Commit Graph

11665 Commits

Author SHA1 Message Date
Tom Rini
f3b623fa52 Merge git://git.denx.de/u-boot-marvell 2018-03-30 18:18:22 -04:00
Tom Rini
0ca0a546b1 Merge git://git.denx.de/u-boot-riscv 2018-03-30 18:16:56 -04:00
Mark Kettenis
bdca661ecc arm64: mvebu: a8k: Add distro boot support
The various load address values are taken from the a37xx configuration
and match the dowstream 'u-boot-2017.03-armada-17.10' release where
appropriate.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30 12:52:48 +02:00
Rick Chen
d58717e425 riscv: ae250: Support DT provided by the board at runtime
Enable CONFIG_OF_BOAD to support delivery dtb to u-boot
at run time instead of embedded.

There are two methods to delivery dtb.
 1 Pass from loader:
   When u-boot boot from RAM, gdb or loader can pass dtb
   via a2 to u-boot dynamically. Of course gdb or loader
   shall be in charge of dtb delivery.

 2 Configure CONFIG_SYS_FDT_BASE:
   It can be configured as RAM or ROM base statically,
   no mater u-boot boot from RAM or ROM.
   If it was configured as ROM base, dtb can be burned
   into ROM(spi flash) by spi driver.

Meanwhile remove CONFIG_SKIP_LOWLEVEL_INIT which is
useless in nx25-ae250 configuration.

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
2018-03-30 13:13:56 +08:00
Rick Chen
095c9f35d5 mmc: ftsdc010: Migrate CONFIG_FTSDC010_SDIO to Kconfig
Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
2018-03-30 13:13:45 +08:00
Rick Chen
88a0b7694f Drop CONFIG_FTSDC010_NUMBER
CONFIG_FTSDC010_NUMBER was not used anymore,
can be removed now.

So CONFIG_FTSDC010_NUMBER
can also be removed from config_whitelist.txt.

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
2018-03-30 13:13:45 +08:00
Mark Kettenis
d928695ed6 rockchip: rk3399: set fdtfile
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-28 23:44:59 +02:00
Tom Rini
81cf7c8d45 Merge git://git.denx.de/u-boot-ubi 2018-03-25 12:02:13 -04:00
Petr Vorel
c0ce4ceaba Convert CONFIG_UBI_SILENCE_MSG to Kconfig
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
2018-03-24 06:37:25 +01:00
Petr Vorel
afb6fda2ae Convert CONFIG_UBIFS_SILENCE_MSG to Kconfig
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
  long long x, y;

Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.

Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
2018-03-24 06:37:10 +01:00
Michal Simek
348dbf4368 arm64: zynqmp: Remove ep108 board
ZynqMP Emulation board is no longer tested and there is no reason to
keep maintaining it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23 09:34:59 +01:00
Vipul Kumar
fce0a6b521 arm64: zynqmp: Changed scratch address used by the alternate memory test
This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the
accessible DDR address used by alternate memory test.
Before this, 0xfffc0000 address was used, which is the OCM
address and not enabled in MMU table. So, whenever trying
to access 0xfffc0000 address, got Synchronous Abort exception.

After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate
memory test is working fine.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23 09:34:44 +01:00
Tom Rini
b0af10443a Merge git://git.denx.de/u-boot-net 2018-03-22 16:35:43 -04:00
Lokesh Vutla
d6d8c4d4cc configs: omapl138: Enable DM and DT
Enable Driver Model and Device-tree support for omapl138 board
in U-Boot. Also enable DM_SERIAL and DM_I2C.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-03-22 16:32:31 -04:00
David Lechner
dc73483a12 davinci: omapl138_lcdk: fix PLL0 frequency
commit 1601dd97ed ("davinci: omapl138_lcdk: increase PLL0 frequency")
changed the PLL0 frequency to 456MHz, which is needed for the LCDC IP
block. However, in doing so, it caused the PLLOUT clock to be outside
of the allowable specifications given in the OMAP-L138 data sheet. (It
says PLLOUT must be 600MHz max). It also uses a PLLM value outside of
the range given in the TRM (it says PLLM must in the range 0 to 0x1f).

