Adds a class for MDIO MUXes, which control access to a series of
downstream child MDIOs.
MDIO MUX drivers are required to implement a select function used to switch
between child buses.
MUX children are registered as MDIO buses and they can be used just like
regular MDIOs.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Convert CONFIG_TFTP_BLOCKSIZE to Kconfig, update defconfigs,
headers and whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Convert CONFIG_IP_DEFRAG to Kconfig, update defconfigs, headers
and whitelist. This patch is a follow-up on a patch by Christian
Gmeiner with the added config/header/whitelist updates.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add the standard Ethernet device tree bindings (imported from v5.0 of
the Linux kernel) and implement support for reading the MAC address for
Ethernet devices in the Ethernet uclass. If the "mac-address" property
exists, the MAC address will be parsed from that. If that property does
not exist, the "local-mac-address" property will be tried as fallback.
MAC addresses from device tree take precedence over the ones stored in
a network interface card's ROM.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order for the device to use the proper MAC address, which can have
been configured in the environment prior to the device being registered,
ensure that the MAC address is written after the device has been probed.
For devices that are registered before the network stack is initialized,
this is already done during eth_initialize(). If the Ethernet device is
on a bus that is not initialized on early boot, such as PCI, the device
is not available at the time eth_initialize() is called, so we need the
MAC address programming to also happen after probe.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This fixes the automatic lmb initialization and reservation for boards
with more than one DRAM bank.
This fixes the CVE-2018-18439 and -18440 fixes that only allowed to load
files into the firs DRAM bank from fs and via tftp.
Found-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As a follow-up, change the name of the newly introduced function
'lmb_get_unreserved_size' to 'lmb_get_free_size', which is more
appropriate.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fix test/lib/lmb.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ether_crc was added to the core net code in commit 53a5c424bf
("multicast tftp: RFC2090") so that other drivers could use it. However
the only current user of it is tsec.c so move it there.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When dealing with two ethernet ports and having "netretry" set
to "once", it could occur that the connection (e.g. an ARP
request) failed, hence the status of the netloop was
"NETLOOP_FAIL". Due to the setting of "netretry", the network
logic would then switch to the other network interface,
assigning "ret" with the return value of "net_start_again()".
If this call succeeded we would return 0 (i.e. success) to
the caller when in reality the network action failed.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes CVE-2018-18439 ("insufficient boundary checks in network
image boot") by using lmb to check for a valid range to store
received blocks.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Always build lib/lmb.o on LMB and lib/fdtdec.o on OF_LIBFDT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Make it possible to add TCP versions of the same, while reusing
IP portions. This patch should not change any behavior.
Signed-off-by: Duncan Hare <DH@Synoia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Peter originally sent a fix, but it breaks a number of other things.
This addresses the original reported issue in a different way.
That report was:
> U-Boot has 1 common buffer to send Ethernet frames, pointed to by
> net_tx_packet. When sending to an IP address without knowing the MAC
> address, U-Boot makes an ARP request (using the arp_tx_packet buffer)
> to find out the MAC address of the IP addressr. When a matching ARP
> reply is received, U-Boot continues sending the frame stored in the
> net_tx_packet buffer.
>
> However, in the mean time, if U-Boot needs to send out any network
> packets (e.g. replying ping packets or ARP requests for its own IP
> address etc.), it will use the net_tx_packet buffer to prepare the
> new packet. Thus this buffer is no longer the original packet meant
> to be transmitted after the ARP reply. The original packet will be
> lost.
This instead uses the ARP tx buffer to send async replies in the case
where we are actively waiting for an ARP reply.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Tran Tien Dat <peter.trantiendat@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This single-sources the state of the ARP.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When a USB ethernet device is halted, the device driver is removed. When
this happens the uclass private memory is freed and uclass_priv is set to
NULL. This causes a data abort when uclass_priv->state is then set to
ETH_STATE_PASSIVE.
Fix it by checking if uclass_priv is NULL before setting uclass_priv->state
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The same basic parsing was implemented in tftp and nfs, so add a helper
function to do the work once.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Instead of depending on a env callback for bootfile, read it explicitly.
