powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7

These boards have been orphaned for more than 6 months.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit is contained in:
Masahiro Yamada 2014-09-29 01:38:00 +09:00 committed by Tom Rini
parent 9ed3246e19
commit e7a565638a
27 changed files with 2 additions and 2495 deletions

View File

@ -64,12 +64,6 @@ config TARGET_SUVD3
config TARGET_TUXX1
bool "Support tuxx1"
config TARGET_MERGERBOX
bool "Support MERGERBOX"
config TARGET_MVBLM7
bool "Support MVBLM7"
config TARGET_TQM834X
bool "Support TQM834x"
@ -89,8 +83,6 @@ source "board/freescale/mpc837xemds/Kconfig"
source "board/freescale/mpc837xerdb/Kconfig"
source "board/ids/ids8313/Kconfig"
source "board/keymile/km83xx/Kconfig"
source "board/matrix_vision/mergerbox/Kconfig"
source "board/matrix_vision/mvblm7/Kconfig"
source "board/mpc8308_p1m/Kconfig"
source "board/sbc8349/Kconfig"
source "board/tqc/tqm834x/Kconfig"

View File

@ -1,12 +0,0 @@
if TARGET_MERGERBOX
config SYS_BOARD
default "mergerbox"
config SYS_VENDOR
default "matrix_vision"
config SYS_CONFIG_NAME
default "MERGERBOX"
endif

View File

@ -1,6 +0,0 @@
MERGERBOX BOARD
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mergerbox/
F: include/configs/MERGERBOX.h
F: configs/MERGERBOX_defconfig

View File

@ -1,8 +0,0 @@
#
# (C) Copyright 2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# SPDX-License-Identifier: GPL-2.0+
#
obj-y += mergerbox.o pci.o fpga.o sm107.o

View File

@ -1,59 +0,0 @@
Matrix Vision MergerBox
-----------------------
1. Board Description
The MergerBox is a 120x160mm single board computing platform
for 3D Full-HD digital video processing.
Power Supply is 10-32VDC.
2 System Components
2.1 CPU
Freescale MPC8377 CPU running at 800MHz core and 333MHz csb.
256 MByte DDR-II memory @ 333MHz data rate.
64 MByte Nor Flash on local bus.
1 GByte Nand Flash on FCM.
1 Vitesse VSC8601 RGMII ethernet Phys.
1 USB host controller over ULPI I/F with 4-Port hub.
2 serial ports. Console running on ttyS0 @ 115200 8N1.
1 mPCIe expansion slot (PCIe x1 + USB) used for Wifi/Bt.
2 PCIe x1 busses on local mPCIe and cutom expansion connector.
2 SATA host ports.
System configuration (HRCW) is taken from I2C EEPROM.
2.2 Graphics
SM107 emebedded video controller driving a 5" 800x480 TFT panel.
Connected over 32-Bit/66MHz PCI utilizing 4 MByte embedded memory.
2.3 FPGA
Altera Cyclone-IV EP4C115 with several PCI DMA engines.
Connects to 7x Gennum 3G-SDI transceivers as video interconnect
as well as a HDMI v1.4 compliant output for 3D monitoring.
Utilizes two more DDR-II controllers providing 256MB memory.
2.4 I2C
Bus1:
AD7418 @ 0x50 for voltage/temp. monitoring.
SX8650 @ 0x90 touch controller for HMI.
EEPROM @ 0xA0 for system setup (HRCW etc.) + vendor specifics.
Bus2:
mPCIe SMBus
SiI9022A @ 0x72/0xC0 HDMI transmitter.
TCA6416A @ 0x40 + 0x42 16-Bit I/O expander.
LMH1983 @ 0xCA video PLL.
DS1338C @ 0xD0 real-time clock with embedded crystal.
9FG104 @ 0xDC 4x 100MHz LVDS SerDes reference clock.
3 Flash layout.
reset vector is 0x00000100, i.e. low boot.
00000000 u-boot binary.
00100000 FPGA raw bit file.
00300000 FIT image holding kernel, dtb and rescue squashfs.
03d00000 u-boot environment.
03e00000 splash image
mtd partitions are propagated to linux kernel via device tree blob.

View File

@ -1,158 +0,0 @@
/*
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com.
*
* (C) Copyright 2011
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <ACEX1K.h>
#include <command.h>
#include "mergerbox.h"
#include "fpga.h"
Altera_CYC2_Passive_Serial_fns altera_fns = {
fpga_null_fn,
fpga_config_fn,
fpga_status_fn,
fpga_done_fn,
fpga_wr_fn,
fpga_null_fn,
fpga_null_fn,
};
Altera_desc cyclone2 = {
Altera_CYC2,
passive_serial,
Altera_EP2C20_SIZE,
(void *) &altera_fns,
NULL,
0
};
DECLARE_GLOBAL_DATA_PTR;
int mergerbox_init_fpga(void)
{
debug("Initialize FPGA interface\n");
fpga_init();
fpga_add(fpga_altera, &cyclone2);
return 1;
}
int fpga_null_fn(int cookie)
{
return 0;
}
int fpga_config_fn(int assert, int flush, int cookie)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
u32 dvo = gpio->dat;
dvo &= ~FPGA_CONFIG;
gpio->dat = dvo;
udelay(5);
dvo |= FPGA_CONFIG;
gpio->dat = dvo;
return assert;
}
int fpga_done_fn(int cookie)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
int result = 0;
udelay(10);
debug("CONF_DONE check ... ");
if (gpio->dat & FPGA_CONF_DONE) {
debug("high\n");
result = 1;
} else
debug("low\n");
return result;
}
int fpga_status_fn(int cookie)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
int result = 0;
debug("STATUS check ... ");
if (gpio->dat & FPGA_STATUS) {
debug("high\n");
result = 1;
} else
debug("low\n");
return result;
}
int fpga_clk_fn(int assert_clk, int flush, int cookie)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
u32 dvo = gpio->dat;
debug("CLOCK %s\n", assert_clk ? "high" : "low");
if (assert_clk)
dvo |= FPGA_CCLK;
else
dvo &= ~FPGA_CCLK;
if (flush)
gpio->dat = dvo;
return assert_clk;
}
static inline int _write_fpga(u8 val, int dump)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
int i;
u32 dvo = gpio->dat;
if (dump)
debug(" %02x -> ", val);
for (i = 0; i < 8; i++) {
dvo &= ~FPGA_CCLK;
gpio->dat = dvo;
dvo &= ~FPGA_DIN;
if (dump)
debug("%d ", val&1);
if (val & 1)
dvo |= FPGA_DIN;
gpio->dat = dvo;
dvo |= FPGA_CCLK;
gpio->dat = dvo;
val >>= 1;
}
if (dump)
debug("\n");
return 0;
}
int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie)
{
unsigned char *data = (unsigned char *) buf;
int i;
debug("fpga_wr: buf %p / size %d\n", buf, len);
for (i = 0; i < len; i++)
_write_fpga(data[i], 0);
debug("\n");
return FPGA_SUCCESS;
}

View File

@ -1,13 +0,0 @@
/*
* SPDX-License-Identifier: GPL-2.0+
*/
extern int mergerbox_init_fpga(void);
extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
extern int fpga_status_fn(int cookie);
extern int fpga_config_fn(int assert, int flush, int cookie);
extern int fpga_done_fn(int cookie);
extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
extern int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie);
extern int fpga_null_fn(int cookie);

View File

@ -1,235 +0,0 @@
/*
* Copyright (C) 2007 Freescale Semiconductor, Inc.
*
* Copyright (C) 2011 Matrix Vision GmbH
* Andre Schwarz <andre.schwarz@matrix-vision.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <hwconfig.h>
#include <i2c.h>
#include <spi.h>
#include <asm/io.h>
#include <asm/fsl_mpc83xx_serdes.h>
#include <fdt_support.h>
#include <spd_sdram.h>
#include "mergerbox.h"
#include "fpga.h"
#include "../common/mv_common.h"
static void setup_serdes(void)
{
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
}
#if defined(CONFIG_SYS_DRAM_TEST)
int testdram(void)
{
uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
uint *p;
printf("Testing DRAM from 0x%08x to 0x%08x\n",
CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END);
printf("DRAM test phase 1:\n");
for (p = pstart; p < pend; p++)
*p = 0xaaaaaaaa;
for (p = pstart; p < pend; p++) {
if (*p != 0xaaaaaaaa) {
printf("DRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
printf("DRAM test phase 2:\n");
for (p = pstart; p < pend; p++)
*p = 0x55555555;
for (p = pstart; p < pend; p++) {
if (*p != 0x55555555) {
printf("DRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
printf("DRAM test passed.\n");
return 0;
}
#endif
phys_size_t initdram(int board_type)
{
u32 msize;
volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
volatile clk83xx_t *clk = (clk83xx_t *)&immr->clk;
/* Enable PCI_CLK[0:1] */
clk->occr |= 0xc0000000;
udelay(2000);
#if defined(CONFIG_SPD_EEPROM)
msize = spd_sdram();
#else
immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
u32 msize_log2;
msize = CONFIG_SYS_DDR_SIZE;
msize_log2 = __ilog2(msize);
im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
udelay(50000);
im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
udelay(1000);
im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
udelay(1000);
im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
__asm__ __volatile__("sync");
udelay(1000);
im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
udelay(2000);
#endif
setup_serdes();
return msize << 20;
}
int checkboard(void)
{
puts("Board: Matrix Vision MergerBox\n");
return 0;
}
int misc_init_r(void)
{
u16 dim;
int result;
volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (gpio83xx_t *)&immr->gpio[1];
unsigned char mac[6], mac_verify[6];
char *s = getenv("reset_env");
for (dim = 10; dim < 180; dim += 5) {
mergerbox_tft_dim(dim);
udelay(100000);
}
if (s)
mv_reset_environment();
i2c_read(SPD_EEPROM_ADDRESS, 0x80, 2, mac, sizeof(mac));
/* check if Matrix Vision prefix present and export to env */
if (mac[0] == 0x00 && mac[1] == 0x0c && mac[2] == 0x8d) {
printf("valid MAC found in eeprom: %pM\n", mac);
eth_setenv_enetaddr("ethaddr", mac);
} else {
printf("no valid MAC found in eeprom.\n");
/* no: check the env */
if (!eth_getenv_enetaddr("ethaddr", mac)) {
printf("no valid MAC found in env either.\n");
/* TODO: ask for valid MAC */
} else {
printf("valid MAC found in env: %pM\n", mac);
printf("updating MAC in eeprom.\n");
do {
result = test_and_clear_bit(20, &gpio->dat);
if (result)
printf("unprotect EEPROM failed !\n");
udelay(20000);
} while(result);
i2c_write(SPD_EEPROM_ADDRESS, 0x80, 2, mac, 6);
udelay(20000);
do {
result = test_and_set_bit(20, &gpio->dat);
if (result)
printf("protect EEPROM failed !\n");
udelay(20000);
} while(result);
printf("verify MAC %pM ... ", mac);
i2c_read(SPD_EEPROM_ADDRESS, 0x80, 2, mac_verify, 6);
if (!strncmp((char *)mac, (char *)mac_verify, 6))
printf("ok.\n");
else
/* TODO: retry or do something useful */
printf("FAILED (got %pM) !\n", mac_verify);
}
}
return 0;
}
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return bus == 0 && cs == 0;
}
void spi_cs_activate(struct spi_slave *slave)
{
volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
iopd->dat &= ~TFT_SPI_CPLD_CS;
}
void spi_cs_deactivate(struct spi_slave *slave)
{
volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
iopd->dat |= TFT_SPI_CPLD_CS;
}
/* control backlight pwm (display brightness).
* allow values 0-250 with 0 = turn off and 250 = max brightness
*/
void mergerbox_tft_dim(u16 value)
{
struct spi_slave *slave;
u16 din;
u16 dout = 0;
if (value > 0 && value < 250)
dout = 0x4000 | value;
slave = spi_setup_slave(0, 0, 1000000, SPI_MODE_0 | SPI_CS_HIGH);
spi_claim_bus(slave);
spi_xfer(slave, 16, &dout, &din, SPI_XFER_BEGIN | SPI_XFER_END);
spi_release_bus(slave);
spi_free_slave(slave);
}
void ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
fdt_fixup_dr_usb(blob, bd);
ft_pci_setup(blob, bd);
}

View File

@ -1,61 +0,0 @@
/*
* Copyright (C) 2011 Matrix Vision GmbH
* Andre Schwarz <andre.schwarz@matrix-vision.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __MERGERBOX_H__
#define __MERGERBOX_H__
#define MV_GPIO
/*
* GPIO Bank 1
*/
#define TFT_SPI_EN (0x80000000>>0)
#define FPGA_CONFIG (0x80000000>>1)
#define FPGA_STATUS (0x80000000>>2)
#define FPGA_CONF_DONE (0x80000000>>3)
#define FPGA_DIN (0x80000000>>4)
#define FPGA_CCLK (0x80000000>>5)
#define MAN_RST (0x80000000>>6)
#define FPGA_SYS_RST (0x80000000>>7)
#define WD_WDI (0x80000000>>8)
#define TFT_RST (0x80000000>>9)
#define HISCON_GPIO1 (0x80000000>>10)
#define HISCON_GPIO2 (0x80000000>>11)
#define B2B_GPIO2 (0x80000000>>12)
#define CCU_GPIN (0x80000000>>13)
#define CCU_GPOUT (0x80000000>>14)
#define TFT_GPIO0 (0x80000000>>15)
#define TFT_GPIO1 (0x80000000>>16)
#define TFT_GPIO2 (0x80000000>>17)
#define TFT_GPIO3 (0x80000000>>18)
#define B2B_GPIO0 (0x80000000>>19)
#define B2B_GPIO1 (0x80000000>>20)
#define TFT_SPI_CPLD_CS (0x80000000>>21)
#define TFT_SPI_CS (0x80000000>>22)
#define CCU_PWR_EN (0x80000000>>23)
#define B2B_GPIO3 (0x80000000>>24)
#define CCU_PWR_STAT (0x80000000>>25)
#define MV_GPIO1_DAT (FPGA_CONFIG|CCU_PWR_EN|TFT_SPI_CPLD_CS)
#define MV_GPIO1_OUT (TFT_SPI_EN|FPGA_CONFIG|FPGA_DIN|FPGA_CCLK|CCU_PWR_EN| \
TFT_SPI_CPLD_CS)
#define MV_GPIO1_ODE (FPGA_CONFIG|MAN_RST)
/*
* GPIO Bank 2
*/
#define SPI_FLASH_WP (0x80000000>>10)
#define SYS_EEPROM_WP (0x80000000>>11)
#define SPI_FLASH_CS (0x80000000>>22)
#define MV_GPIO2_DAT (SYS_EEPROM_WP|SPI_FLASH_CS)
#define MV_GPIO2_OUT (SPI_FLASH_WP|SYS_EEPROM_WP|SPI_FLASH_CS)
#define MV_GPIO2_ODE 0
void mergerbox_tft_dim(u16 value);
#endif

View File

@ -1,128 +0,0 @@
/*
* Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
*
* Copyright (C) 2011 Matrix Vision GmbH
* Andre Schwarz <andre.schwarz@matrix-vision.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <mpc83xx.h>
#include <pci.h>
#include <asm/io.h>
#include <asm/fsl_mpc83xx_serdes.h>
#include "mergerbox.h"
#include "fpga.h"
#include "../common/mv_common.h"
static struct pci_region pci_regions[] = {
{
.bus_start = CONFIG_SYS_PCI_MEM_BASE,
.phys_start = CONFIG_SYS_PCI_MEM_PHYS,
.size = CONFIG_SYS_PCI_MEM_SIZE,
.flags = PCI_REGION_MEM | PCI_REGION_PREFETCH
},
{
.bus_start = CONFIG_SYS_PCI_MMIO_BASE,
.phys_start = CONFIG_SYS_PCI_MMIO_PHYS,
.size = CONFIG_SYS_PCI_MMIO_SIZE,
.flags = PCI_REGION_MEM
},
{
.bus_start = CONFIG_SYS_PCI_IO_BASE,
.phys_start = CONFIG_SYS_PCI_IO_PHYS,
.size = CONFIG_SYS_PCI_IO_SIZE,
.flags = PCI_REGION_IO
}
};
static struct pci_region pcie_regions_0[] = {
{
.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
.size = CONFIG_SYS_PCIE1_MEM_SIZE,
.flags = PCI_REGION_MEM,
},
{
.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
.size = CONFIG_SYS_PCIE1_IO_SIZE,
.flags = PCI_REGION_IO,
},
};
static struct pci_region pcie_regions_1[] = {
{
.bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
.phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
.size = CONFIG_SYS_PCIE2_MEM_SIZE,
.flags = PCI_REGION_MEM,
},
{
.bus_start = CONFIG_SYS_PCIE2_IO_BASE,
.phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
.size = CONFIG_SYS_PCIE2_IO_SIZE,
.flags = PCI_REGION_IO,
},
};
void pci_init_board(void)
{
volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
volatile sysconf83xx_t *sysconf = &immr->sysconf;
volatile clk83xx_t *clk = (clk83xx_t *)&immr->clk;
volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
volatile law83xx_t *pcie_law = sysconf->pcielaw;
struct pci_region *reg[] = { pci_regions };
struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
volatile gpio83xx_t *gpio;
gpio = (gpio83xx_t *)&immr->gpio[0];
gpio->dat = MV_GPIO1_DAT;
gpio->odr = MV_GPIO1_ODE;
gpio->dir = MV_GPIO1_OUT;
gpio = (gpio83xx_t *)&immr->gpio[1];
gpio->dat = MV_GPIO2_DAT;
gpio->odr = MV_GPIO2_ODE;
gpio->dir = MV_GPIO2_OUT;
printf("SICRH / SICRL : 0x%08x / 0x%08x\n", immr->sysconf.sicrh,
immr->sysconf.sicrl);
/* Enable PCI_CLK[0:1] */
clk->occr |= 0xc0000000;
udelay(2000);
mergerbox_init_fpga();
mv_load_fpga();
mergerbox_tft_dim(0);
/* Configure PCI Local Access Windows */
pci_law[0].bar = CONFIG_SYS_PCI_MEM_PHYS & LAWBAR_BAR;
pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
pci_law[1].bar = CONFIG_SYS_PCI_IO_PHYS & LAWBAR_BAR;
pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
udelay(2000);
mpc83xx_pci_init(1, reg);
/* Deassert the resets in the control register */
out_be32(&sysconf->pecr1, 0xE0008000);
out_be32(&sysconf->pecr2, 0xE0008000);
udelay(2000);
out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
mpc83xx_pcie_init(2, pcie_reg);
}

View File

@ -1,120 +0,0 @@
/*
* Copyright (C) 2011 Matrix Vision GmbH
* Andre Schwarz <andre.schwarz@matrix-vision.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <ns16550.h>
#include <netdev.h>
#include <sm501.h>
#include <pci.h>
#include "../common/mv_common.h"
#ifdef CONFIG_VIDEO
static const SMI_REGS init_regs_800x480[] = {
/* set endianess to little endian */
{0x0005c, 0x00000000},
/* PCI drive 12mA */
{0x00004, 0x42401001},
/* current clock */
{0x0003c, 0x310a1818},
/* clocks for pm0... */
{0x00040, 0x0002184f},
{0x00044, 0x2a1a0a01},
/* GPIO */
{0x10008, 0x00000000},
{0x1000C, 0x00000000},
/* panel control regs */
{0x80000, 0x0f017106},
{0x80004, 0x0},
{0x80008, 0x0},
{0x8000C, 0x00000000},
{0x80010, 0x0c800c80},
/* width 0x320 */
{0x80014, 0x03200000},
/* height 0x1e0 */
{0x80018, 0x01E00000},
{0x8001C, 0x0},
{0x80020, 0x01df031f},
{0x80024, 0x041f031f},
{0x80028, 0x00800347},
{0x8002C, 0x020c01df},
{0x80030, 0x000201e9},
{0x80200, 0x00000000},
/* ZV[0:7] */
{0x00008, 0x00ff0000},
/* 24-Bit TFT */
{0x0000c, 0x3f000000},
{0, 0}
};
/*
* Returns SM107 register base address. First thing called in the driver.
*/
unsigned int board_video_init(void)
{
pci_dev_t devbusfn;
u32 addr;
devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0);
if (devbusfn != -1) {
pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_1,
(u32 *)&addr);
return addr & 0xfffffffe;
}
return 0;
}
/*
* Called after initializing the SM501 and before clearing the screen.
*/
void board_validate_screen(unsigned int base)
{
}
/*
* Returns SM107 framebuffer address
*/
unsigned int board_video_get_fb(void)
{
pci_dev_t devbusfn;
u32 addr;
devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0);
if (devbusfn != -1) {
pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0,
(u32 *)&addr);
addr &= 0xfffffffe;
#ifdef CONFIG_VIDEO_SM501_FBMEM_OFFSET
addr += CONFIG_VIDEO_SM501_FBMEM_OFFSET;
#endif
return addr;
}
printf("board_video_get_fb(): FAILED\n");
return 0;
}
/*
* Return a pointer to the initialization sequence.
*/
const SMI_REGS *board_get_regs(void)
{
return init_regs_800x480;
}
int board_get_width(void)
{
return 800;
}
int board_get_height(void)
{
return 480;
}
#endif

View File

@ -1 +0,0 @@
bootscript.img

View File

@ -1,12 +0,0 @@
if TARGET_MVBLM7
config SYS_BOARD
default "mvblm7"
config SYS_VENDOR
default "matrix_vision"
config SYS_CONFIG_NAME
default "MVBLM7"
endif

View File

@ -1,6 +0,0 @@
MVBLM7 BOARD
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mvblm7/
F: include/configs/MVBLM7.h
F: configs/MVBLM7_defconfig

View File

@ -1,14 +0,0 @@
#
# Copyright (C) Freescale Semiconductor, Inc. 2006.
#
# SPDX-License-Identifier: GPL-2.0+
#
obj-y := mvblm7.o pci.o fpga.o
extra-y := bootscript.img
MKIMAGEFLAGS_bootscript.image := -T script -C none -n M7_script
$(obj)/bootscript.img: $(src)/bootscript
$(call cmd,mkimage)

View File

@ -1,84 +0,0 @@
Matrix Vision mvBlueLYNX-M7 (mvBL-M7)
-------------------------------------
1. Board Description
The mvBL-M7 is a 120x120mm single board computing platform
with strong focus on stereo image processing applications.
Power Supply is either VDC 12-48V or Pover over Ethernet (PoE)
on any port (requires add-on board).
2 System Components
2.1 CPU
Freescale MPC8343VRAGDB CPU running at 400MHz core and 266MHz csb.
512MByte DDR-II memory @ 133MHz.
8 MByte Nor Flash on local bus.
2 Vitesse VSC8601 RGMII ethernet Phys.
1 USB host controller over ULPI I/F.
2 serial ports. Console running on ttyS0 @ 115200 8N1.
1 SD-Card slot connected to SPI.
System configuration (HRCW) is taken from I2C EEPROM.
2.2 PCI
A miniPCI Type-III socket is present. PCI clock fixed at 66MHz.
2.3 FPGA
Altera Cyclone-II EP2C20/35 with PCI DMA engines.
Connects to dual Matrix Vision specific CCD/CMOS sensor interfaces.
Utilizes another 256MB DDR-II memory and 32-128MB Nand Flash.
2.3.1 I/O @ FPGA
2x8 Outputs : Infineon High-Side Switches to Main Supply.
2x8 Inputs : Programmable input threshold + trigger capabilities
2 dedicated flash interfaces for illuminator boards.
Cross trigger for chaining several boards.
2.4 I2C
Bus1:
MAX5381 DAC @ 0x60 for 1st digital input threshold.
LM75 @ 0x90 for temperature monitoring.
EEPROM @ 0xA0 for system setup (HRCW etc.) + vendor specifics.
1st image sensor interface (slave addresses depend on sensor)
Bus2:
MAX5381 DAC @ 0x60 for 2nd digital input threshold.
2nd image sensor interface (slave addresses depend on sensor)
3 Flash layout.
reset vector is 0xFFF00100, i.e. "HIGHBOOT".
FF800000 environment
FF802000 redundant environment
FF804000 u-boot script image
FF806000 redundant u-boot script image
FF808000 device tree blob
FF80A000 redundant device tree blob
FF80C000 tbd.
FF80E000 tbd.
FF810000 kernel
FFC00000 root FS
FFF00000 u-boot
FFF80000 FPGA raw bit file
mtd partitions are propagated to linux kernel via device tree blob.
4 Booting
On startup the bootscript @ FF804000 is executed. This script can be
exchanged easily. Default boot mode is "boot from flash", i.e. system
works stand-alone.
This behaviour depends on some environment variables :
"netboot" : yes ->try dhcp/bootp and boot from network.
A "dhcp_client_id" and "dhcp_vendor-class-identifier" can be used for
DHCP server configuration, e.g. to provide different images to
different devices.
During netboot the system tries to get 3 image files:
1. Kernel - name + data is given during BOOTP.
2. Initrd - name is stored in "initrd_name"
3. device tree blob - name is stored in "dtb_name"
Fallback files are the flash versions.

View File

@ -1,43 +0,0 @@
echo
echo "==== running autoscript ===="
echo
setenv bootdtb bootm \${kernel_boot} \${mv_initrd_addr_ram} \${mv_dtb_addr_ram}
setenv ramkernel setenv kernel_boot \${loadaddr}
setenv flashkernel setenv kernel_boot \${mv_kernel_addr}
setenv cpird cp \${mv_initrd_addr} \${mv_initrd_addr_ram} \${mv_initrd_length}
setenv bootfromflash run flashkernel cpird ramparam addcons bootdtb
setenv getdtb tftp \${mv_dtb_addr_ram} \${dtb_name}
setenv cpdtb cp \${mv_dtb_addr} \${mv_dtb_addr_ram} 0x2000
setenv rundtb fdt addr \${mv_dtb_addr_ram}\;fdt boardsetup
setenv bootfromnet tftp \${mv_initrd_addr_ram} \${initrd_name}\;run ramkernel
if test ${console} = yes;
then
setenv addcons setenv bootargs \${bootargs} console=ttyS\${console_nr},\${baudrate}N8
else
setenv addcons setenv bootargs \${bootargs} console=tty0
fi
setenv set_static_ip setenv ipaddr \${static_ipaddr}
setenv set_static_nm setenv netmask \${static_netmask}
setenv set_static_gw setenv gatewayip \${static_gateway}
setenv set_ip setenv ip \${ipaddr}::\${gatewayip}:\${netmask}
setenv ramparam setenv bootargs root=/dev/ram0 ro rootfstype=squashfs
if test ${autoscript_boot} != no;
then
if test ${netboot} = yes;
then
bootp
if test $? = 0;
then
echo "=== bootp succeeded -> netboot ==="
run set_ip
run getdtb rundtb bootfromnet ramparam addcons bootdtb
else
echo "=== netboot failed ==="
fi
fi
run set_static_ip set_static_nm set_static_gw set_ip
echo "=== bootfromflash ==="
run cpdtb rundtb bootfromflash
else
echo "=== boot stopped with autoscript_boot no ==="
fi

View File

@ -1,169 +0,0 @@
/*
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com.
*
* (C) Copyright 2008
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <ACEX1K.h>
#include <command.h>
#include "fpga.h"
#include "mvblm7.h"
#ifdef FPGA_DEBUG
#define fpga_debug(fmt, args...) printf("%s: "fmt, __func__, ##args)
#else
#define fpga_debug(fmt, args...)
#endif
Altera_CYC2_Passive_Serial_fns altera_fns = {
fpga_null_fn,
fpga_config_fn,
fpga_status_fn,
fpga_done_fn,
fpga_wr_fn,
fpga_null_fn,
fpga_null_fn,
};
Altera_desc cyclone2 = {
Altera_CYC2,
passive_serial,
Altera_EP2C20_SIZE,
(void *) &altera_fns,
NULL,
0
};
DECLARE_GLOBAL_DATA_PTR;
int mvblm7_init_fpga(void)
{
fpga_debug("Initialize FPGA interface\n");
fpga_init();
fpga_add(fpga_altera, &cyclone2);
fpga_config_fn(0, 1, 0);
udelay(60);
return 1;
}
int fpga_null_fn(int cookie)
{
return 0;
}
int fpga_config_fn(int assert, int flush, int cookie)
{
volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
u32 dvo = gpio->dat;
fpga_debug("SET config : %s\n", assert ? "low" : "high");
if (assert)
dvo |= FPGA_CONFIG;
else
dvo &= ~FPGA_CONFIG;
if (flush)
gpio->dat = dvo;
return assert;
}
int fpga_done_fn(int cookie)
{
volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
int result = 0;
udelay(10);
fpga_debug("CONF_DONE check ... ");
if (gpio->dat & FPGA_CONF_DONE) {
fpga_debug("high\n");
result = 1;
} else
fpga_debug("low\n");
return result;
}
int fpga_status_fn(int cookie)
{
volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
int result = 0;
fpga_debug("STATUS check ... ");
if (gpio->dat & FPGA_STATUS) {
fpga_debug("high\n");
result = 1;
} else
fpga_debug("low\n");
return result;
}
int fpga_clk_fn(int assert_clk, int flush, int cookie)
{
volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
u32 dvo = gpio->dat;
fpga_debug("CLOCK %s\n", assert_clk ? "high" : "low");
if (assert_clk)
dvo |= FPGA_CCLK;
else
dvo &= ~FPGA_CCLK;
if (flush)
gpio->dat = dvo;
return assert_clk;
}
static inline int _write_fpga(u8 val, int dump)
{
volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
int i;
u32 dvo = gpio->dat;
if (dump)
fpga_debug(" %02x -> ", val);
for (i = 0; i < 8; i++) {
dvo &= ~FPGA_CCLK;
gpio->dat = dvo;
dvo &= ~FPGA_DIN;
if (dump)
fpga_debug("%d ", val&1);
if (val & 1)
dvo |= FPGA_DIN;
gpio->dat = dvo;
dvo |= FPGA_CCLK;
gpio->dat = dvo;
val >>= 1;
}
if (dump)
fpga_debug("\n");
return 0;
}
int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie)
{
unsigned char *data = (unsigned char *) buf;
int i;
fpga_debug("fpga_wr: buf %p / size %d\n", buf, len);
for (i = 0; i < len; i++)
_write_fpga(data[i], 0);
fpga_debug("\n");
return FPGA_SUCCESS;
}

View File

@ -1,17 +0,0 @@
/*
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
extern int mvblm7_init_fpga(void);
extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
extern int fpga_status_fn(int cookie);
extern int fpga_config_fn(int assert, int flush, int cookie);
extern int fpga_done_fn(int cookie);
extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
extern int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie);
extern int fpga_null_fn(int cookie);

View File

@ -1,136 +0,0 @@
/*
* Copyright (C) Freescale Semiconductor, Inc. 2006.
*
* (C) Copyright 2008
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <ioports.h>
#include <mpc83xx.h>
#include <asm/mpc8349_pci.h>
#include <pci.h>
#include <spi.h>
#include <asm/mmu.h>
#if defined(CONFIG_OF_LIBFDT)
#include <libfdt.h>
#endif
#include "../common/mv_common.h"
#include "mvblm7.h"
int fixed_sdram(void)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
u32 msize = 0;
u32 ddr_size;
u32 ddr_size_log2;
char *s = getenv("ddr_size");
msize = CONFIG_SYS_DDR_SIZE;
if (s) {
u32 env_ddr_size = simple_strtoul(s, NULL, 10);
if (env_ddr_size == 512)
msize = 512;
}
for (ddr_size = msize << 20, ddr_size_log2 = 0;
(ddr_size > 1);
ddr_size = ddr_size >> 1, ddr_size_log2++) {
if (ddr_size & 1)
return -1;
}
im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
im->sysconf.ddrlaw[0].ar = LAWAR_EN | ((ddr_size_log2 - 1) &
LAWAR_SIZE);
im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
asm("sync;isync");
udelay(600);
im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
asm("sync;isync");
udelay(500);
return msize;
}
phys_size_t initdram(int board_type)
{
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
u32 msize = 0;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
return -1;
im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
msize = fixed_sdram();
/* return total bus RAM size(bytes) */
return msize * 1024 * 1024;
}
int misc_init_r(void)
{
char *s = getenv("reset_env");
if (s) {
mv_reset_environment();
}
return 0;
}
int checkboard(void)
{
puts("Board: Matrix Vision mvBlueLYNX-M7\n");
return 0;
}
#ifdef CONFIG_HARD_SPI
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return bus == 0 && cs == 0;
}
void spi_cs_activate(struct spi_slave *slave)
{
volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
iopd->dat &= ~MVBLM7_MMC_CS;
}
void spi_cs_deactivate(struct spi_slave *slave)
{
volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
iopd->dat |= ~MVBLM7_MMC_CS;
}
#endif
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
#ifdef CONFIG_PCI
ft_pci_setup(blob, bd);
#endif
}
#endif

View File

@ -1,20 +0,0 @@
#ifndef __MVBC_H__
#define __MVBC_H__
#define MV_GPIO
#define FPGA_CONFIG 0x80000000
#define FPGA_CCLK 0x40000000
#define FPGA_DIN 0x20000000
#define FPGA_STATUS 0x10000000
#define FPGA_CONF_DONE 0x08000000
#define WD_WDI 0x00400000
#define WD_TS 0x00200000
#define MAN_RST 0x00100000
#define MV_GPIO_DAT (WD_TS)
#define MV_GPIO_OUT (FPGA_CONFIG|FPGA_DIN|FPGA_CCLK|MVBLM7_MMC_CS)
#define MV_GPIO_ODE (FPGA_CONFIG|MAN_RST)
#endif

View File

@ -1,89 +0,0 @@
/*
* Copyright (C) Freescale Semiconductor, Inc. 2006.
*
* (C) Copyright 2008
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#if defined(CONFIG_OF_LIBFDT)
#include <libfdt.h>
#endif
#include <pci.h>
#include <mpc83xx.h>
#include <fpga.h>
#include "mvblm7.h"
#include "fpga.h"
#include "../common/mv_common.h"
DECLARE_GLOBAL_DATA_PTR;
static struct pci_region pci_regions[] = {
{
bus_start: CONFIG_SYS_PCI1_MEM_BASE,
phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
size: CONFIG_SYS_PCI1_MEM_SIZE,
flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
},
{
bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
size: CONFIG_SYS_PCI1_MMIO_SIZE,
flags: PCI_REGION_MEM
},
{
bus_start: CONFIG_SYS_PCI1_IO_BASE,
phys_start: CONFIG_SYS_PCI1_IO_PHYS,
size: CONFIG_SYS_PCI1_IO_SIZE,
flags: PCI_REGION_IO
}
};
void pci_init_board(void)
{
int i;
volatile immap_t *immr;
volatile pcictrl83xx_t *pci_ctrl;
volatile gpio83xx_t *gpio;
volatile clk83xx_t *clk;
volatile law83xx_t *pci_law;
struct pci_region *reg[] = { pci_regions };
immr = (immap_t *) CONFIG_SYS_IMMR;
clk = (clk83xx_t *) &immr->clk;
pci_ctrl = immr->pci_ctrl;
pci_law = immr->sysconf.pcilaw;
gpio = (volatile gpio83xx_t *)&immr->gpio[0];
gpio->dat = MV_GPIO_DAT;
gpio->odr = MV_GPIO_ODE;
gpio->dir = MV_GPIO_OUT;
printf("SICRH / SICRL : 0x%08x / 0x%08x\n", immr->sysconf.sicrh,
immr->sysconf.sicrl);
mvblm7_init_fpga();
mv_load_fpga();
gpio->dir = MV_GPIO_OUT & ~(FPGA_DIN|FPGA_CCLK);
/* Enable PCI_CLK_OUTPUTs 0 and 1 with 1:1 clocking */
clk->occr = 0xc0000000;
pci_ctrl[0].gcr = 0;
udelay(2000);
pci_ctrl[0].gcr = 1;
for (i = 0; i < 1000; ++i)
udelay(1000);
pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
pci_law[0].ar = LBLAWAR_EN | LBLAWAR_1GB;
pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
mpc83xx_pci_init(1, reg);
}

View File

@ -1,3 +0,0 @@
CONFIG_PPC=y
CONFIG_MPC83xx=y
CONFIG_TARGET_MERGERBOX=y

View File

@ -1,3 +0,0 @@
CONFIG_PPC=y
CONFIG_MPC83xx=y
CONFIG_TARGET_MVBLM7=y

View File

@ -12,6 +12,8 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
MERGERBOX powerpc mpc83xx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
MVBLM7 powerpc mpc83xx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
bluestone powerpc ppc4xx - - Tirumala Marri <tmarri@apm.com>
CRAYL1 powerpc ppc4xx - - David Updegraff <dave@cray.com>
KAREF powerpc ppc4xx - - Travis Sawyer <travis.sawyer@sandburst.com>

View File

@ -1,599 +0,0 @@
/*
* Copyright (C) 2007 Freescale Semiconductor, Inc.
*
* Copyright (C) 2011 Matrix Vision GmbH
* Andre Schwarz <andre.schwarz@matrix-vision.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <version.h>
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1
#define CONFIG_MPC837x 1
#define CONFIG_MPC8377 1
#define CONFIG_SYS_TEXT_BASE 0xFC000000
#define CONFIG_PCI 1
#define CONFIG_PCI_INDIRECT_BRIDGE 1
#define CONFIG_MASK_AER_AO
#define CONFIG_DISPLAY_AER_FULL
#define CONFIG_MISC_INIT_R
/*
* On-board devices
*/
#define CONFIG_TSEC_ENET
/*
* System Clock Setup
*/
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
#define CONFIG_PCIE
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
/*
* Hardware Reset Configuration Word stored in EEPROM.
*/
#define CONFIG_SYS_HRCW_LOW 0
#define CONFIG_SYS_HRCW_HIGH 0
/* Arbiter Configuration Register */
#define CONFIG_SYS_ACR_PIPE_DEP 3
#define CONFIG_SYS_ACR_RPTCNT 3
/* System Priority Control Regsiter */
#define CONFIG_SYS_SPCR_TSECEP 3
/* System Clock Configuration Register */
#define CONFIG_SYS_SCCR_TSEC1CM 3
#define CONFIG_SYS_SCCR_TSEC2CM 0
#define CONFIG_SYS_SCCR_SDHCCM 3
#define CONFIG_SYS_SCCR_ENCCM 3 /* also clock for I2C-1 */
#define CONFIG_SYS_SCCR_USBDRCM CONFIG_SYS_SCCR_ENCCM /* must match */
#define CONFIG_SYS_SCCR_PCIEXP1CM 3
#define CONFIG_SYS_SCCR_PCIEXP2CM 3
#define CONFIG_SYS_SCCR_PCICM 1
#define CONFIG_SYS_SCCR_SATACM 0xFF
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH 0x087c0000
#define CONFIG_SYS_SICRL 0x40000000
/*
* Output Buffer Impedance
*/
#define CONFIG_SYS_OBIR 0x30000000
/*
* IMMR new address
*/
#define CONFIG_SYS_IMMR 0xE0000000
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_83XX_DDR_USES_CS0
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN | DDRCDR_PZ_HIZ |\
DDRCDR_NZ_HIZ | DDRCDR_ODT |\
DDRCDR_Q_DRN)
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDR_MODE_WEAK
#define CONFIG_SYS_DDR_WRITE_DATA_DELAY 2
#define CONFIG_SYS_DDR_CPO 0x1f
/* SPD table located at offset 0x20 in extended adressing ROM
* used for HRCW fetch after power-on reset
*/
#define CONFIG_SPD_EEPROM
#define SPD_EEPROM_ADDRESS 0x50
#define SPD_EEPROM_OFFSET 0x20
#define SPD_EEPROM_ADDR_LEN 2
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (512*1024)
#define CONFIG_SYS_MALLOC_LEN (512*1024)
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
GENERATED_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_FSL_ELBC 1
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_FLASH_SIZE 64
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 |\
BR_MS_GPCM | BR_V)
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_FLASH_BASE | OR_UPM_XAM |\
OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 |\
OR_GPCM_XACS | OR_GPCM_SCY_15 |\
OR_GPCM_TRLX_SET | OR_GPCM_EHTR_SET |\
OR_GPCM_EAD)
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 512
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/*
* NAND Flash on the Local Bus
*/
#define CONFIG_MTD_NAND_VERIFY_WRITE 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_NAND_FSL_ELBC 1
#define CONFIG_SYS_NAND_BASE 0xE0600000
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | BR_DECC_CHK_GEN |\
BR_PS_8 | BR_MS_FCM | BR_V)
#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_FCM_BCTLD | OR_FCM_CST |\
OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_RST |\
OR_FCM_TRLX | OR_FCM_EHTR)
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
#define CONFIG_CONSOLE ttyS0
#define CONFIG_BAUDRATE 115200
/* SERDES */
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1 0xe3000
#define CONFIG_FSL_SERDES2 0xe3100
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
#define CONFIG_SYS_PCI_MEM_SIZE (256 << 20)
#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
#define CONFIG_SYS_PCI_MMIO_SIZE (256 << 20)
#define CONFIG_SYS_PCI_IO_BASE 0x00000000
#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
#define CONFIG_SYS_PCI_IO_SIZE (1 << 20)
#ifdef CONFIG_PCIE
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE (128 << 20)
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
#define CONFIG_SYS_PCIE1_MEM_SIZE (256 << 20)
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
#define CONFIG_SYS_PCIE1_IO_SIZE (8 << 20)
#define CONFIG_SYS_PCIE2_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_CFG_SIZE (128 << 20)
#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
#define CONFIG_SYS_PCIE2_MEM_SIZE (256 << 20)
#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
#define CONFIG_SYS_PCIE2_IO_SIZE (8 << 20)
#endif
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
/*
* TSEC
*/
#define CONFIG_GMII /* MII PHY management */
#define CONFIG_SYS_VSC8601_SKEWFIX
#define CONFIG_SYS_VSC8601_SKEW_TX 3
#define CONFIG_SYS_VSC8601_SKEW_RX 3
#define CONFIG_TSEC1
#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 0x10
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_HAS_ETH0
/*
* SATA
*/
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1_OFFSET 0x18000
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2_OFFSET 0x19000
#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_VENDOREX
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_NTPSERVER
#define CONFIG_BOOTP_RANDOM_DELAY
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_LIB_RAND
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PING
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PCI
#define CONFIG_CMD_USB
#define CONFIG_CMD_SPI
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_SATA
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_JFFS2
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=NOR,nand0=NAND"
#define MTDPARTS_DEFAULT "mtdparts=NOR:1M(u-boot),2M(FPGA);NAND:-(root)"
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE 1
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_LOAD_ADDR 0x2000000
#define CONFIG_LOADADDR 0x4000000
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
#define CONFIG_SYS_MEMTEST_START (60<<20)
#define CONFIG_SYS_MEMTEST_END (70<<20)
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
*/
#define CONFIG_HIGH_BATS 1
/* DDR: cache cacheable */
#define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM | BATL_PP_RW |\
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM | BATU_BL_256M | BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* unused */
#define CONFIG_SYS_IBAT1L (0)
#define CONFIG_SYS_IBAT1U (0)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_RW |\
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* unused */
#define CONFIG_SYS_IBAT3L (0)
#define CONFIG_SYS_IBAT3U (0)
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW |\
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_64M |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_RW |\
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_RW | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* I2C EEPROM settings
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_SIZE 0x4000
/*
* Environment Configuration
*/
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR 0xFFD00000
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
/*
* Video
*/
#define CONFIG_VIDEO
#define CONFIG_VIDEO_SM501_PCI
#define VIDEO_FB_LITTLE_ENDIAN
#define CONFIG_CMD_BMP
#define CONFIG_VIDEO_SM501
#define CONFIG_VIDEO_SM501_32BPP
#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_VIDEO_BMP_GZIP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
/*
* SPI
*/
#define CONFIG_MPC8XXX_SPI
/*
* USB
*/
#define CONFIG_SYS_USB_HOST
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_STORAGE
#define CONFIG_USB_KEYBOARD
/*
*
*/
#define CONFIG_BOOTDELAY 5
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_STOP_STR "s"
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_RESET_TO_RETRY 1000
#define MV_CI "MergerBox"
#define MV_VCI "MergerBox"
#define MV_FPGA_DATA 0xfc100000
#define MV_FPGA_SIZE 0x00200000
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define MV_KERNEL_ADDR_RAM 0x02800000
#define MV_DTB_ADDR_RAM 0x00600000
#define MV_INITRD_ADDR_RAM 0x01000000
#define MV_FITADDR 0xfc300000
#define MV_SPLAH_ADDR 0xffe00000
#define CONFIG_BOOTCOMMAND "run i2c_init;if test ${boot_sqfs} -eq 1;"\
"then; run fitboot;else;run ubiboot;fi;"
#define CONFIG_BOOTARGS "console=ttyS0,115200n8"
#define CONFIG_EXTRA_ENV_SETTINGS \
"console_nr=0\0"\
"stdin=serial\0"\
"stdout=serial\0"\
"stderr=serial\0"\
"boot_sqfs=1\0"\
"usb_dr_mode=host\0"\
"bootfile=MergerBox.fit\0"\
"baudrate=" __stringify(CONFIG_BAUDRATE) "\0"\
"fpga=0\0"\
"fpgadata=" __stringify(MV_FPGA_DATA) "\0"\
"fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"\
"mv_kernel_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"\
"mv_initrd_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"\
"mv_dtb_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"\
"uboota=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"\
"fitaddr=" __stringify(MV_FITADDR) "\0"\
"mv_version=" U_BOOT_VERSION "\0"\
"mtdids=" MTDIDS_DEFAULT "\0"\
"mtdparts=" MTDPARTS_DEFAULT "\0"\
"dhcp_client_id=" MV_CI "\0"\
"dhcp_vendor-class-identifier=" MV_VCI "\0"\
"upd_uboot=dhcp;tftp bdi2000/u-boot-mergerbox-xp.bin;"\
"protect off all;erase $uboota +0xC0000;"\
"cp.b $loadaddr $uboota $filesize\0"\
"upd_fpga=dhcp;tftp MergerBox.rbf;erase $fpgadata +$fpgadatasize;"\
"cp.b $loadaddr $fpgadata $filesize\0"\
"upd_fit=dhcp;tftp MergerBox.fit;erase $fitaddr +0x1000000;"\
"cp.b $loadaddr $fitaddr $filesize\0"\
"addsqshrfs=set bootargs $bootargs root=/dev/ram ro "\
"rootfstype=squashfs\0"\
"addubirfs=set bootargs $bootargs ubi.mtd=9 root=ubi0:rootfs rw "\
"rootfstype=ubifs\0"\
"addusbrfs=set bootargs $bootargs root=/dev/sda1 rw "\
"rootfstype=ext3 usb-storage.delay_use=1 rootdelay=3\0"\
"netusbboot=bootp;run fpganetload fitnetload addusbrfs doboot\0"\
"netubiboot= bootp;run fpganetload fitnetload addubirfs doboot\0"\
"ubiboot=run fitprep addubirfs;set mv_initrd_ram -;run doboot\0"\
"doboot=bootm $mv_kernel_ram $mv_initrd_ram $mv_dtb_ram\0"\
"fitprep=imxtract $fitaddr kernel $mv_kernel_ram;"\
"imxtract $fitaddr ramdisk $mv_initrd_ram;"\
"imxtract $fitaddr fdt $mv_dtb_ram\0"\
"fdtprep=fdt addr $mv_dtb_ram;fdt boardsetup\0"\
"fitboot=run fitprep fdtprep addsqshrfs doboot\0"\
"i2c_init=run i2c_speed init_sdi_tx i2c_init_pll\0"\
"i2c_init_pll=i2c mw 65 9 2;i2c mw 65 9 0;i2c mw 65 5 2b;"\
"i2c mw 65 7 f;i2c mw 65 8 f;i2c mw 65 11 40;i2c mw 65 12 40;"\
"i2c mw 65 13 40; i2c mw 65 14 40; i2c mw 65 a 0\0"\
"i2c_speed=i2c dev 0;i2c speed 300000;i2c dev 1;i2c speed 120000\0"\
"init_sdi_tx=i2c mw 21 6 0;i2c mw 21 2 0;i2c mw 21 3 0;sleep 1;"\
"i2c mw 21 2 ff;i2c mw 21 3 3c\0"\
"splashimage=" __stringify(MV_SPLAH_ADDR) "\0"\
""
/*
* FPGA
*/
#define CONFIG_FPGA_COUNT 1
#define CONFIG_FPGA
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_CYCLON2
#endif

View File

@ -1,491 +0,0 @@
/*
* Copyright (C) Matrix Vision GmbH 2008
*
* Matrix Vision mvBlueLYNX-M7 configuration file
* based on Freescale's MPC8349ITX.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <version.h>
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1
#define CONFIG_MPC834x 1
#define CONFIG_MPC8343 1
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
#define CONFIG_SYS_IMMR 0xE0000000
#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_SKIP_HOST_BRIDGE
#define CONFIG_TSEC_ENET
#define CONFIG_MPC8XXX_SPI
#define CONFIG_HARD_SPI
#define MVBLM7_MMC_CS 0x04000000
#define CONFIG_MISC_INIT_R
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 100000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED 100000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* DDR Setup
*/
#undef CONFIG_SPD_EEPROM
#define CONFIG_SYS_DDR_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_83XX_DDR_USES_CS0 1
#define CONFIG_SYS_MEMTEST_START (60<<20)
#define CONFIG_SYS_MEMTEST_END (70<<20)
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDRCDR (DDRCDR_PZ_HIZ \
| DDRCDR_NZ_HIZ \
| DDRCDR_Q_DRN)
/* 0x22000001 */
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDR_SIZE 512
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
#define CONFIG_SYS_DDR_TIMING_0 0x00260802
#define CONFIG_SYS_DDR_TIMING_1 0x3837c322
#define CONFIG_SYS_DDR_TIMING_2 0x0f9848c6
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_SDRAM_CFG 0x43080008
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
#define CONFIG_SYS_DDR_INTERVAL 0x02000100
#define CONFIG_SYS_DDR_MODE 0x04040242
#define CONFIG_SYS_DDR_MODE2 0x00800000
/* Flash */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BASE 0xFF800000
#define CONFIG_SYS_FLASH_SIZE 8
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000
#define CONFIG_SYS_FLASH_WRITE_TOUT 500
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 256
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
| BR_PS_16 \
| BR_MS_GPCM \
| BR_V)
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 \
| OR_GPCM_XACS \
| OR_GPCM_SCY_15 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EHTR_SET \
| OR_GPCM_EAD)
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
/*
* U-Boot memory configuration
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#undef CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
/*
* Local Bus LCRR and LBCR regs
* LCRR: DLL bypass, Clock divider is 4
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/* LB sdram refresh timer, about 6us */
#define CONFIG_SYS_LBC_LSRT 0x32000000
/* LB refresh timer prescal, 266MHz/32*/
#define CONFIG_SYS_LBC_MRTPR 0x20000000
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_CONSOLE ttyS0
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
#define MV_DTB_NAME "mvblm7.dtb"
/*
* PCI
*/
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCI1_MMIO_BASE \
(CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000
#define CONFIG_NET_RETRY_COUNT 3
#define CONFIG_PCI_66M
#define CONFIG_83XX_CLKIN 66666667
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
/* TSEC */
#define CONFIG_GMII
#define CONFIG_SYS_VSC8601_SKEWFIX
#define CONFIG_SYS_VSC8601_SKEW_TX 3
#define CONFIG_SYS_VSC8601_SKEW_RX 3
#define CONFIG_TSEC1
#define CONFIG_TSEC2
#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_FEC1_PHY_NORXERR
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define TSEC1_PHY_ADDR 0x10
#define TSEC1_PHYIDX 0
#define TSEC1_FLAGS (TSEC_GIGABIT|TSEC_REDUCED)
#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME "TSEC1"
#define CONFIG_FEC2_PHY_NORXERR
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
#define TSEC2_PHY_ADDR 0x11
#define TSEC2_PHYIDX 0
#define TSEC2_FLAGS (TSEC_GIGABIT|TSEC_REDUCED)
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_BOOTP_VENDOREX
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_NTPSERVER
#define CONFIG_BOOTP_RANDOM_DELAY
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_LIB_RAND
/* USB */
#define CONFIG_SYS_USB_HOST
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* Environment
*/
#undef CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR 0xFF800000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_LOADS_ECHO
#define CONFIG_SYS_LOADS_BAUD_CHANGE
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_PCI
#define CONFIG_CMD_I2C
#define CONFIG_CMD_FPGA
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_USB
#define CONFIG_DOS_PARTITION
#undef CONFIG_WATCHDOG
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_HUSH_PARSER
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x2000000
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 0x200000
#define CONFIG_SYS_PROMPT "mvBL-M7> "
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
#define CONFIG_SYS_HRCW_LOW 0x0
#define CONFIG_SYS_HRCW_HIGH 0x0
/*
* System performance
*/
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
/* clocking */
#define CONFIG_SYS_SCCR_ENCCM 0
#define CONFIG_SYS_SCCR_USBMPHCM 0
#define CONFIG_SYS_SCCR_USBDRCM 2
#define CONFIG_SYS_SCCR_TSEC1CM 1
#define CONFIG_SYS_SCCR_TSEC2CM 1
#define CONFIG_SYS_SICRH 0x1fef0003
#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1 | SICRL_USB0)
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \
HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2 HID2_HBE
#define CONFIG_HIGH_BATS 1
/* DDR */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
/* PCI */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
/* no PCI2 */
#define CONFIG_SYS_IBAT3L 0
#define CONFIG_SYS_IBAT3U 0
#define CONFIG_SYS_IBAT4L 0
#define CONFIG_SYS_IBAT4U 0
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFF800000 */
#define CONFIG_SYS_IBAT6L (0xF0000000 \
| BATL_PP_RW \
| BATL_MEMCOHERENCE \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_IBAT7L 0
#define CONFIG_SYS_IBAT7U 0
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#define CONFIG_NETDEV eth0
/* Default path and filenames */
#define CONFIG_BOOTDELAY 5
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_STOP_STR "s"
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_RESET_TO_RETRY 1000
#define MV_CI "mvBL-M7"
#define MV_VCI "mvBL-M7"
#define MV_FPGA_DATA 0xfff40000
#define MV_FPGA_SIZE 0
#define MV_KERNEL_ADDR 0xff810000
#define MV_INITRD_ADDR 0xffb00000
#define MV_SCRIPT_ADDR 0xff804000
#define MV_SCRIPT_ADDR2 0xff806000
#define MV_DTB_ADDR 0xff808000
#define MV_INITRD_LENGTH 0x00400000
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define MV_KERNEL_ADDR_RAM 0x00100000
#define MV_DTB_ADDR_RAM 0x00600000
#define MV_INITRD_ADDR_RAM 0x01000000
#define CONFIG_BOOTCOMMAND "if imi ${script_addr}; " \
"then source ${script_addr}; " \
"else source ${script_addr2}; " \
"fi;"
#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs"
#define CONFIG_EXTRA_ENV_SETTINGS \
"console_nr=0\0" \
"baudrate=" __stringify(CONFIG_BAUDRATE) "\0" \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0" \
"fpga=0\0" \
"fpgadata=" __stringify(MV_FPGA_DATA) "\0" \
"fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \
"script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \
"script_addr2=" __stringify(MV_SCRIPT_ADDR2) "\0" \
"mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \
"mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \
"mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \
"mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \
"mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \
"mv_dtb_addr=" __stringify(MV_DTB_ADDR) "\0" \
"mv_dtb_addr_ram=" __stringify(MV_DTB_ADDR_RAM) "\0" \
"dtb_name=" __stringify(MV_DTB_NAME) "\0" \
"mv_version=" U_BOOT_VERSION "\0" \
"dhcp_client_id=" MV_CI "\0" \
"dhcp_vendor-class-identifier=" MV_VCI "\0" \
"netretry=no\0" \
"use_static_ipaddr=no\0" \
"static_ipaddr=192.168.90.10\0" \
"static_netmask=255.255.255.0\0" \
"static_gateway=0.0.0.0\0" \
"initrd_name=uInitrd.mvBL-M7-rfs\0" \
"zcip=no\0" \
"netboot=yes\0" \
"mvtest=Ff\0" \
"tried_bootfromflash=no\0" \
"tried_bootfromnet=no\0" \
"bootfile=mvblm72625.boot\0" \
"use_dhcp=yes\0" \
"gev_start=yes\0" \
"mvbcdma_debug=0\0" \
"mvbcia_debug=0\0" \
"propdev_debug=0\0" \
"gevss_debug=0\0" \
"watchdog=0\0" \
"usb_dr_mode=host\0" \
"sensor_cnt=2\0" \
""
#define CONFIG_FPGA_COUNT 1
#define CONFIG_FPGA
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_CYCLON2
#endif