Commit Graph

11 Commits

Author SHA1 Message Date
Reinhard Arlt
2b22460956 CPCI750: Add CPCI-HD/2 support
This patch adds support for the esd CPCI-HD/2 board to u-boot for CPCI-CPU/750.
As the primary devices on the CPCI-HD/2 board are connected to device 1 and 3,
the device must be swapped.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
2012-03-18 20:10:02 +01:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Steven A. Falco
36c2d3062e Add a hook to allow board-specific PIO mode setting.
This patch adds a hook whereby a board-specific routine can be called to
configure hardware for a PIO mode.  The prototype for the board-specific
routine is:

	int inline ide_set_piomode(int pio_mode)

ide_set_piomode should be prepared to configure hardware for a pio_mode
between 0 and 6, inclusive.  It should return 0 on success or 1 on failure.

Signed-off-by: Steven A. Falco <sfalco@harris.com>
2008-08-21 01:31:04 +02:00
Steven A. Falco
9571b84cb1 Replace enums in ata.h with an include of libata.h
This patch removes some enums from ata.h and replaces them with an
include of libata.h.  This way, we eliminate duplicated code, and
prevent errors whereby the different versions could be out of sync.

Signed-off-by: Steven A. Falco <sfalco@harris.com>
2008-08-21 01:20:45 +02:00
Wolfgang Denk
3162eb8369 Minor coding style cleanup. 2007-05-15 23:38:05 +02:00
mushtaq khan
66d9dbec1c Add driver for S-ATA-controller on Intel processors with South
Bridge, ICH-5, ICH-6 and ICH-7. 

Implementation:

1. Code is divided in to two files. All functions, which are
   controller specific are kept in "drivers/ata_piix.c" file and
   functions, which are not controller specific, are kept in
   "common/cmd_sata.c" file.

2. Reading and Writing from the S-ATA drive is done using PIO method.

3. Driver can be configured for 48-bit addressing by defining macro
   CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
   addressing.

4. S-ATA read function is hooked to the File system, commands like
   ext2ls and ext2load file can be used. This has been tested.

5. U-Boot command "SATA_init" is added, which initializes the S-ATA
   controller and identifies the S-ATA drives connected to it.

6. U-Boot command "sata" is added, which is used to read/write, print
   partition table and get info about the drives present. This I have
   implemented in same way as "ide" command is implemented in U-Boot.

7. This driver is for S-ATA in native mode.

8. This driver does not support the Native command queuing and
   Hot-plugging.

Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
2007-05-15 23:25:37 +02:00
wdenk
42dfe7a184 Code cleanup; make several boards compile & link. 2004-03-14 22:25:36 +00:00
wdenk
c40b295682 * Patch by Rune Torgersen, 27 Feb 2004:
- Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
  - Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
  - Added support for 64bit strtoul (CFG_64BIT_STRTOUL)

* Patch by Masami Komiya, 27 Feb 2004:
  Fix rarpboot: add autoload by NFS

* Patch by Dan Eisenhut, 26 Feb 2004:
  fix flash_write return value in saveenv

* Patch by Stephan Linz, 11 Dec 2003
  expand config.mk to avoid trigraph warnings on NIOS

* Rename "BMS2003" board into "HMI10"
2004-03-13 23:29:43 +00:00
wdenk
a522fa0e7c * Make BMS2003 use a separate config file to avoid #ifdef mess;
add I2C support; add support for DS1337 RTC

* Add CompactFlash support  for BMS2003 board

* Add support for status LED on BMS2003 board
2004-01-04 22:51:12 +00:00
wdenk
9fd5e31fe0 * Patch by Pierre Aubert, 24 Nov 2003:
- add a return value for the fpga command
  - add ide_preinit() function called in ide_init if CONFIG_IDE_PREINIT
    is defined. If ide_preinit fails, ide_init is aborted.
  - fix an endianess problem in fat.h
2003-12-07 23:55:12 +00:00
wdenk
fe8c2806cd Initial revision 2002-11-03 00:38:21 +00:00