The OneNAND SPL used on PXA is slightly obscure. Due to the OneNAND limitation,
where we have only the first 1KiB of the OneNAND available upon power-up as a
memory-mapped area, from which the CPU starts executing, we place only the most
essential code into this first 1KiB . This code copies the rest of the SPL into
SRAM and jumps to it. This code is stored in section .text.0 .
The rest of the SPL is stored in section .text.1 . When running the OBJCOPY on
the SPL, it will preserve only .text section, but the .text.0 and .text.1 are
stripped away from the result, thus making the SPL binary empty. The patch adds
additional -j parameters to the OBJCOPY for PXA during the SPL build, which will
preserve the .text.0 and .text.1 sections.
Moreover, this patch also adds missing functions into the .text.0 section, since
otherwise the PXA270 with 1KiB-window OneNAND won't be able to boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
GPIO dummy routines are required for fdt build, may be removed
these dependencies once the u-boot fdt is fully optimized.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch provides a basic fdt support for zynq u-boot.
zynq-7000.dtsi-> initial arch dts file
zynq-zed.dts -> initial zed board dts file
more devices should be added in subsequent patches.
u-boot build: once configuring of a board done
for building dtb with zynq-zed.dts as an input
zynq-uboot> make DEVICE_TREE=zynq-zed
Enabled CONFIG_OF_SEPARATE for building dtb separately.
There is a new binary called u-boot-dtb.bin which is a u-boot
with devicetree supported.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.
Added this functionality on board_late_init as it's not
needed for normal initializtion part.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The toolchain sets __aarch64__ for both LE and BE. In the case of
posix_types.h we cannot reliably use config.h as that will lead to
problems. In the case of byteorder.h it's clearer to check the EB flag
being set in either case instead.
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Tom Rini <trini@ti.com>
Amended by Albert ARIBAUD <albert.u.boot@aribaud.net> to
actually remove the config.h include from the posix_types.h
files, with permission from Tom Rini.
Relocation code based on a patch by Scott Wood, which is:
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Feng <fenghua@phytium.com.cn>
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The enable_fec_anatop_clock method should be available for all MX6
variant as it is not MX6 SoloLite specific. This moves the code out of
the #ifdef/#endif and we make it conditional to CONFIG_FEC_MXC
instead.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The macro allows easy setting in per-pin, as for example:
,----
| imx_iomux_v3_setup_pad(MX6_PAD_NANDF_D1__GPIO_2_1 | MUX_MODE_SION);
`----
The IOMUX_CONFIG_SION allows for reading PAD value from PSR register.
The following quote from the datasheet:
,----
| ...
| 28.4.2.2 GPIO Write Mode
| The programming sequence for driving output signals should be as follows:
| 1. Configure IOMUX to select GPIO mode (Via IOMUXC), also enable SION if need
| to read loopback pad value through PSR
| 2. Configure GPIO direction register to output (GPIO_GDIR[GDIR] set to 1b).
| 3. Write value to data register (GPIO_DR).
| ...
`----
This fixes the gpio_get_value to properly work when a GPIO is set for
output and has no conflicts.
Thanks for Benoît Thébaudeau <benoit.thebaudeau@advansee.com>, Fabio
Estevam <fabio.estevam@freescale.com> and Eric Bénard
<eric@eukrea.com> for helping to properly trace this down.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.
Also, as the timer is still not available when arch_cpu_init() is called, we
need to call it later at board_postclk_init() phase.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since ROM may modify the LDO ramp up time according to fuse setting,
it is safer to reset the ramp up field to its default value of 00:
00: 64 cycles of 24MHz clock;
01: 128 cycles of 24MHz clock;
02: 256 cycles of 24MHz clock;
03: 512 cycles of 24MHz clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds dts support for SMDK5420.
exynos5.dtsi created is a common file which has the nodes common
to both 5420 and 5250.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds code in pinmux and gpio framework to support Exynos5420.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch intends to add DDR3 initialization code for Exynos5420.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add dmc and phy_control register structure for 5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add structure for power register for Exynos5420
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds base addresses of various IPs and controllers required for
Exynos5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Create a common board.c file for all functions which are common across
all EXYNOS5 platforms.
exynos_init function is provided for platform specific code.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50 300MHz
OPP100 600MHz
OPP120 720MHz
OPPTB 800MHz
OPPNT 1000MHz
According to the latest DM following is the OPP table dependencies:
VDD_CORE VDD_MPU
OPP50 OPP50
OPP50 OPP100
OPP100 OPP50
OPP100 OPP100
OPP100 OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz
Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The CPU complex reset masks are not matching with the datasheet for
the CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET/CLR_0 registers. For both T20
and T30 the register consist of groups of 4 bits, with one bit for
each CPU core. On T20 the 2 high bits of each group are always stubbed
as there is only 2 cores.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swrren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
PLLX no longer has the CPCON field on Tegra114, so do not attempt to
program it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The M, N and P width have been changed from Tegra30. The maximum value
for N is limited to 255. So, the tegra_pll_x_table for Tegra114 should
be set accordingly.
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Reviewed-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs.
We put SDRAM in selfresh mode before watchdog reset, removing
potential freezes.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache
Signed-off-by: Huang yongcai <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:
"Controls the frequency of the ethernet reference clock.
- 00 - 25MHz
- 01 - 50MHz
- 10 - 100MHz
- 11 - 125MHz"
Current logic does not handle the 25MHz case correctly, so fix it.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Move setup_sata function definition from platform file nitrogen6x.c
to arch/arm/imx-common/sata.c to avoid code duplication.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.
All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
MX6Q - for boards targeting i.MX6Q or i.MX6D
MX6DL - for boards targeting i.MX6DL
MX6S - for boards targeting i.MX6S
MX6QDL - for boards that support any of the above with
run-time detection
Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