We do this because the bootfile can be specified on the command line and
if it is, we will overwrite the internal variable. If a netboot_common()
is called again with no bootfile parameter, we want to use the one in
the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
With net autoload, we check the prerequisites for the initial command,
but the greater prerequisites when autoloading are not checked.
If we would attempt to autoload, check those prerequisites too.
If we are not expecting a serverip from the server, then don't worry
about it not being set, but don't attempt to load if it isn't.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
For net_boot_common, we allow the serverip to be specified as part of
the boot file name. For net commands that require serverip, include that
source as a valid specification of serverip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
nfs was only printing basic info about the transfer in the case of a
DEBUG build. Print the same level of detail as tftp always.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The check for sending to the gateway was not using the correct variable
for comparison, so it was reporting that packets are sent to the gateway
when they were not.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
With driver model, we were not checking if the state of the device was
marked as active before calling the halt function. Check that the device
is probed and also marked as active. This avoids the case where we were
calling halt on the first device in net_init() and the driver would
operate on bogus data structures causing problems. In this case, the
priv was all 0, so halt() would close STDIN.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently we can choose between 2 different types of behavior for the
serverip variable:
1) Always overwrite it with the DHCP server IP address (default)
2) Ignore what the DHCP server says (CONFIG_BOOTP_SERVERIP)
This patch adds a 3rd option:
3) Use serverip from DHCP if no serverip is given
(CONFIG_BOOTP_PREFER_SERVERIP)
With this new option, we can have the default case that a boot file gets
loaded from the DHCP provided TFTP server work while allowing users to
specify their own serverip variable to explicitly use a different tftp
server.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We can call commands like dhcp and bootp without arguments or with
explicit command line arguments that really should tell the code where
to look for files instead.
Unfortunately, the current code simply overwrites command line arguments
in the dhcp case with dhcp values.
This patch allows the code to preserve the command line values if they
were set on the command line. That way the semantics are slightly more
intuitive.
The reason this patch does that by introducing a new variable is that we
can not rely on net_boot_file_name[0] being unset, as today it's
completely legal to call "dhcp" and afterwards run "tftp" and expect the
latter to repeat the same query as before. I would prefer not to break
that behavior in case anyone relies on it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new command 'wol': Wait for an incoming Wake-on-LAN packet or
time out if no WoL packed is received.
If the WoL packet contains a password, it is saved in the environment
variable 'wolpassword' using the etherwake format (dot or colon
separated decimals).
Intended use case: a networked device should boot an alternate image.
It's attached to a network on a client site, modifying the DHCP server
configuration or setup of a tftp server is not allowed.
After power on the device waits a few seconds for a WoL packet. If a
packet is received, the device boots the alternate image. Otherwise
it boots the default image.
This method is a simple way to interact with a system via network even
if only the MAC address is known. Tools to send WoL packets are
available on all common platforms.
Some Ethernet drivers seem to pad the incoming packet. The additional
padding bytes might be recognized as Wake-on-LAN password bytes.
By default enabled in pengwyn_defconfig.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When building without FASTBOOT_FLASH we don't include the intermediate
update callback to keep the client alive, so ensure we don't try setting
it here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
That can happen if duplicate UDP packet arrived, and that's not uncommon.
Anyway, we ignore packets with rpc_id lower than last we sent for other
requests, so it makes sense to do that for read request as well.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Global variable "net_state" is used in net_loop() state-machine.
But it happens that some times the net_loop() can be called
multiple times in the same call stack. For example when the
netconsole is enabled and we print the message while some other
net protocol is in action. Netconsole will overwrite the "net_state"
and that will break the logic for earlier started protocol.
To protect the state save and restore "net_state" variable each
time when we enter and exit net_loop().
Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On devices that have their first network interface provided by a FPGA,
the initialization of further interfaces will fail if the FPGA is not
yet programmed. This leads to problems during factory setup when the
data is supposed to be loaded over secondary netowork interfaces.
To avoid this, use the uclass_{first,next}_device_check functions to
initialize as many ethernet devices as possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When the following configuration is set
# CONFIG_CMD_DHCP is not set
CONFIG_CMD_BOOTP=y
CONFIG_BOOTP_NTPSERVER=y
The following compile error is observed
error: used struct type value where scalar is required
if (net_ntp_server)
^~~~~~~~~~~~~~
Resolve this by checking net_ntp_server.s_addr instead.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Options that controlled the tftp and bootp commands depended on their
commands, but lived in the net menu.