So here is what we have currently:

PLLOUT = 24 / (0 + 1) * (37 + 1) = 912MHz (out of spec)
         ^     ^         ^
       CLKIN PREDIV    PLLM (out of spec)

input to PLLDIVn = 912 / (1 + 1) = 456MHz (desired result)
                    ^     ^
                 PLLOUT POSTDIV

This changes the PLLM value to 18 and the POSTDIV value to 0 so that
PLLOUT is now within specification but we still get the desired
result.

PLLOUT = 24 / (0 + 1) * (18 + 1) = 456MHz (within spec)
         ^     ^         ^
       CLKIN PREDIV     PLLM

input to PLLDIVn = 456 / (0 + 1) = 456MHz (desired result)
                    ^     ^
                 PLLOUT POSTDIV

Fixes: 1601dd97ed ("davinci: omapl138_lcdk: increase PLL0 frequency")
Signed-off-by: David Lechner <david@lechnology.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
2018-03-22 16:32:24 -04:00
Calvin Johnson
a802d1e268 configs: ls1012a: add pfe configuration for LS1012A
Add configurations for PFE.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:31 -05:00
Calvin Johnson
7ab16479e1 board: freescale: ls1012ardb: enable network support on ls1012ardb
This patch enables ethernet support for ls1012ardb.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:30 -05:00
Álvaro Fernández Rojas
ee1f79b738 mips: bmips: add support for bcm6318 usb
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
35e03f0011 mips: bmips: add support for bcm63268 usb
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
ad7f6ed41e mips: bmips: add support for bcm6362 usb
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
f94e360614 mips: bmips: add support for bcm6328 usb
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
fc5cf3a0c7 mips: bmips: add support for bcm6368 usb
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
e8dad2e739 mips: bmips: add support for bcm6358 usb
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
d51aaf84cb mips: bmips: add support for bcm6348 usb
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
9d466f2fe1 MIPS: add BMIPS Netgear DGND3700v2 board
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
8f240a3b45 MIPS: add support for Broadcom MIPS BCM6362 SoC family
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-03-21 23:23:13 +01:00
Tom Rini
9c0e2f6ed3 Merge git://git.denx.de/u-boot-fsl-qoriq 2018-03-20 18:39:27 -04:00
Vinitha V Pillai
3386c73d46 LS2088ARDB: Secure Boot: Fix fall back option failure
Fix NOR, SD and QSPI fallback option in case of secure boot failure.

Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20 08:30:52 -07:00
Ashish Kumar
c1c597e8a8 armv8: ls1088aqds: Add IFC-NOR as boot source for LS1088
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.

Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20 08:27:13 -07:00
Ashish Kumar
b555e293b3 armv8: ls1088qds: Remove CONFIG_ from local defines for FPGA
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20 08:25:34 -07:00
Patrick Delaunay
f8598d9815 board: st: add generic board for STM32MP1 family
Add first support for STM32MP157C-ED1 board with "Basic" boot chain
1/ Boot Rom: load SPL with STM32 image header in SYSRAM
2/ SPL: power up and initialize the DDR and load U-Boot image
        from SDCARD in DDR
3/ U-Boot: search and load extlinux.conf in SDCARD
           (DISTRO activated)

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19 16:14:22 -04:00
yannick fertre
92eac5848f stm32f7: board: add splash screen
Support several pixel format (8bits, 16bits, 24bits & 32bits).
Add new file st_logo_data.h which contains logo
stmicroelectronics_uboot_logo_8bit_rle.bmp.

Signed-off-by: yannick fertre <yannick.fertre@st.com>
2018-03-19 11:01:04 +01:00
Tom Rini
6f6b7cfa89 Convert all of CONFIG_CONS_INDEX to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16 10:28:52 -04:00
Madan Srinivas
1c49caf34c configs: k2l: Updates u-boot env to install secure boot monitor
This patch updates the default u-boot env for K2L HS devices
to install the secure boot monitor and load the fitImage during
boot.

