prolog sequence, and
restored in the epilog sequence, of any C functions.
Therefore arch_setup_gd(), which is supposed to set
r9, may actually have no effect, causing U-Boot to
use a bad address to access GD.
Fix this by never calling arch_setup_gd() for ARM,
and instead setting r9 in arch/arm/lib/crt0.S, to
the value returned by board_init_f_alloc_reserve().
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to support boot from multiple devices through board_boot_order,
it's necessary to use the block number of a device.
The use of a hard-coded 0 for the device number also creates a need
to re-order block devices for use in SPL like this:
http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195
Signed-off-by: Eric Nelson <eric@nelint.com>
For a simple static string, use panic_str() which prevents calling
printf needlessly.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is risky to have two different functions with much the same code. Future
authors may update one but not the other. It is hard to see which parts are
the same and which are different.
Unify the functions and drop the differences that are not really needed.
Note that one puts() becomes printf() as Tom mentioned that this does not
affect image size:
https://patchwork.ozlabs.org/patch/537276/
Note: It would be better to have an empty printf() and avoid the #ifdef for
CONFIG_SPL_LIBCOMMON_SUPPORT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
The 'p' suffix makes it more obvious that we are dealing with a pointer
to a (pointer) value that will be returned to its caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Since commit 4188ba3 we get the following warning on rockchip boards:
common/spl/spl_mmc.c:31:24: warning: ‘mmc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
count = mmc->block_dev.block_read(0, sector, 1, header);
^
common/spl/spl_mmc.c:251:14: note: ‘mmc’ was declared here
struct mmc *mmc;
Correct this by move the variable init earlier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.
Make SPL take into account the correct mmc device.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we support alternative boot devices, it can sometimes be
unclear which boot devices was actually used. Provide a function to
announce which boot devices are attempted during boot.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce spl_boot_list array, which defines a list of boot devices
that SPL will try before hanging. By default this list will consist
of only spl_boot_device(), but board_boot_order() can be overridden
by board code to populate the array with custom values.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactor spl image load code out of board_init_r and into its own
function. This is a preparation for supporting alternative boot
devices.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Get rid of emmc boot code duplication in spl_mmc_load_image() using a switch
case fallthrough into MMCSD_MODE_RAW. Since the #ifdef CONFIG_SUPPORT_EMMC_BOOT
check is not really necessary, remove it in the process.
No functional changes.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move the code that handles fs boot out of spl_mmc_load_image() and into its
own function to reduce the #ifdef complexity of spl_mmc_load_image().
No functional changes.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement defaults for the raw partition image loading so that the #ifdef
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION in spl_mmc_load_image() will no
longer be necessary.
This change makes it possible for mmc_load_image_raw_partition() and
mmc_load_image_raw_sector() to coexist.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement default versions of falcon mode functions to make the
CONFIG_SPL_OS_BOOT check in spl_mmc_load_image() unnecessary, thus reducing
its #ifdef complexity.
No functional changes.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simplify spl_mmc_load_image() code by moving the part that finds the mmc device
into its own function spl_mmc_find_device(), available in two flavors: DM and
non-DM.
This refactor fixes a bug in which an error in the device location sequence
does not necessarily aborts the rest of the code. With this refactor, we fail
the moment there is an error.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The original intention of the mmc load_image() function was to try multiple
boot modes before failing. This is evident by the lack of break statements
in the switch, and the following line in the default case:
puts("spl: mmc: no boot mode left to try\n");
This implementation is problematic because:
- The availability of alternative boot modes is very arbitrary since it
depends on the specific order of the switch cases. If your boot mode happens to
be the first case, then you'll have a bunch of other boot modes as alternatives.
If it happens to be the last case, then you have none.
- Opting in/out is tied to config options, so the only way for you to prevent an
alternative boot mode from being attempted is to give up on the feature completely.
- This implementation makes the code more complicated and difficult to
understand.
Address these issues by inserting a break statements between the cases to make the
function try only one boot mode.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove code duplication in spl_nand_load_image().
No functional changes.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Add back cast to unsigned long of spl_image.load_addr]
Signed-off-by: Tom Rini <trini@konsulko.com>
malloc_simple uses a part of the stack as heap, initially it uses
SYS_MALLOC_F_LEN bytes which typically is quite small as the initial
stacks sits in SRAM and we do not have that much SRAM to work with.