Move them so they are in a consistent location.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Previously, CMD_NET was an alias for 2 commands (bootp and tftpboot) and
they we not able to be disabled. Separate out those 2 commands and move
CMD_NET up to the menu level, which more accurately represents the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
In the efi_loader main loop we call eth_rx() occasionally. This rx function
might end up calling into devices that haven't been initialized yet,
potentially resulting in a lot of transfer timeouts.
Instead, let's make sure the ethernet device is actually initialized before
reading from or writing to it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The "net_try_count" counter starts from "1".
And the "retrycnt" contains requested amount of retries.
With current logic, that means that the actual retry amount
will be one time less then what we set in "netretry" env.
For example setting "netretry" to "once" will make "retrycnt"
equal "1", so no retries will be triggered at all.
Fix the logic by changing the statement of "if" condition.
Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
config_fallbacks.h had some logic to automatically select
LIB_RAND if RANDOM_UUID or CMD_UUID were set if LIB_HW_RAND wasn't
already selected. By migrating LIB_HW_RAND to Kconfig, we can
remove this check from config_fallbacks.h and put it into Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
[trini: Turn into a choice, add NET_RANDOM_ETHADDR]
Signed-off-by: Tom Rini <trini@konsulko.com>
This change allows the "MAY_FAIL" DHCP option to still attempt to
contact a DHCP server on each adapter and only give up once each
adapter has failed once. To get the existing behavior, set the
already-existing ethrotate=no variable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
In the general case, CONFIG_NFS_READ_SIZE is unchanged from the default
of 1024. There are in fact no in-tree users that increase this size.
Adjust the comment to reflect what could be done in the future in
conjunction with CONFIG_IP_DEFRAG.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:
getenv_vlan()
getenv_bootm_size()
getenv_bootm_low()
getenv_bootm_mapsize()
env_get_default()
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
For strncpy() select a minimal string length of destination and source
strings, here DEFAULT_NAME_LEN is preferable to MAX_LEN.
Due to the NUL-terminated contents of default_string the change is
a noop, however it removes a compilation warning if SH2/3/4 platform
specific strncpy() function is used:
In file included from include/linux/string.h:21:0,
from include/common.h:28,
from net/tftp.c:9:
net/tftp.c: In function 'tftp_start':
arch/sh/include/asm/string.h:52:42: warning: array subscript is above array bounds [-Warray-bounds]
: "0" (__dest), "1" (__src), "r" (__src+__n)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Previously seeded by obtaining mac addr from env. If mac addr was
never set, rand would output 0. This fix obtains the mac addr
from driver instead.
Signed-off-by: Jimmy Du <jimmy.du@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Checking if dev is NULL after dereferencing it does not make sense.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We will see warnings such as:
net/eth_common.c:57:61: warning: data argument not used by format string [-Wformat-extra-args]
sprintf(enetvar, index ? "%s%daddr" : "%saddr", base_name, index);
~~~~~~~~ ^
With clang. In this case we do not want to re-write our code to be less
compact as the above is intentional and readable. Add a comment above
the disabling so that it's clear why we want that warning off.
Signed-off-by: Tom Rini <trini@konsulko.com>
The network mask must be stored in network order when in a
'struct in_addr'.
This fix removes the "gatewayip needed but not set" message on the
console when using a link-local IP setup.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the ethernet address environment is set with a valid
ethernet address prevent overriding it as it is most likely
set by the user and he/she doesn't want board code to
automatically override it whatsoever.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, we print that the MAC from the SROM does not match. It can be
many forms of ROM, so lets drop the S.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In u-boot printf has been extended with the %pM formatter to allow
printing of MAC addresses. However buffers that want to store a MAC
address cannot safely get the size. Add a define for this case so the
string of a MAC address can be reliably obtained.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 674bb24982 ("net: cosmetic: Replace magic numbers in arp.c with
constants") introduced a nice define to replace the magic value 6 for
the ethernet hardware address. Replace more hardcoded instances of 6
which really reference the ARP_HLEN (iow the MAC/Hardware/Ethernet
address).
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
If mac-address is changed using "setenv ethaddr ...." command the new
mac-adress also must be written into the responsible ethernet driver.