Signed-off-by: Madan Srinivas <madans@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-03-16 09:42:39 -04:00
Masahiro Yamada
27fbdcdefd ARM: uniphier: change load addresses for bigger kernel image
The kernel size is getting bigger and bigger.  Because the Android
common kernel is even bigger than the vanilla one, so images overlap
in the current memory layout.

Adjust the load address for a bigger kernel image.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-15 22:43:35 +09:00
Masahiro Yamada
34be347999 ARM: uniphier: increase the firmware size in update command environment
If a bigger EL32 is used, fip.bin can be larger than the currently
assumed boot firmware size.  Adjust the update commands.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-15 22:41:31 +09:00
Tom Rini
b75643ad0a Merge git://git.denx.de/u-boot-sunxi 2018-03-14 13:27:14 -04:00
Derald D. Woods
b6e2543cf9 ARM: omap3: evm: Sync with omap3_beagle configuration
This commit does the following for OMAP3 EVM:

- Track omap3_beagle changes where possible
- Remove CONFIG_SYS_MPUCLK and CONFIG_MTD which are not needed for the
  default board configuration to work.
- Remove CONFIG_SPL_SYS_MALLOC_SIMPLE and CONFIG_SYS_MALLOC_F_LEN from
  default config. CONFIG_SYS_MALLOC_F_LEN=0x400 is set by configuration
  automatically. [allows board to boot with SERIAL_SEARCH_ALL=y]
- Use updated NAND layout:

	device nand0 <omap2-nand.0>, # parts = 6

	#: name		size			offset
	-------------------------------------------------
	0: spl		0x00080000(512k)	0x00000000
	1: u-boot	0x001e0000(1920k)	0x00080000
	2: u-boot-env	0x00020000(128k)	0x00260000
	3: dtb		0x00020000(128k)	0x00280000
	4: kernel	0x00600000(6m)		0x002a0000
	5: rootfs	0x0f760000(-)		0x008a0000
	-------------------------------------------------

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-03-13 21:59:28 -04:00
Derald D. Woods
d233ccb1d8 ARM: omap3: beagle: Enable DM_SERIAL, update distro usage and NAND layout
This commit does the following for BeagleBoard{-xM}:

- Enable DM_SERIAL which also enables SPL_DM_SERIAL
- Misc. config updates in support of DM_SERIAL
- Use updated NAND layout (BeagleBoard):

	device nand0 <omap2-nand.0>, # parts = 6

	#: name		size			offset
	-------------------------------------------------
	0: spl		0x00080000(512k)	0x00000000
	1: u-boot	0x001e0000(1920k)	0x00080000
	2: u-boot-env	0x00020000(128k)	0x00260000
	3: dtb		0x00020000(128k)	0x00280000
	4: kernel	0x00600000(6m)		0x002a0000
	5: rootfs	0x0f760000(-)		0x008a0000
	-------------------------------------------------

- Use MMC and UBIFS support from config_distro_bootcmd.h
- Use LEGACY_MMC and NAND support defined in omap3_beagle.h

[MMC(0:1)/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-mmc-fat
label omap3-beagle-mmc-fat
	kernel /zImage
	fdt /omap3-beagle.dtb
	append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------

[LEGACY_MMC(0:2)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-mmc-ext4
label omap3-beagle-mmc-ext4
	kernel /boot/zImage
	fdt /boot/omap3-beagle.dtb
	append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------

[UBIFS(ubi0:rootfs)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-nand-ubifs
label omap3-beagle-nand-ubifs
	kernel /boot/zImage
	fdt /boot/omap3-beagle.dtb
	append console=ttyO2,115200n8 root=ubi0:rootfs rw ubi.mtd=rootfs rootfstype=ubifs rootwait
---8<-------------------------------------------------------------------

The board's 'bootcmd' can also be overridden with:

	CONFIG_BOOTCOMMAND="run findfdt; run mmcboot"
	CONFIG_BOOTCOMMAND="run findfdt; run nandboot"
	CONFIG_BOOTCOMMAND="run findfdt; run ramboot"

		or

	CONFIG_BOOTCOMMAND="run findfdt; run somethingelse"

The use of 'run findfdt' is required.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-03-13 21:59:27 -04:00
Patrice Chotard
aa5e3e22f4 board: stm32: switch to DM STM32 timer
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.

Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx

Enable DM STM32_TIMER for STM32F4/F7 and H7.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-03-13 21:45:37 -04:00
Klaus Goger
0c8e0b319f rockchip: add text_offset to kernel_addr_r on aarch64 platforms
Booting a aarch64 Linux kernel requires the image to be placed
text_offset bytes from a 2MB aligned address.
See https://www.kernel.org/doc/Documentation/arm64/booting.txt

booti_setup() takes care about this alignment and will relocate the
image if not properly aligned with memmove(). This can require up
to double the size of the loaded image and therefore accidentally
overwrite content placed there (i.e ramdisk_addr_r) for large kernel
images.

By adding text_offset to the default kernel_addr_r we can prevent that
from happening for kernels larger 18MB and also save a few cycles.

We can assume a text_offset of 0x80000 for most cases, all others will be
handled by booti_setup() anyway.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13 18:12:35 +01:00
Stefan Mavrodiev
b30c419040 Move CONFIG_PHY_ADDR to Kconfig
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
	- edb9315a	- CONFIG_PHYLIB is not enabled. Entry is
			  deleted.

	- ds414		- CONFIG_PHYLIB is in incompatible format:
			  { 0x1, 0x0 }. This entry is also deleted.

	- devkit3250	- The PHY_ADDR is in hex format (0x1F).
			  Manually CONFIG_PHY_ADDR=31 is added in
			  the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 22:36:33 +05:30
Tuomas Tynkkynen
b996b7d426 ARM: Drop unreferenced CONFIG_* defines named after boards
The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_AT91SAM9263EK
CONFIG_AT91SAM9RLEK
CONFIG_BARIX_IPAM390
CONFIG_BOARD_H2200
CONFIG_EP9301
CONFIG_KZM_A9_GT
CONFIG_PICOSAM
CONFIG_PLATINUM_PICON
CONFIG_PLATINUM_TITANIUM
CONFIG_PM9261
CONFIG_PM9263
CONFIG_PM9G45
CONFIG_SIEMENS_DRACO
CONFIG_SIEMENS_PXM2
CONFIG_SIEMENS_RUT
CONFIG_SMDKC100
CONFIG_SMDKV310
CONFIG_STM32F4DISCOVERY

Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-03-09 09:23:10 -05:00
Tuomas Tynkkynen
17796171be ARM: Drop unreferenced CONFIG_* defines named after SoCs
The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_ARM926EJS
CONFIG_CPUAT91
CONFIG_EXYNOS5800
CONFIG_SYS_CORTEX_R4

Most of them are config symbols named after the respective SoCs which
seems to have been a standard practice at some point.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-03-09 09:23:10 -05:00
Tuomas Tynkkynen
c604f47a80 MIPS: Drop unreferenced CONFIG_* defines
The following config symbols are only defined once and never referenced
anywhere else:

CONFIG_DBAU1X00
CONFIG_PB1X00

Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-03-09 09:23:10 -05:00
Mario Six
d38826a3dc treewide: Fix gdsys mail addresses
The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.

Also, Dirk's address was wrong in one place; fix that as well.

Signed-off-by: Mario Six <six@gdsys.cc>
2018-03-09 09:23:10 -05:00
Tuomas Tynkkynen
b771f0b126 ARM: qemu-arm: Increase CONFIG_SYS_CBSIZE
CONFIG_SYS_CBSIZE determines the maximum length of the kernel command
line, and the default value of 256 is too small for booting some Linux
images in the wild.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2018-03-09 09:23:10 -05:00
Adam Ford
61ec4e0742 omap3_logic: Remove unnecessary undefs
Due to evolution of the MMC driver and better support, let's
remove unnecessary undefs.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-03-05 10:16:29 -05:00
Adam Ford
24c9309254 ti_armv7_omap: Remove comment remnant
With the migration to Kconfig, the I2C block no longer exists in here.
Let's clean up the comment.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-03-05 10:16:29 -05:00
Faiz Abbas
b432b1ebdf spl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the U-boot CONFIG
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.

This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-03-05 10:06:05 -05:00