There are some differences between CoreNet (P2040, P3041, P5020, P4080)
and and non-CoreNet (P1017, P1023) based SoCs in what features exist and
the memory maps.
* Rename various immap defines to remove _CORENET_ if they are shared
* Added P1023/P1017 specific memory offsets
* Only setup LIODNs or LIODN related code on CORENET based SoCs
(features doesn't exist on P1023/P1017)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards
pretty much do the same thing. The only variations are in how many
controllers or DIMMs per controller exist. To make this work we
standardize on the names of the SPD_EEPROM_ADDRESS defines based on the
use case of the board.
We allow boards to override get_spd to either do board specific fixups
to the SPD data or deal with any unique behavior of how the SPD eeproms
are wired up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the include of mpc85xx/u-boot-nand.lds to utilize
CONFIG_SYS_LDSCRIPT rather than having an explicit config.mk
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Read MAC address from EEPROM. Add hwconfig settings.
Modified the default othbootargs to include the cache-sram-size
parameter. This parameter is needed as the L2 as SRAM is ON by
default in the P2020RDB kernel and used by the Gianfar driver.
Also cleanup some of the boot commands.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We enable SDHC_CD and SDHC_WP signals (pin muxed with GPIO8 & GPIO9
respectively).
We enable EXT2, FAT, and parition support for both MMC & USB configs.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.
Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the PCIe address map to match standard FSL memory map.
Additionally, fix the TLBs so the cover the PCIe address space properly
so cards plugged in like an e1000 work correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If no Flash is connected to cs1, Linux crashes, because
reg entries are not correct adapted.
Following fix is needed:
- swap base addresses in CONFIG_SYS_FLASH_BANKS_LIST, as
flash bank 1 is on chipselect 0 and flash bank 2 on
chipselect 1
- call fdt_fixup_nor_flash_size() from ft_board_setup()
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
Currently, pixis_reset altbank does not work properly. This patch
uses the correct mask to boot into the alternate bank.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.
This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.
This patch is tested with compilation for armada100 and guruplug.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Board EEPROM is used to read/save Ethernet MAC addresses.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Some VCT boards lacks the support of networking or USB.
Additionally that support is disabled in small image
configurations.
If CONFIG_CMD_NET should not used the CONFIG_CMD_NFS option
have to be disabled too. Otherwise the linker fails with
unresolved symbols.
If CONFIG_VCT_SMALL_IMAGE is set than CONFIG_CMD_NET and
CONFIG_CMD_USB are disabled at the end of vct.h.
This is not adequate because CONFIG_CMD_USB enables additional
options and the linker fails again with unresolved symbols.
This patch adds an early check against CONFIG_VCT_SMALL_IMAGE
so the additional options are only enabled if they are really
needed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Using hwconfig to turn on/off ECC, without re-compiling.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.
This patch supports the following functions:
- 256MB DDR3-SDRAM
- SPI ROM
- Ethernet
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
