Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.
For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit d5d726d3cc ("configs: stm32mp1: only support SD card after
NOR in bootcmd_stm32mp"), the stm32mp1 boards only support SD card after
NOR boot device, so the MTD partitions for nand0 or spi-nand0 are useless
(no need of "UBI" partition in nand0 or spi-nand0).
This patch removes these nand MTD update for nor boot and simplify nand0
and spi-nand0 support (remove the mtd_boot variable).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use CONFIG_IS_ENABLED to prevent ifdef in set_dfu_alt_inf.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Migrate the ST Microelectronics STUSB160X Type-C controller code in
a generic I2C driver in st/common, based on Linux one in :
drivers/usb/typec/stusb160x.c
This patch simplifies the stm32mp1 board code and allows to reuse
this STUSB160X driver in other boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
With TEE 3.7.0, the partition teed (OP-TEE pageable
code and data) need to increase up to 512KB in NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1
and need to be updated for 800MHz support and only after the clock
tree initialization.
The VDDCORE voltage value is provided by clock driver, saved in global
variable opp_voltage_mv and udpated in SPL board_early_init_f(),
just after clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move function board_ddr_power_init() in a new file stpmic1 in
board/st/common to avoid duplicated code in each board using
stpmic1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog
command detects in the parsed flash layout files:
- a fsbl partition in NOR.
- a tee partition in NOR/NAND/SPI-NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NAND and SPI-NAND when boot from
NOR or NAND/SPI-NAND is detected.
This patch avoids to define the save MTD partition name for NOR and NAND
devices and issue with latest kernel: only the needed MTD partitions
are defined.
For boot from NOR
1/ bootloader (TF-A, U-Boot and OP-TE) in NOR
2/ one large UBI partition in NAND
For boot from NAND
1/ bootloader (TF-A, U-Boot and OP-TE) in MTD raw partition
2/ one large UBI partition
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code set_dfu_alt_info() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code board_get_mtdparts() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the command stboard to support the updated coding of OTP 59 with
finished good.
The ST product codification have several element
- "Commercial Product Name" (CPN): type of product board (DKX, EVX)
associated to the board ID "MBxxxx"
- "Finished Good" or "Finish Good" (FG):
effective content of the product without chip STM32MP1 (LCD, Wifi, …)
- BOM: cost variant for same FG
(for example, several provider of the same component)
For example
- commercial product = STM32MP157C-EV1
- Finished Good = EVA32MP157A1$AU1
Booth information are written on board and these information is also saved
in OTP59:
bit [31:16] (hex) => Board id, MBxxxx
bit [15:12] (dec) => Variant CPN (1....15)
bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
bit [7:4] (dec) => Variant FG : finished good (NEW)
bit [3:0] (dec) => BOM (01, .... 255)
The updated command is:
stboard [-y] <Board> <VarCPN> <Revision> <VarFG> <BOM>
And the displayed STMicroelectronics board identification is:
Board: MB<Board> Var<VarCPN>.<VarFG> Rev.<Revision>-<BOM>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Lock the OTP used for board identification for the ST boards after
programming.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Read the value directly from the OTP and no more of the shadows
to avoid the need of reboot after stboard command to have correct value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update management of misc_write, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the ST command in board/st/common, as this command is only used
by ST board. Prepare the support in U-Boot of boards with STM32MP15x
SOC but not STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