This fixes the legacy ethernet handling.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Use random ethernet address if the ethernet address found
is invalid, not zero and config for random address
is defined.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If mac-address is changed using "setenv ethaddr ...." command the new
mac-adress also must be written into the responsible ethernet driver.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are a lot of SPL options in U-Boot to enable various features and
drivers. Currently these do not use Kconfig. Add them to Kconfig along
with suitable help, and drop them from the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit 6279b49e6c.
This caused a bad data crc.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Guillaume GARDET <guillaume.gardet@free.fr>
This reverts commit 998372b479.
This caused a data abort on some platform.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Guillaume GARDET <guillaume.gardet@free.fr>
We use an empty hostname, so remove all the "processing" of the
known-to-be-empty hostname and just write 0's where needed.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Instead of always allocating a huge temporary buffer on the stack and
then memcpy()ing the result into the transmit buffer, simply figure out
where in the transmit buffer the bytes will belong and write them there
directly as each message is built.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Much of the information is verbose and derived directly from the
environment. Only output in debug mode. This also saves about 300 bytes
from the code size.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Instead of repeating the same large snippet for dealing with attributes
it should be shared with a helper function.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The type of the buffer is uint32_t, but the parameter used to size it
is referring to bytes. Divide by the size of the array elements.
Strictly speaking, this shouldn't be needed at all... It could just be 1
just like the request.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The v3 handles can be larger than v2, but that doesn't mean we need a
separate buffer. Reuse the same (larger) buffer for both.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables NFSv3 support.
If NFSv2 is available use it as usual.
If NFSv2 is not available, but NFSv3 is available, use NFSv3.
If NFSv2 and NFSv3 are not available, print an error message since NFSv4 is not supported.
Tested on iMX6 sabrelite with 4 Linux NFS servers:
* NFSv2 + NFSv3 + NFSv4 server: use NFSv2 protocol
* NFSv2 + NFSv3 server: use NFSv2 protocol
* NFSv3 + NFSv4 server: use NFSv3 protocol
* NFSv3 server: use NFSv3 protocol
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Cc: joe.hershberger@ni.com
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is no reason to store the default filename in a separate buffer
only to immediately copy it to the main name buffer. Just write it there
directly and remove the other buffer.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
At least on bfin, this "specimen" is actually allocated in the BSS and
wastes lots of memory in already tight memory conditions.
Also, with the introduction of NFSv3 support, this waste got
substantially larger.
Just remove it. If a board needs a specific different defragment size,
that board can override this setting.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes incorrect RPC packet layout caused by
'long' type size difference on 64 and 32-bit architectures.
Signed-off-by: Ralf Hubert <r.hubert@technisat.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Avoid generating this section if there is nothing in it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The client architecture that we pass to a dhcp server depends on the target
payload that we want to execute. An EFI binary has a different client arch
than a legacy binary or a u-boot binary.
So let's parameterize the pxe client arch field to allow an override via
the distro script, so that our efi boot path can tell the dhcp server that
it's actually an efi firmware.
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we can expose network functionality to EFI applications,
the logical next step is to load them via pxe to execute them as
well.
This patch adds the necessary bits to the distro script to automatically
load and execute EFI payloads. It identifies the dhcp client as a uEFI
capable PXE client, hoping the server returns a tftp path to a workable
EFI binary that we can then execute.
To enable boards that don't come with a working device tree preloaded,
this patch also adds support to load a device tree from the /dtb directory
on the remote tftp server.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are client identifiers specifically reserved for ARM U-Boot
according to http://www.ietf.org/assignments/dhcpv6-parameters/dhcpv6-parameters.xml#processor-architecture.
So let's actually make use of them rather than the bogus 0x100 that
we emitted so far.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop the Xilinx define to 0x100 as it's not the correct value to
use].
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a bunch of boards that define their vendor class identifier and
client archs in the board files or in the distro config. Move everything
to the generic Kconfig options.
We're missing the distinction between i386 and x86_64, as I couldn't find
any config variable that would tell us the difference. Is that really important
to people? I guess not, so I left it out.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Both the dhcp as well as the bootp case add vendor class identifier
parameters into their packets. Let's move that into a separate function
to make overlaying easier.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
We can now successfully boot EFI applications from disk, but users
may want to also run them from a PXE setup.