When DRAM becomes available we may switch the stack from SRAM to DRAM
to give use more room. This commit adds support for also switching to
a new bigger malloc_simple heap located in the new stack.
Note that this requires spl_init to be called before spl_relocate_stack_gd
which in practice means that spl_init must be called from board_init_f.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
spl_relocate_stack_gd only gets called from arch/arm/lib/crt0.S which
clears the bss directly after calling it, so there is no need to clear
it from spl_relocate_stack_gd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch introduces the option to boot from a MMC card parition with
an offset. This can be done by using both defines together:
define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR ((160 << 10) / 512)
The example above loads the main U-Boot at offset 160KiB from the MMC
partition 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Tom Rini <trini@konsulko.com>
As a debug option, add positive confirmation that SPL has completed
execution. This can help with diagnosing the location of unexpected hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an spl_init() function that does basic init such that board_init_f() can
use simple malloc(), device tree and driver model. Each one is set up only
if enabled for SPL.
Note: We really should refactor SPL such that there is a single
board_init_f() and rename the existing weak board_init_f() functions
provided by boards, calling them from the single board_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows using only one of either raw or fs mode for SPL mmc boot, without
the need to have provisions for the other. In particular, a device may have
U-Boot installed on a file system on the mmc, without ever needing to read
U-Boot from raw memory. Thus, there is no reason to provide a sector or
partition for raw mode. This allows this behaviour and still provides a robust
fallback mechanism in case provisions for both modes are defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces a distinction between return codes that are read bytes counts
and errors. Read bytes counts are erroneous when null (no data was read) while
errors are erroneous when non-null.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Tim Harvey <tharvey@gateworks.com>
91199f4a5a broke mmc based Falcon mode.
The block_read function returns the number of blocks read thus the error
check needs to look for a return of 0 blocks read.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
During the Kconfig conversion one of the changes was missed.
CONFIG_SPL_STACK_R should be CONFIG_SPL_STACK_R_ADDR since we want the
address.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This refactors spl_mmc_load_image to use a switch/case structure and easier
to understand spl_start_uboot checks. This also introduces some more automatic
fallback on the next mmc boot mode as long as it keeps failing.
Lines that go beyond 80 chars are also reduced by reducing the number of tabs.
Debug and error strings are refctored to match a common style.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
[trini: Fix a thinko in the SPL_EXT_SUPPORT + SPL_OS conversion, make part be
__maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
introduce CONFIG_SPL_PANIC_ON_RAW_IMAGE.
An SPL which define this will panic() if the
image it has loaded does not have a mkimage
signature.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
At present SPL uses a single stack, either CONFIG_SPL_STACK or
CONFIG_SYS_INIT_SP_ADDR. Since some SPL features (such as MMC and
environment) require a lot of stack, some boards set CONFIG_SPL_STACK to
point into SDRAM. They then set up SDRAM very early, before board_init_f(),
so that the larger stack can be used.
This is an abuse of lowlevel_init(). That function should only be used for
essential start-up code which cannot be delayed. An example of a valid use is
when only part of the SPL code is visible/executable, and the SoC must be set
up so that board_init_f() can be reached. It should not be used for SDRAM
init, console init, etc.
Add a CONFIG_SPL_STACK_R option, which allows the stack to be moved to a new
address before board_init_r() is called in SPL.
The expected SPL flow (for CONFIG_SPL_FRAMEWORK) is documented in the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
For version 1:
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
executing "tools/buildman/buildman mpc5xx" drops this warning:
common/spl/spl_nor.c: In function 'spl_nor_load_image':
common/spl/spl_nor.c:26:10: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Some boards have a special way of loading U-Boot that does not fit with
the existing SPL code. For example sunxi uses an 'FEL' mode where U-Boot
is loaded over USB. Add a CONFIG option and boot mode for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Microblaze currently doesn't use printf in SPL. So this one line was the only
reference to it and resulted in the printf functionality to be pulled in.
Exceeding the 4k size limit. Lets change the printf back to puts so that
Microblaze is fixed again. The only drawback is that the detected boot-device
number will not be printed. But this message alone should be helpful enough
to get an idea where the boot process is broken.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>