Commit Graph

23 Commits

Author SHA1 Message Date
Jean-Christophe PLAGNIOL-VILLARD
00b1883a4c drivers/mtd: Move conditional compilation to Makefile
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:42 +02:00
William Juul
5e1dae5c3d Fixing coding style issues
- Fixing leading white spaces
 - Fixing indentation where 4 spaces are used instead of tab
 - Removing C++ comments (//), wherever I introduced them

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:17 -05:00
William Juul
cfa460adfd Update MTD to that of Linux 2.6.22.1
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.

This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.

MAKEALL ppc/arm has some issues:
 * DOC/OneNand/nand_spl is not building (I have not tried porting
   these parts, and since I do not have any HW and I am not familiar
   with this code/HW I think its best left to someone else.)

Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
 cpu/ppc4xx/ndfc.c
 cpu/arm926ejs/davinci/nand.c
 board/delta/nand.c
 board/zylonite/nand.c

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:15 -05:00
Wolfgang Denk
5475412063 TQM85xx: fix typo introduce by commit ffbb5cb9
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-31 17:02:14 +02:00
Detlev Zundel
ffbb5cb942 tqm85xx: Demystify 'DK: !!!' comment
Signed-off-by: Detlev Zundel <dzu@denx.de>
2008-07-20 23:07:42 +02:00
Wolfgang Denk
d0ff51ba5d Code cleanup: fix old style assignment ambiguities like "=-" etc.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-14 15:19:07 +02:00
Wolfgang Denk
9b55a25369 Fix some more print() format errors.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-11 01:16:00 +02:00
Wolfgang Denk
c8a3b109f0 Cleanup out-or-tree building for some boards (.depend)
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:49:18 +02:00
Wolfgang Denk
e093a24762 Coding Style Cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-06-28 23:34:37 +02:00
Becky Bruce
9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00
Wolfgang Denk
cdeb62e20d Merge branch 'master' of git://www.denx.de/git/u-boot-fdt 2008-06-11 22:30:47 +02:00
Kumar Gala
859a86a25c 85xx/86xx: Move to dynamic mgmt of LAWs
With the new LAW interface (set_next_law) we can move to letting the
system allocate which LAWs are used for what purpose.  This makes life
a bit easier going forward with the new DDR code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-11 01:52:23 -05:00
Wolfgang Grandegger
e8cc3f04b1 TQM85xx: Change memory map to support Flash memory > 128 MiB
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) Flash
memory. The current memory map only supports up to 128 MiB Flash.
This patch adds the configuration option CONFIG_TQM_BIGFLASH. If
set, up to 1 GiB flash is supported. To achieve this, the memory
map has to be adjusted in great parts (for example the CCSRBAR is
moved from 0xE0000000 to 0xA0000000).

If you want to boot Linux with CONFIG_TQM_BIGFLASH set, the new
memory map also has to be considered in the kernel (changed
CCSRBAR address, changed PCI IO base address, ...). Please use
an appropriate Flat Device Tree blob (tqm8548.dtb).

Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-11 00:05:14 -05:00
Wolfgang Grandegger
1c2deff22c TQM85xx: NAND support via local bus UPMB
This patch adds support for NAND FLASH on the TQM8548. It is disabled by
default and can be enabled for the TQM8548 modules. It is now based on
the re-written FSL NAND UPM driver. A patch has been posted earlier today
with the subject:

"NAND FSL UPM: driver re-write using the hwcontrol callback"

Note that the R/B pin is not supported by that module requiring to use
the specified maximum delay time.

Note: With NAND support enabled the size of the U-Boot image exceeds
256 KB and TEXT_BASE must therefore be set to 0xfff80000 in config.mk,
doubling the image size :-(.

Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-11 00:05:08 -05:00
Wolfgang Grandegger
b9e8078bb3 TQM8548: PCI express support
This patch adds support for PCI express cards. The board support
now uses common FSL PCI init code, for both, PCI and PCIe on all
TQM85xx modules.

Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-11 00:05:01 -05:00
Wolfgang Grandegger
1287e0c55a TQM8548: Basic support for the TQM8548 modules
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4

Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.

Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-11 00:01:43 -05:00
Wolfgang Grandegger
2599135320 TQM85xx: Support for Flat Device Tree
This patch adds support for Linux kernels using the Flat Device Tree.
It also re-defines the default environment settings for booting Linux
with the FDT blob.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-11 00:00:45 -05:00
Wolfgang Grandegger
d9ee843d54 TQM85xx: Support for Intel 82527 compatible CAN controller
This patch adds initialization of the UPMC RAM to support up to two
Intel 82527 compatible CAN controller on the TQM85xx modules.

Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-10 23:59:44 -05:00
Wolfgang Grandegger
518d5cfe72 TQM85xx: Bugfix in the SDRAM initialisation
The CS0_BNDS register is now set according to the detected
memory size.

Signed-off-by Martin Krause <martin.krause@tqs.de>
2008-06-10 23:58:58 -05:00
Wolfgang Grandegger
45dee2e620 TQM85xx: Fix chip select configuration for second FLASH bank
This patch fixes the re-calculation of the automatic chip select
configuration for boards with two populated FLASH banks.

Signed-off-by: Martin Krause <martin.krause@tqs.de>
2008-06-10 23:58:26 -05:00
Wolfgang Grandegger
5d5bd838f7 TQM85xx: Fix CPM port pin configuration
Do not configure port pins PD30/PD31 as SCC1 TxD/RxD except for the TQM8560
board. On the other TQM85xx boards (TQM8541 and TQM8555) SCC1 is not used
as serial interface anyway. Worse, on some board variants configuring the
pins for SCC1 leads to short circuits (for example on the TQM8541-BG).

Signed-off-by: Martin Krause <martin.krause@tqs.de>
2008-06-10 23:53:03 -05:00
Wolfgang Grandegger
b99ba1679e TQM85xx: Various coding style fixes
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-10 23:52:56 -05:00
Wolfgang Grandegger
4677988c7e TQM: move TQM boards to board/tqc
Move all TQM board directories to the vendor specific directory "tqc"
for modules from TQ-Components GmbH (http://www.tqc.de).

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-10 18:22:26 -05:00