This patch implements rudimentary network support, allowing a payload
to send and receive network packets.
With this patch, I was able to successfully run grub2 with network
access inside of QEMU's -M xlnx-ep108.
Signed-off-by: Alexander Graf <agraf@suse.de>
In rare circumstances two dhcp clients may generate the same
bootp ID. If this happens it is vital that the client also checks
the hw address in the received response to prevent IP address conflicts.
Signed-off-by: Anton Persson <don.juanton@gmail.com>
There is currently one config option (CONFIG_NET_RETRY_COUNT) that
is available to tune the retries of the network stack.
Unfortunately, it is global to all protocols, and the value is
interpreted differently in all of them.
Add a new environment variable that directly sets the retry period for
BOOTP timeouts. If this new value is not set, the period is still derived
from the default number of retries, or from CONFIG_NET_RETRY_COUNT if
defined. When both the new variable is set and CONFIG_NET_RETRY_COUNT
is defined, the variable has precedence.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
This fixes the following error when building microblaze-generic:
net/eth-uclass.c: In function 'eth_post_probe':
net/eth-uclass.c:466:18: error: 'gd' undeclared (first use in this function)
ops->start += gd->reloc_off;
Fixes: db9391e1 ("net: Move driver-model code into its own file")
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the bootfile name in the DHCP Request packet, in addition
to it already being sent in the DHCP Discover.
This is needed by some DHCP servers so that the bootfile name is
properly returned by the server to the client in the DHCP Ack, as
expected by U-Boot.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Rename this file to make it clear it is for the old networking drivers
and not for use with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Every other uclass is in its own file. Create a new eth-uclass.c file and
move the driver-model code into it, so that networking is consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move eth_current_changed(), eth_set_current(), eth_mac_skip() and
eth_get_name() into the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the functions which set ethernet environment variables to the common
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Only half of the init is actually common. Move that part into a new common
file and call it from driver-model and legacy code. More common functions
will be added in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We should avoid weak functions with driver model. Existing boards that use
driver model don't need them, so let's kill them off.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When doing `dhcp`, there is a bad dhcp server in my network
which always reply dhcp request with yiaddr 0, which cause
uboot can not successfully get ipaddr from the good dhcp server.
But the Linux PC can get the ip address even if there is a bad
dhcp server. This patch is to fix that even if there is a bad
dhcp server, uboot can still get ipaddr and tftp work ok.
The way is to ignore the packets from the bad dhcp server by filtering
out the yiaddr whose value is 0.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In many parts of the computing world having a unique MAC address
sitting in some on-NIC storage is considered the normal case.
Remove the warning to not scare the user unnecessarily.
This applies to Highbank/Midway and ARM's Juno, for instance.
Besides that this fixes the formatting on Midway, for instance,
which currently looks like:
...
Net: xgmac0
Warning: xgmac0 using MAC address from net device
, xgmac1
Warning: xgmac1 using MAC address from net device
...
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Introduced in 45b4773 (net/arp: account for ARP delay, avoid duplicate packets on timeout)
Check the arp timeout and adjust the timeout start time before the call
to eth_recv() so that the sandbox driver has the opportunity to adjust
the sandbox timer after the new start time has been recorded.
Also, change the adjustment amount by 11 seconds instead of exactly the
10 seconds that the ping timout is expecting since the timeout check is
looking for the time elapsed to be greater than but not equal to the
specified delay.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Simon Glass <sjg@chromium.org>
When 'ethrotate' variable is set to 'no' and 'ethact' variable
is already set to an ethernet device, we should stick to 'ethact'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
In eth_current_changed(), the call to eth_get_dev() below has a side
effect of rotating ethernet device if uc_priv->current == NULL. This
is not what we want when 'ethrotate' variable is 'no'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
All ethernet operation needs to be updated for architectures which
requires MANUAL_RELOC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
eth_get_dev() can return NULL which means device_probe() fails for
that ethernet device. Add return value check in various places or
U-Boot will crash due to NULL pointer access.
With this commit, 'dm_test_eth_act' test case passes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
platdata->enetaddr was assigned to a value in dev_probe() last time.
If we don't clear it, for dev_probe() at the second time, dm eth
will end up treating it as a MAC address from ROM no matter where it
came from originally (maybe env, ROM, or even random). Fix this by
clearing platdata->enetaddr when removing an Ethernet device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The net_boot_file_name buffer is used as storage for the bootfilename
command line argument to network boot commands such as tftp and nfs.
Increase the size of this buffer to 1024 bytes as the current size of
128 bytes is restrictive for arbitrary paths on the server.
Signed-off-by: Jacob Stiffler <j-stiffler@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If Option 52 in the vendor option field signals overloading
of the file and/or sname fields, these field may contain
additional options. Formatting of file/sname contained options
is the same as in the vendor options field, but without the
leading magic.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If 'file' is overloaded, it is wrong to get or put the bootfile name
from it/to it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As we don't modify the 'name' parameter, so change it to const.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The loop should check all ethenet devices, not only the first device,
to set each specified ethaddr, or it'll cause failure when we use other
devices.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Timeout handler should be stopped after reception of DHCPACK. If "autoload"
is not set, the handler is immediately replaced by the TFTP handler,
otherwise it may trigger before the next boot stage begins.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
eth_rx() in the main reception loop may trigger sending a packet which
is already timed out (or will immediately) upon reception of an ARP reply.
As long as the ARP reply is pending, the timeout handler of a packet
should be postponed.
Happens on TFTP with bad network (e.g. WLAN).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net_start_again() will be called from net_loop() if state is NETLOOP_FAIL.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pad has no len byte, so the normal parsing code fails.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
RFC1542, 3.2:
"The 'secs' field of a BOOTREQUEST message SHOULD represent the
elapsed time, in seconds, since the client sent its first BOOTREQUEST
message. Note that this implies that the 'secs' field of the first
BOOTREQUEST message SHOULD be set to zero."
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename check_packet to check_reply_packet to make its function more
obvious.
The check for DHCP_* values is completely off, as it should
compare against DHCP option 53 (Message Type). Only valid value for
any Bootp/DHCP reply is BOOTREPLY.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes the error when STATUS_LED_BOOT is not defined.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If CONFIG_CMD_DHCP is enabled, the vci (vendor-class-identifier) string
isn't inserted into the bootp-packet during SPL stage because the
CONFIG_BOOTP_VCI_STRING
instead
CONFIG_SPL_NET_VCI_STRING
We fix this with testing for CONFIG_SPL_BUILD and testing for existing
CONFIG_SPL_NET_VCI_STRING.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TFTP source and destination port variable names are
'tftpsrcp' and 'tftpdstp' in the code, but 'tftpsrcport'
and 'tftpdstport' in the README file. Fix the README.
Add environment variable 'tftptimeoutcountmax'. As per the
comments about the global variable tftp_timeout_count_max,
make sure tftptimeoutcountmax is nonnegative.
Introduce configuration option CONFIG_NET_TFTP_VARS,
which controls whether environment variables tftpblocksize,
tftptimeout, and tftptimoueoutcountmax are read by the TFTP
client code. CONFIG_NET_TFTP_VARS defaults to y but can be
set to n by targets with to tight size contraints.
Make bf527-ezkit set CONFIG_NET_TFTP_VARS to n to keep the
target size below limit.
This patch introduces CONFIG_NETCONSOLE as an option to the
Kconfig system.
Joe Hershberger pointed out that it may not be entirely free of
problems, as many boards predating the driver model define this
symbol directly via include files. In case they're not properly
migrated, their NetConsole might 'vanish' if they start to use
CONFIG_NET or CONFIG_NETDEVICES.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The previous eth_device struct returned by eth_get_dev() allowed
code to directly query the state member field. However, with
CONFIG_DM_ETH this data gets encapsulated (i.e. private), and
eth_get_dev() returns a udevice struct 'abstraction' instead.
This breaks legacy code relying on the former behaviour - e.g.
netconsole.
(see http://lists.denx.de/pipermail/u-boot/2015-June/216528.html)
The patch introduces a method to retrieve the ethernet device
state in a 'clean' and uniform way, supporting both legacy code
and driver model. The new function eth_is_active() accepts a
device struct pointer and tests it for ETH_STATE_ACTIVE.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When given a device name string, we should test to see if it is
really an alias like "eth#".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With driver model, board_eth_init() or cpu_eth_init() is not a must.
Thus we don't need print a misleading "Net Initialization Skipped".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 620776d "tftp: adjust settings to be suitable for 100Mbit ethernet"
causes the following error message when trying to load a file using 'tftp'
command via a tftp server.
TFTP error: 'Unsupported option(s) requested' (8)
This is due to with commit 620776d changes, the tftp option 'timeout'
value is now set to zero which is an invalid value as per RFC2349 [1].
Valid values range between "1" and "255" seconds, inclusive. With some
tftp servers that strictly implement the RFC requirement, it reports
such an error message.
Revert commit 620776d for RFC compliance.
[1] https://www.ietf.org/rfc/rfc2349.txt
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This change gives the ability to reuse the <tftp.h> header file by other
subsystems (like e.g. dfu).
Without this change compilation error emerges for the legacy update.c file.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current behavior is that if CTRL+C is pressed command returns 0 that was
successful which is not correct behavior.
The easiest test case is "tftpboot 80000 uImage && echo yes"
and press CTRL+C. Then the second command is called which is incorrect.
Error log:
zynq-uboot> tftpb 80000 uImage && echo yes
Gem.e000b000:7 is connected to Gem.e000b000. Reconnecting to
Gem.e000b000
Gem.e000b000 Waiting for PHY auto negotiation to complete....... done
Using Gem.e000b000 device
TFTP from server 192.168.0.102; our IP address is 192.168.0.101
Filename 'uImage'.
Load address: 0x80000
Loading: ################
Abort
yes
zynq-uboot>
This patch adds -EINTR return value when CTRL+C is pressed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust timouts and retry counts to be suitable for loaded ethernet
network. With 5 seconds timeout, 10 retries maximum, tftp is
impossible even on local network with single full-speed TCP
connection.
100msec timeout should be suitable for most networks tftp is used on,
that is local ethernets. Timeout count really needs to be way higher,
as lost packets are normal when TCP is running over the same network.
Enforce 10msec minimum.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CONFIG_TFTP_TSIZE should limit a tftp downloads progress to 50 '#'
chars. Make this work also for small files.
If the file size is small, i.e. smaller than 2 tftp block sizes the
number of '#' can get much larger. i.e. with a 1 byte file 65000
characters are printed, with a 512 byte file around 500.
When using CONFIG TFTP BLOCKSIZE together with CONFIG_IP_DEFRAG the
issue is more notable.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some drivers may want to implement this method for some of their devices but
not for others. So it is not possible to just leave the operation out of
the table. Drivers could get around this by masquerading as two separate
drivers but that seems unpleasant.
Allow the driver to return an error when it does not want to process the
write_hwaddr() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices can take a long time to work out whether they have a new packet
or now. For example the ASIX USB Ethernet dongle can take 5 seconds to do
this, since it waits until it gets a new packet on the wire before allowing
the USB bulk read packet to be submitted.
At present with driver mode the Ethernet receive code reads 32 packets. This
can take a very long time if we must wait for all 32 packets. The old code
(before driver model) worked by reading a single set of packets from the USB
device, then processing all the packets with in. It would be nice to use
the same behaviour with driver model.
Add a flag to the receive method which indicates that the driver should try
to find a packet if available, by consulting the hardware. When the flag is
not set, it should just return any packet data it has already received. If
there is none, it should return -EAGAIN so that the loop will terminate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of selecting REGEX when NET is enabled, make it the default, but
allow boards that are tiny to disable it and lose functionality on all
but the first Ethernet adapter.
cm-bf548, bf538f-ezkit, and bf533-stamp need this. None appear to have
more than one Ethernet interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
NET_RANDOM_ETHADDR depends on lib/rand.c. This patch adds dependency to
Kconfig to ensure that library is also compiled.
Remove the definitions from Blackfin boards' include/configs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When the ethaddr is changed in the env, update the device pdata at the
same time (only if it is probed for the DM case; only if registered for
the non-DM case). Again this gets us closer to completely non-polled
env needed to simplify the net_loop.
This requires that the NET feature select the REGEX feature.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The bootfile env var is already kept up to date by the callback in net.c
so there is no need to poll it too.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean