diff --git a/arch/arm/dts/r7s72100-gr-peach-u-boot.dts b/arch/arm/dts/r7s72100-gr-peach-u-boot.dts index 28247d19d7..30e35e47d6 100644 --- a/arch/arm/dts/r7s72100-gr-peach-u-boot.dts +++ b/arch/arm/dts/r7s72100-gr-peach-u-boot.dts @@ -37,6 +37,15 @@ }; }; + reg_usbhs0_vbus: regulator-usbhs0-vbus { + compatible = "regulator-fixed"; + regulator-name = "usbhs0_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&port4 1 GPIO_ACTIVE_LOW>; + }; + + rpc: rpc@0xee200000 { compatible = "renesas,rpc-r7s72100", "renesas,rpc"; reg = <0x3fefa000 0x100>, <0x18000000 0x08000000>; @@ -76,3 +85,8 @@ &scif2_pins { u-boot,dm-pre-reloc; }; + +&usbhs0 { + vbus-supply = <®_usbhs0_vbus>; + status = "okay"; +}; diff --git a/configs/grpeach_defconfig b/configs/grpeach_defconfig index 2209f47e6d..4a243d679f 100644 --- a/configs/grpeach_defconfig +++ b/configs/grpeach_defconfig @@ -10,6 +10,7 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_ELF is not set CONFIG_CMD_GPIO=y CONFIG_CMD_SF=y +CONFIG_CMD_USB=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y @@ -30,7 +31,7 @@ CONFIG_ENV_SPI_MAX_HZ=50000000 CONFIG_USE_ENV_SPI_MODE=y CONFIG_ENV_SPI_MODE=0x0 CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_HAVE_BLOCK_DEVICE=y +CONFIG_BLK=y CONFIG_DM_GPIO=y CONFIG_RZA1_GPIO=y CONFIG_LED=y @@ -43,11 +44,17 @@ CONFIG_SPI_FLASH_MACRONIX=y CONFIG_DM_ETH=y CONFIG_SH_ETHER=y CONFIG_PINCTRL=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y CONFIG_SCIF_CONSOLE=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_RENESAS_RPC_SPI=y CONFIG_TIMER=y CONFIG_RENESAS_OSTM_TIMER=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_R8A66597_HCD=y +CONFIG_USB_STORAGE=y CONFIG_OF_LIBFDT_OVERLAY=y # CONFIG_EFI_LOADER is not set diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 42046c8062..30c6b69be8 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -300,3 +300,12 @@ config USB_DWC2_BUFFER_SIZE because larger transactions could be split in smaller ones. endif # USB_DWC2 + +config USB_R8A66597_HCD + bool "Renesas R8A66597 USB Core support" + depends on OF_CONTROL + depends on DM_USB + select USB_HOST + ---help--- + This enables support for the on-chip Renesas R8A66597 USB 2.0 + controller, present in various RZ and SH SoCs. diff --git a/drivers/usb/host/r8a66597-hcd.c b/drivers/usb/host/r8a66597-hcd.c index 3c263e51c1..a37696d83f 100644 --- a/drivers/usb/host/r8a66597-hcd.c +++ b/drivers/usb/host/r8a66597-hcd.c @@ -7,9 +7,11 @@ #include #include +#include #include #include #include +#include #include "r8a66597.h" @@ -19,33 +21,53 @@ #define R8A66597_DPRINT(...) #endif -static struct r8a66597 gr8a66597; +static inline struct usb_device *usb_dev_get_parent(struct usb_device *udev) +{ + struct udevice *parent = udev->dev->parent; + + /* + * When called from usb-uclass.c: usb_scan_device() udev->dev points + * to the parent udevice, not the actual udevice belonging to the + * udev as the device is not instantiated yet. + * + * If dev is an usb-bus, then we are called from usb_scan_device() for + * an usb-device plugged directly into the root port, return NULL. + */ + if (device_get_uclass_id(udev->dev) == UCLASS_USB) + return NULL; + + /* + * If these 2 are not the same we are being called from + * usb_scan_device() and udev itself is the parent. + */ + if (dev_get_parent_priv(udev->dev) != udev) + return udev; + + /* We are being called normally, use the parent pointer */ + if (device_get_uclass_id(parent) == UCLASS_USB_HUB) + return dev_get_parent_priv(parent); + + return NULL; +} static void get_hub_data(struct usb_device *dev, u16 *hub_devnum, u16 *hubport) { - int i; + struct usb_device *parent = usb_dev_get_parent(dev); *hub_devnum = 0; *hubport = 0; /* check a device connected to root_hub */ - if ((dev->parent && dev->parent->devnum == 1) || - (dev->devnum == 1)) + if ((parent && parent->devnum == 1) || + dev->devnum == 1) return; - for (i = 0; i < USB_MAXCHILDREN; i++) { - if (dev->parent->children[i] == dev) { - *hub_devnum = (u8)dev->parent->devnum; - *hubport = i; - return; - } - } - - printf("get_hub_data error.\n"); + *hub_devnum = (u8)parent->devnum; + *hubport = parent->portnr - 1; } static void set_devadd(struct r8a66597 *r8a66597, u8 r8a66597_address, - struct usb_device *dev, int port) + struct usb_device *dev, int port) { u16 val, usbspd, upphub, hubport; unsigned long devadd_reg = get_devadd_addr(r8a66597_address); @@ -61,17 +83,6 @@ static int r8a66597_clock_enable(struct r8a66597 *r8a66597) u16 tmp; int i = 0; -#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) - do { - r8a66597_write(r8a66597, SCKE, SYSCFG0); - tmp = r8a66597_read(r8a66597, SYSCFG0); - if (i++ > 1000) { - printf("register access fail.\n"); - return -1; - } - } while ((tmp & SCKE) != SCKE); - r8a66597_write(r8a66597, 0x04, 0x02); -#else do { r8a66597_write(r8a66597, USBE, SYSCFG0); tmp = r8a66597_read(r8a66597, SYSCFG0); @@ -81,57 +92,30 @@ static int r8a66597_clock_enable(struct r8a66597 *r8a66597) } } while ((tmp & USBE) != USBE); r8a66597_bclr(r8a66597, USBE, SYSCFG0); -#if !defined(CONFIG_RZA_USB) - r8a66597_mdfy(r8a66597, CONFIG_R8A66597_XTAL, XTAL, SYSCFG0); - - i = 0; - r8a66597_bset(r8a66597, XCKE, SYSCFG0); - do { - udelay(1000); - tmp = r8a66597_read(r8a66597, SYSCFG0); - if (i++ > 500) { - printf("register access fail.\n"); - return -1; - } - } while ((tmp & SCKE) != SCKE); -#else /* * RZ/A Only: * Bits XTAL(UCKSEL) and UPLLE in SYSCFG0 for USB0 controls both USB0 * and USB1, so we must always set the USB0 register */ #if (CONFIG_R8A66597_XTAL == 1) - setbits(le16, R8A66597_BASE0, XTAL); + r8a66597_bset(r8a66597, XTAL, SYSCFG0); #endif mdelay(1); - setbits(le16, R8A66597_BASE0, UPLLE); + r8a66597_bset(r8a66597, UPLLE, SYSCFG0); mdelay(1); r8a66597_bset(r8a66597, SUSPM, SUSPMODE0); -#endif /* CONFIG_RZA_USB */ -#endif /* #if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) */ return 0; } static void r8a66597_clock_disable(struct r8a66597 *r8a66597) { -#if !defined(CONFIG_RZA_USB) - r8a66597_bclr(r8a66597, SCKE, SYSCFG0); - udelay(1); -#if !defined(CONFIG_SUPERH_ON_CHIP_R8A66597) - r8a66597_bclr(r8a66597, PLLC, SYSCFG0); - r8a66597_bclr(r8a66597, XCKE, SYSCFG0); - r8a66597_bclr(r8a66597, USBE, SYSCFG0); -#endif -#else r8a66597_bclr(r8a66597, SUSPM, SUSPMODE0); - clrbits(le16, R8A66597_BASE0, UPLLE); + r8a66597_bclr(r8a66597, UPLLE, SYSCFG0); mdelay(1); r8a66597_bclr(r8a66597, USBE, SYSCFG0); mdelay(1); - -#endif } static void r8a66597_enable_port(struct r8a66597 *r8a66597, int port) @@ -141,10 +125,6 @@ static void r8a66597_enable_port(struct r8a66597 *r8a66597, int port) val = port ? DRPD : DCFM | DRPD; r8a66597_bset(r8a66597, val, get_syscfg_reg(port)); r8a66597_bset(r8a66597, HSE, get_syscfg_reg(port)); - -#if !defined(CONFIG_RZA_USB) - r8a66597_write(r8a66597, BURST | CPU_ADR_RD_WR, get_dmacfg_reg(port)); -#endif } static void r8a66597_disable_port(struct r8a66597 *r8a66597, int port) @@ -174,9 +154,6 @@ static int enable_controller(struct r8a66597 *r8a66597) if (ret < 0) return ret; -#if !defined(CONFIG_RZA_USB) - r8a66597_bset(r8a66597, CONFIG_R8A66597_LDRV & LDRV, PINCFG); -#endif r8a66597_bset(r8a66597, USBE, SYSCFG0); r8a66597_bset(r8a66597, INTL, SOFCFG); @@ -184,9 +161,9 @@ static int enable_controller(struct r8a66597 *r8a66597) for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++) r8a66597_write(r8a66597, 0, get_intenb_reg(port)); - r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, CFIFOSEL); - r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, D0FIFOSEL); - r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, D1FIFOSEL); + r8a66597_bclr(r8a66597, BIGEND, CFIFOSEL); + r8a66597_bclr(r8a66597, BIGEND, D0FIFOSEL); + r8a66597_bclr(r8a66597, BIGEND, D1FIFOSEL); r8a66597_bset(r8a66597, TRNENSEL, SOFCFG); for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++) @@ -294,16 +271,13 @@ static int send_setup_packet(struct r8a66597 *r8a66597, struct usb_device *dev, unsigned long setup_addr = USBREQ; u16 intsts1; int timeout = 3000; -#if defined(CONFIG_RZA_USB) u16 dcpctr; -#endif u16 devsel = setup->request == USB_REQ_SET_ADDRESS ? 0 : dev->devnum; r8a66597_write(r8a66597, make_devsel(devsel) | (8 << dev->maxpacketsize), DCPMAXP); r8a66597_write(r8a66597, ~(SIGN | SACK), INTSTS1); -#if defined(CONFIG_RZA_USB) dcpctr = r8a66597_read(r8a66597, DCPCTR); if ((dcpctr & PID) == PID_BUF) { if (readw_poll_timeout(r8a66597->reg + DCPCTR, dcpctr, @@ -312,7 +286,6 @@ static int send_setup_packet(struct r8a66597 *r8a66597, struct usb_device *dev, return -ETIMEDOUT; } } -#endif for (i = 0; i < 4; i++) { r8a66597_write(r8a66597, le16_to_cpu(p[i]), setup_addr); @@ -349,7 +322,7 @@ static int send_bulk_packet(struct r8a66597 *r8a66597, struct usb_device *dev, R8A66597_DPRINT("%s\n", __func__); r8a66597_mdfy(r8a66597, MBW | BULK_OUT_PIPENUM, - MBW | CURPIPE, CFIFOSEL); + MBW | CURPIPE, CFIFOSEL); r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, BULK_OUT_PIPENUM); tmp = r8a66597_read(r8a66597, CFIFOCTR); if ((tmp & FRDY) == 0) { @@ -373,7 +346,7 @@ static int send_bulk_packet(struct r8a66597 *r8a66597, struct usb_device *dev, dev->act_len += size; r8a66597_mdfy(r8a66597, PID_BUF, PID, - get_pipectr_addr(BULK_OUT_PIPENUM)); + get_pipectr_addr(BULK_OUT_PIPENUM)); while (!(r8a66597_read(r8a66597, BEMPSTS) & (1 << BULK_OUT_PIPENUM))) if (ctrlc()) @@ -382,7 +355,7 @@ static int send_bulk_packet(struct r8a66597 *r8a66597, struct usb_device *dev, if (dev->act_len >= transfer_len) r8a66597_mdfy(r8a66597, PID_NAK, PID, - get_pipectr_addr(BULK_OUT_PIPENUM)); + get_pipectr_addr(BULK_OUT_PIPENUM)); return 0; } @@ -403,17 +376,17 @@ static int receive_bulk_packet(struct r8a66597 *r8a66597, /* prepare */ if (dev->act_len == 0) { r8a66597_mdfy(r8a66597, PID_NAK, PID, - get_pipectr_addr(pipenum)); + get_pipectr_addr(pipenum)); r8a66597_write(r8a66597, ~(1 << pipenum), BRDYSTS); r8a66597_write(r8a66597, TRCLR, get_pipetre_addr(pipenum)); r8a66597_write(r8a66597, - (transfer_len + maxpacket - 1) / maxpacket, + (transfer_len + maxpacket - 1) / maxpacket, get_pipetrn_addr(pipenum)); r8a66597_bset(r8a66597, TRENB, get_pipetre_addr(pipenum)); r8a66597_mdfy(r8a66597, PID_BUF, PID, - get_pipectr_addr(pipenum)); + get_pipectr_addr(pipenum)); } r8a66597_mdfy(r8a66597, MBW | pipenum, MBW | CURPIPE, CFIFOSEL); @@ -490,7 +463,7 @@ static int receive_control_packet(struct r8a66597 *r8a66597, } static int send_status_packet(struct r8a66597 *r8a66597, - unsigned long pipe) + unsigned long pipe) { r8a66597_bset(r8a66597, SQSET, DCPCTR); r8a66597_mdfy(r8a66597, PID_NAK, PID, DCPCTR); @@ -581,16 +554,15 @@ static int check_usb_device_connecting(struct r8a66597 *r8a66597) return -1; /* fail */ } -/*-------------------------------------------------------------------------* - * Virtual Root Hub - *-------------------------------------------------------------------------*/ +/* Virtual Root Hub */ #include -static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe, - void *buffer, int transfer_len, struct devrequest *cmd) +static int r8a66597_submit_rh_msg(struct udevice *udev, struct usb_device *dev, + unsigned long pipe, void *buffer, + int transfer_len, struct devrequest *cmd) { - struct r8a66597 *r8a66597 = &gr8a66597; + struct r8a66597 *r8a66597 = dev_get_priv(udev); int leni = transfer_len; int len = 0; int stat = 0; @@ -658,40 +630,40 @@ static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe, } break; case RH_SET_ADDRESS: - gr8a66597.rh_devnum = wValue; + r8a66597->rh_devnum = wValue; break; case RH_GET_DESCRIPTOR: switch ((wValue & 0xff00) >> 8) { case (0x01): /* device descriptor */ len = min_t(unsigned int, - leni, + leni, min_t(unsigned int, - sizeof(root_hub_dev_des), + sizeof(root_hub_dev_des), wLength)); memcpy(buffer, root_hub_dev_des, len); break; case (0x02): /* configuration descriptor */ len = min_t(unsigned int, - leni, + leni, min_t(unsigned int, - sizeof(root_hub_config_des), + sizeof(root_hub_config_des), wLength)); memcpy(buffer, root_hub_config_des, len); break; case (0x03): /* string descriptors */ if (wValue == 0x0300) { len = min_t(unsigned int, - leni, + leni, min_t(unsigned int, - sizeof(root_hub_str_index0), + sizeof(root_hub_str_index0), wLength)); memcpy(buffer, root_hub_str_index0, len); } if (wValue == 0x0301) { len = min_t(unsigned int, - leni, + leni, min_t(unsigned int, - sizeof(root_hub_str_index1), + sizeof(root_hub_str_index1), wLength)); memcpy(buffer, root_hub_str_index1, len); } @@ -724,7 +696,8 @@ static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe, } else { data[0] += 2; data[8] = (temp & RH_B_DR) >> 8; - data[10] = data[9] = 0xff; + data[9] = 0xff; + data[10] = 0xff; } len = min_t(unsigned int, leni, @@ -734,7 +707,7 @@ static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe, } case RH_GET_CONFIGURATION: - *(__u8 *) buffer = 0x01; + *(__u8 *)buffer = 0x01; len = 1; break; case RH_SET_CONFIGURATION: @@ -754,50 +727,22 @@ static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe, return stat; } -int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len) +static int r8a66597_submit_control_msg(struct udevice *udev, + struct usb_device *dev, + unsigned long pipe, void *buffer, + int length, struct devrequest *setup) { - struct r8a66597 *r8a66597 = &gr8a66597; - int ret = 0; - - R8A66597_DPRINT("%s\n", __func__); - R8A66597_DPRINT("pipe = %08x, buffer = %p, len = %d, devnum = %d\n", - pipe, buffer, transfer_len, dev->devnum); - - set_devadd(r8a66597, dev->devnum, dev, 0); - - pipe_buffer_setting(r8a66597, dev, pipe); - - dev->act_len = 0; - while (dev->act_len < transfer_len && ret == 0) { - if (ctrlc()) - return -1; - - if (usb_pipein(pipe)) - ret = receive_bulk_packet(r8a66597, dev, pipe, buffer, - transfer_len); - else - ret = send_bulk_packet(r8a66597, dev, pipe, buffer, - transfer_len); - } - - if (ret == 0) - dev->status = 0; - - return ret; -} - -int submit_control_msg(struct usb_device *dev, unsigned long pipe, - void *buffer, int transfer_len, struct devrequest *setup) -{ - struct r8a66597 *r8a66597 = &gr8a66597; + struct r8a66597 *r8a66597 = dev_get_priv(udev); u16 r8a66597_address = setup->request == USB_REQ_SET_ADDRESS ? 0 : dev->devnum; + debug("%s: dev='%s', udev=%p, udev->dev='%s', portnr=%d\n", __func__, + udev->name, dev, dev->dev->name, dev->portnr); + R8A66597_DPRINT("%s\n", __func__); if (usb_pipedevice(pipe) == r8a66597->rh_devnum) - return r8a66597_submit_rh_msg(dev, pipe, buffer, transfer_len, - setup); + return r8a66597_submit_rh_msg(udev, dev, pipe, buffer, + length, setup); R8A66597_DPRINT("%s: setup\n", __func__); set_devadd(r8a66597, r8a66597_address, dev, 0); @@ -810,7 +755,7 @@ int submit_control_msg(struct usb_device *dev, unsigned long pipe, dev->act_len = 0; if (usb_pipein(pipe)) if (receive_control_packet(r8a66597, dev, buffer, - transfer_len) < 0) + length) < 0) return -1; if (send_status_packet(r8a66597, pipe) < 0) @@ -821,40 +766,131 @@ int submit_control_msg(struct usb_device *dev, unsigned long pipe, return 0; } -int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len, int interval) +static int r8a66597_submit_bulk_msg(struct udevice *udev, + struct usb_device *dev, unsigned long pipe, + void *buffer, int length) { - /* no implement */ + struct r8a66597 *r8a66597 = dev_get_priv(udev); + int ret = 0; + + debug("%s: dev='%s', udev=%p\n", __func__, udev->name, dev); + R8A66597_DPRINT("%s\n", __func__); + R8A66597_DPRINT("pipe = %08x, buffer = %p, len = %d, devnum = %d\n", + pipe, buffer, length, dev->devnum); + + set_devadd(r8a66597, dev->devnum, dev, 0); + + pipe_buffer_setting(r8a66597, dev, pipe); + + dev->act_len = 0; + while (dev->act_len < length && ret == 0) { + if (ctrlc()) + return -1; + + if (usb_pipein(pipe)) + ret = receive_bulk_packet(r8a66597, dev, pipe, buffer, + length); + else + ret = send_bulk_packet(r8a66597, dev, pipe, buffer, + length); + } + + if (ret == 0) + dev->status = 0; + + return ret; +} + +static int r8a66597_usb_ofdata_to_platdata(struct udevice *dev) +{ + struct r8a66597 *priv = dev_get_priv(dev); + fdt_addr_t addr; + + addr = dev_read_addr(dev); + if (addr == FDT_ADDR_T_NONE) + return -EINVAL; + priv->reg = addr; + return 0; } -int usb_lowlevel_init(int index, enum usb_init_type init, void **controller) +static int r8a66597_usb_probe(struct udevice *dev) { - struct r8a66597 *r8a66597 = &gr8a66597; + struct r8a66597 *priv = dev_get_priv(dev); + struct usb_bus_priv *bus_priv = dev_get_uclass_priv(dev); + int ret; - R8A66597_DPRINT("%s\n", __func__); + bus_priv->desc_before_addr = true; - memset(r8a66597, 0, sizeof(*r8a66597)); - r8a66597->reg = CONFIG_R8A66597_BASE_ADDR; + if (CONFIG_IS_ENABLED(DM_REGULATOR)) { + ret = device_get_supply_regulator(dev, "vbus-supply", + &priv->vbus_supply); + if (ret) { + dev_err(dev, + "can't get VBUS supply\n"); + return ret; + } - disable_controller(r8a66597); + ret = regulator_set_enable(priv->vbus_supply, true); + if (ret) { + dev_err(dev, + "can't enable VBUS supply\n"); + return ret; + } + } + + disable_controller(priv); mdelay(100); - enable_controller(r8a66597); - r8a66597_port_power(r8a66597, 0 , 1); + enable_controller(priv); + r8a66597_port_power(priv, 0, 1); /* check usb device */ - check_usb_device_connecting(r8a66597); + check_usb_device_connecting(priv); mdelay(50); return 0; } -int usb_lowlevel_stop(int index) +static int r8a66597_usb_remove(struct udevice *dev) { - disable_controller(&gr8a66597); + struct r8a66597 *priv = dev_get_priv(dev); + int ret; + + disable_controller(priv); + + if (CONFIG_IS_ENABLED(DM_REGULATOR)) { + ret = regulator_set_enable(priv->vbus_supply, false); + if (ret) { + dev_err(dev, + "can't disable VBUS supply\n"); + return ret; + } + } return 0; } + +struct dm_usb_ops r8a66597_usb_ops = { + .control = r8a66597_submit_control_msg, + .bulk = r8a66597_submit_bulk_msg, +}; + +static const struct udevice_id r8a66597_usb_ids[] = { + { .compatible = "renesas,rza1-usbhs" }, + { } +}; + +U_BOOT_DRIVER(usb_r8a66597) = { + .name = "r8a66597_usb", + .id = UCLASS_USB, + .of_match = r8a66597_usb_ids, + .ofdata_to_platdata = r8a66597_usb_ofdata_to_platdata, + .probe = r8a66597_usb_probe, + .remove = r8a66597_usb_remove, + .ops = &r8a66597_usb_ops, + .priv_auto_alloc_size = sizeof(struct r8a66597), + .flags = DM_FLAG_ALLOC_PRIV_DMA, +}; diff --git a/drivers/usb/host/r8a66597.h b/drivers/usb/host/r8a66597.h index ffdb39e8bb..b6110d6b3f 100644 --- a/drivers/usb/host/r8a66597.h +++ b/drivers/usb/host/r8a66597.h @@ -72,9 +72,9 @@ #define PIPE3TRE 0x98 #define PIPE3TRN 0x9A #define PIPE4TRE 0x9C -#define PIPE4TRN 0x9E -#define PIPE5TRE 0xA0 -#define PIPE5TRN 0xA2 +#define PIPE4TRN 0x9E +#define PIPE5TRE 0xA0 +#define PIPE5TRN 0xA2 #define DEVADD0 0xD0 #define DEVADD1 0xD2 #define DEVADD2 0xD4 @@ -89,320 +89,295 @@ #define SUSPMODE0 0x102 /* RZ/A only */ /* System Configuration Control Register */ -#if !defined(CONFIG_RZA_USB) -#define XTAL 0xC000 /* b15-14: Crystal selection */ -#define XTAL48 0x8000 /* 48MHz */ -#define XTAL24 0x4000 /* 24MHz */ -#define XTAL12 0x0000 /* 12MHz */ -#define XCKE 0x2000 /* b13: External clock enable */ -#define PLLC 0x0800 /* b11: PLL control */ -#define SCKE 0x0400 /* b10: USB clock enable */ -#define PCSDIS 0x0200 /* b9: not CS wakeup */ -#define LPSME 0x0100 /* b8: Low power sleep mode */ -#endif -#define HSE 0x0080 /* b7: Hi-speed enable */ -#define DCFM 0x0040 /* b6: Controller function select */ -#define DRPD 0x0020 /* b5: D+/- pull down control */ -#define DPRPU 0x0010 /* b4: D+ pull up control */ -#if defined(CONFIG_RZA_USB) -#define XTAL 0x0004 /* b2: Crystal selection */ -#define XTAL12 0x0004 /* 12MHz */ -#define XTAL48 0x0000 /* 48MHz */ -#define UPLLE 0x0002 /* b1: internal PLL control */ -#endif -#define USBE 0x0001 /* b0: USB module operation enable */ +#define HSE 0x0080 /* b7: Hi-speed enable */ +#define DCFM 0x0040 /* b6: Controller function select */ +#define DRPD 0x0020 /* b5: D+/- pull down control */ +#define DPRPU 0x0010 /* b4: D+ pull up control */ +#define XTAL 0x0004 /* b2: Crystal selection */ +#define XTAL12 0x0004 /* 12MHz */ +#define XTAL48 0x0000 /* 48MHz */ +#define UPLLE 0x0002 /* b1: internal PLL control */ +#define USBE 0x0001 /* b0: USB module operation enable */ /* System Configuration Status Register */ -#define OVCBIT 0x8000 /* b15-14: Over-current bit */ -#define OVCMON 0xC000 /* b15-14: Over-current monitor */ -#define SOFEA 0x0020 /* b5: SOF monitor */ -#define IDMON 0x0004 /* b3: ID-pin monitor */ -#define LNST 0x0003 /* b1-0: D+, D- line status */ -#define SE1 0x0003 /* SE1 */ -#define FS_KSTS 0x0002 /* Full-Speed K State */ -#define FS_JSTS 0x0001 /* Full-Speed J State */ -#define LS_JSTS 0x0002 /* Low-Speed J State */ -#define LS_KSTS 0x0001 /* Low-Speed K State */ -#define SE0 0x0000 /* SE0 */ +#define OVCBIT 0x8000 /* b15-14: Over-current bit */ +#define OVCMON 0xC000 /* b15-14: Over-current monitor */ +#define SOFEA 0x0020 /* b5: SOF monitor */ +#define IDMON 0x0004 /* b3: ID-pin monitor */ +#define LNST 0x0003 /* b1-0: D+, D- line status */ +#define SE1 0x0003 /* SE1 */ +#define FS_KSTS 0x0002 /* Full-Speed K State */ +#define FS_JSTS 0x0001 /* Full-Speed J State */ +#define LS_JSTS 0x0002 /* Low-Speed J State */ +#define LS_KSTS 0x0001 /* Low-Speed K State */ +#define SE0 0x0000 /* SE0 */ /* Device State Control Register */ -#define EXTLP0 0x0400 /* b10: External port */ -#define VBOUT 0x0200 /* b9: VBUS output */ -#define WKUP 0x0100 /* b8: Remote wakeup */ -#define RWUPE 0x0080 /* b7: Remote wakeup sense */ -#define USBRST 0x0040 /* b6: USB reset enable */ -#define RESUME 0x0020 /* b5: Resume enable */ -#define UACT 0x0010 /* b4: USB bus enable */ -#define RHST 0x0007 /* b1-0: Reset handshake status */ -#define HSPROC 0x0004 /* HS handshake is processing */ -#define HSMODE 0x0003 /* Hi-Speed mode */ -#define FSMODE 0x0002 /* Full-Speed mode */ -#define LSMODE 0x0001 /* Low-Speed mode */ -#define UNDECID 0x0000 /* Undecided */ +#define EXTLP0 0x0400 /* b10: External port */ +#define VBOUT 0x0200 /* b9: VBUS output */ +#define WKUP 0x0100 /* b8: Remote wakeup */ +#define RWUPE 0x0080 /* b7: Remote wakeup sense */ +#define USBRST 0x0040 /* b6: USB reset enable */ +#define RESUME 0x0020 /* b5: Resume enable */ +#define UACT 0x0010 /* b4: USB bus enable */ +#define RHST 0x0007 /* b1-0: Reset handshake status */ +#define HSPROC 0x0004 /* HS handshake is processing */ +#define HSMODE 0x0003 /* Hi-Speed mode */ +#define FSMODE 0x0002 /* Full-Speed mode */ +#define LSMODE 0x0001 /* Low-Speed mode */ +#define UNDECID 0x0000 /* Undecided */ /* Test Mode Register */ -#define UTST 0x000F /* b3-0: Test select */ -#define H_TST_PACKET 0x000C /* HOST TEST Packet */ -#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */ -#define H_TST_K 0x000A /* HOST TEST K */ -#define H_TST_J 0x0009 /* HOST TEST J */ -#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */ -#define P_TST_PACKET 0x0004 /* PERI TEST Packet */ -#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */ -#define P_TST_K 0x0002 /* PERI TEST K */ -#define P_TST_J 0x0001 /* PERI TEST J */ -#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */ +#define UTST 0x000F /* b3-0: Test select */ +#define H_TST_PACKET 0x000C /* HOST TEST Packet */ +#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */ +#define H_TST_K 0x000A /* HOST TEST K */ +#define H_TST_J 0x0009 /* HOST TEST J */ +#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */ +#define P_TST_PACKET 0x0004 /* PERI TEST Packet */ +#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */ +#define P_TST_K 0x0002 /* PERI TEST K */ +#define P_TST_J 0x0001 /* PERI TEST J */ +#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */ /* Data Pin Configuration Register */ -#define LDRV 0x8000 /* b15: Drive Current Adjust */ -#define VIF1 0x0000 /* VIF = 1.8V */ -#define VIF3 0x8000 /* VIF = 3.3V */ -#define INTA 0x0001 /* b1: USB INT-pin active */ +#define LDRV 0x8000 /* b15: Drive Current Adjust */ +#define VIF1 0x0000 /* VIF = 1.8V */ +#define VIF3 0x8000 /* VIF = 3.3V */ +#define INTA 0x0001 /* b1: USB INT-pin active */ /* DMAx Pin Configuration Register */ -#define DREQA 0x4000 /* b14: Dreq active select */ -#define BURST 0x2000 /* b13: Burst mode */ -#define DACKA 0x0400 /* b10: Dack active select */ -#define DFORM 0x0380 /* b9-7: DMA mode select */ -#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */ -#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */ -#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */ -#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */ -#define DENDA 0x0040 /* b6: Dend active select */ -#define PKTM 0x0020 /* b5: Packet mode */ -#define DENDE 0x0010 /* b4: Dend enable */ -#define OBUS 0x0004 /* b2: OUTbus mode */ +#define DREQA 0x4000 /* b14: Dreq active select */ +#define BURST 0x2000 /* b13: Burst mode */ +#define DACKA 0x0400 /* b10: Dack active select */ +#define DFORM 0x0380 /* b9-7: DMA mode select */ +#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */ +#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */ +#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */ +#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */ +#define DENDA 0x0040 /* b6: Dend active select */ +#define PKTM 0x0020 /* b5: Packet mode */ +#define DENDE 0x0010 /* b4: Dend enable */ +#define OBUS 0x0004 /* b2: OUTbus mode */ /* CFIFO/DxFIFO Port Select Register */ -#define RCNT 0x8000 /* b15: Read count mode */ -#define REW 0x4000 /* b14: Buffer rewind */ -#define DCLRM 0x2000 /* b13: DMA buffer clear mode */ -#define DREQE 0x1000 /* b12: DREQ output enable */ -#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) -#define MBW 0x0800 -#else -#if !defined(CONFIG_RZA_USB) -#define MBW 0x0400 /* b10: Maximum bit width for FIFO access */ -#else -#define MBW 0x0800 /* b10: Maximum bit width for FIFO access */ -#endif -#endif -#define MBW_8 0x0000 /* 8bit */ -#define MBW_16 0x0400 /* 16bit */ -#define MBW_32 0x0800 /* 32bit */ -#define BIGEND 0x0100 /* b8: Big endian mode */ -#define BYTE_LITTLE 0x0000 /* little dendian */ -#define BYTE_BIG 0x0100 /* big endifan */ -#define ISEL 0x0020 /* b5: DCP FIFO port direction select */ -#define CURPIPE 0x000F /* b2-0: PIPE select */ +#define RCNT 0x8000 /* b15: Read count mode */ +#define REW 0x4000 /* b14: Buffer rewind */ +#define DCLRM 0x2000 /* b13: DMA buffer clear mode */ +#define DREQE 0x1000 /* b12: DREQ output enable */ +#define MBW 0x0800 /* b10: Maximum bit width for FIFO access */ +#define MBW_8 0x0000 /* 8bit */ +#define MBW_16 0x0400 /* 16bit */ +#define MBW_32 0x0800 /* 32bit */ +#define BIGEND 0x0100 /* b8: Big endian mode */ +#define BYTE_LITTLE 0x0000 /* little dendian */ +#define BYTE_BIG 0x0100 /* big endifan */ +#define ISEL 0x0020 /* b5: DCP FIFO port direction select */ +#define CURPIPE 0x000F /* b2-0: PIPE select */ /* CFIFO/DxFIFO Port Control Register */ -#define BVAL 0x8000 /* b15: Buffer valid flag */ -#define BCLR 0x4000 /* b14: Buffer clear */ -#define FRDY 0x2000 /* b13: FIFO ready */ -#define DTLN 0x0FFF /* b11-0: FIFO received data length */ +#define BVAL 0x8000 /* b15: Buffer valid flag */ +#define BCLR 0x4000 /* b14: Buffer clear */ +#define FRDY 0x2000 /* b13: FIFO ready */ +#define DTLN 0x0FFF /* b11-0: FIFO received data length */ /* Interrupt Enable Register 0 */ -#define VBSE 0x8000 /* b15: VBUS interrupt */ -#define RSME 0x4000 /* b14: Resume interrupt */ -#define SOFE 0x2000 /* b13: Frame update interrupt */ -#define DVSE 0x1000 /* b12: Device state transition interrupt */ -#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */ -#define BEMPE 0x0400 /* b10: Buffer empty interrupt */ -#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */ -#define BRDYE 0x0100 /* b8: Buffer ready interrupt */ +#define VBSE 0x8000 /* b15: VBUS interrupt */ +#define RSME 0x4000 /* b14: Resume interrupt */ +#define SOFE 0x2000 /* b13: Frame update interrupt */ +#define DVSE 0x1000 /* b12: Device state transition interrupt */ +#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */ +#define BEMPE 0x0400 /* b10: Buffer empty interrupt */ +#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */ +#define BRDYE 0x0100 /* b8: Buffer ready interrupt */ /* Interrupt Enable Register 1 */ -#define OVRCRE 0x8000 /* b15: Over-current interrupt */ -#define BCHGE 0x4000 /* b14: USB us chenge interrupt */ -#define DTCHE 0x1000 /* b12: Detach sense interrupt */ -#define ATTCHE 0x0800 /* b11: Attach sense interrupt */ -#define EOFERRE 0x0040 /* b6: EOF error interrupt */ -#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */ -#define SACKE 0x0010 /* b4: SETUP ACK interrupt */ +#define OVRCRE 0x8000 /* b15: Over-current interrupt */ +#define BCHGE 0x4000 /* b14: USB us chenge interrupt */ +#define DTCHE 0x1000 /* b12: Detach sense interrupt */ +#define ATTCHE 0x0800 /* b11: Attach sense interrupt */ +#define EOFERRE 0x0040 /* b6: EOF error interrupt */ +#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */ +#define SACKE 0x0010 /* b4: SETUP ACK interrupt */ /* BRDY Interrupt Enable/Status Register */ -#define BRDY9 0x0200 /* b9: PIPE9 */ -#define BRDY8 0x0100 /* b8: PIPE8 */ -#define BRDY7 0x0080 /* b7: PIPE7 */ -#define BRDY6 0x0040 /* b6: PIPE6 */ -#define BRDY5 0x0020 /* b5: PIPE5 */ -#define BRDY4 0x0010 /* b4: PIPE4 */ -#define BRDY3 0x0008 /* b3: PIPE3 */ -#define BRDY2 0x0004 /* b2: PIPE2 */ -#define BRDY1 0x0002 /* b1: PIPE1 */ -#define BRDY0 0x0001 /* b1: PIPE0 */ +#define BRDY9 0x0200 /* b9: PIPE9 */ +#define BRDY8 0x0100 /* b8: PIPE8 */ +#define BRDY7 0x0080 /* b7: PIPE7 */ +#define BRDY6 0x0040 /* b6: PIPE6 */ +#define BRDY5 0x0020 /* b5: PIPE5 */ +#define BRDY4 0x0010 /* b4: PIPE4 */ +#define BRDY3 0x0008 /* b3: PIPE3 */ +#define BRDY2 0x0004 /* b2: PIPE2 */ +#define BRDY1 0x0002 /* b1: PIPE1 */ +#define BRDY0 0x0001 /* b1: PIPE0 */ /* NRDY Interrupt Enable/Status Register */ -#define NRDY9 0x0200 /* b9: PIPE9 */ -#define NRDY8 0x0100 /* b8: PIPE8 */ -#define NRDY7 0x0080 /* b7: PIPE7 */ -#define NRDY6 0x0040 /* b6: PIPE6 */ -#define NRDY5 0x0020 /* b5: PIPE5 */ -#define NRDY4 0x0010 /* b4: PIPE4 */ -#define NRDY3 0x0008 /* b3: PIPE3 */ -#define NRDY2 0x0004 /* b2: PIPE2 */ -#define NRDY1 0x0002 /* b1: PIPE1 */ -#define NRDY0 0x0001 /* b1: PIPE0 */ +#define NRDY9 0x0200 /* b9: PIPE9 */ +#define NRDY8 0x0100 /* b8: PIPE8 */ +#define NRDY7 0x0080 /* b7: PIPE7 */ +#define NRDY6 0x0040 /* b6: PIPE6 */ +#define NRDY5 0x0020 /* b5: PIPE5 */ +#define NRDY4 0x0010 /* b4: PIPE4 */ +#define NRDY3 0x0008 /* b3: PIPE3 */ +#define NRDY2 0x0004 /* b2: PIPE2 */ +#define NRDY1 0x0002 /* b1: PIPE1 */ +#define NRDY0 0x0001 /* b1: PIPE0 */ /* BEMP Interrupt Enable/Status Register */ -#define BEMP9 0x0200 /* b9: PIPE9 */ -#define BEMP8 0x0100 /* b8: PIPE8 */ -#define BEMP7 0x0080 /* b7: PIPE7 */ -#define BEMP6 0x0040 /* b6: PIPE6 */ -#define BEMP5 0x0020 /* b5: PIPE5 */ -#define BEMP4 0x0010 /* b4: PIPE4 */ -#define BEMP3 0x0008 /* b3: PIPE3 */ -#define BEMP2 0x0004 /* b2: PIPE2 */ -#define BEMP1 0x0002 /* b1: PIPE1 */ -#define BEMP0 0x0001 /* b0: PIPE0 */ +#define BEMP9 0x0200 /* b9: PIPE9 */ +#define BEMP8 0x0100 /* b8: PIPE8 */ +#define BEMP7 0x0080 /* b7: PIPE7 */ +#define BEMP6 0x0040 /* b6: PIPE6 */ +#define BEMP5 0x0020 /* b5: PIPE5 */ +#define BEMP4 0x0010 /* b4: PIPE4 */ +#define BEMP3 0x0008 /* b3: PIPE3 */ +#define BEMP2 0x0004 /* b2: PIPE2 */ +#define BEMP1 0x0002 /* b1: PIPE1 */ +#define BEMP0 0x0001 /* b0: PIPE0 */ /* SOF Pin Configuration Register */ -#define TRNENSEL 0x0100 /* b8: Select transaction enable period */ -#define BRDYM 0x0040 /* b6: BRDY clear timing */ -#define INTL 0x0020 /* b5: Interrupt sense select */ -#define EDGESTS 0x0010 /* b4: */ -#define SOFMODE 0x000C /* b3-2: SOF pin select */ -#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */ -#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */ -#define SOF_DISABLE 0x0000 /* SOF OUT Disable */ +#define TRNENSEL 0x0100 /* b8: Select transaction enable period */ +#define BRDYM 0x0040 /* b6: BRDY clear timing */ +#define INTL 0x0020 /* b5: Interrupt sense select */ +#define EDGESTS 0x0010 /* b4: */ +#define SOFMODE 0x000C /* b3-2: SOF pin select */ +#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */ +#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */ +#define SOF_DISABLE 0x0000 /* SOF OUT Disable */ /* Interrupt Status Register 0 */ -#define VBINT 0x8000 /* b15: VBUS interrupt */ -#define RESM 0x4000 /* b14: Resume interrupt */ -#define SOFR 0x2000 /* b13: SOF frame update interrupt */ -#define DVST 0x1000 /* b12: Device state transition interrupt */ -#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */ -#define BEMP 0x0400 /* b10: Buffer empty interrupt */ -#define NRDY 0x0200 /* b9: Buffer not ready interrupt */ -#define BRDY 0x0100 /* b8: Buffer ready interrupt */ -#define VBSTS 0x0080 /* b7: VBUS input port */ -#define DVSQ 0x0070 /* b6-4: Device state */ -#define DS_SPD_CNFG 0x0070 /* Suspend Configured */ -#define DS_SPD_ADDR 0x0060 /* Suspend Address */ -#define DS_SPD_DFLT 0x0050 /* Suspend Default */ -#define DS_SPD_POWR 0x0040 /* Suspend Powered */ -#define DS_SUSP 0x0040 /* Suspend */ -#define DS_CNFG 0x0030 /* Configured */ -#define DS_ADDS 0x0020 /* Address */ -#define DS_DFLT 0x0010 /* Default */ -#define DS_POWR 0x0000 /* Powered */ -#define DVSQS 0x0030 /* b5-4: Device state */ -#define VALID 0x0008 /* b3: Setup packet detected flag */ -#define CTSQ 0x0007 /* b2-0: Control transfer stage */ -#define CS_SQER 0x0006 /* Sequence error */ -#define CS_WRND 0x0005 /* Control write nodata status stage */ -#define CS_WRSS 0x0004 /* Control write status stage */ -#define CS_WRDS 0x0003 /* Control write data stage */ -#define CS_RDSS 0x0002 /* Control read status stage */ -#define CS_RDDS 0x0001 /* Control read data stage */ -#define CS_IDST 0x0000 /* Idle or setup stage */ +#define VBINT 0x8000 /* b15: VBUS interrupt */ +#define RESM 0x4000 /* b14: Resume interrupt */ +#define SOFR 0x2000 /* b13: SOF frame update interrupt */ +#define DVST 0x1000 /* b12: Device state transition interrupt */ +#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */ +#define BEMP 0x0400 /* b10: Buffer empty interrupt */ +#define NRDY 0x0200 /* b9: Buffer not ready interrupt */ +#define BRDY 0x0100 /* b8: Buffer ready interrupt */ +#define VBSTS 0x0080 /* b7: VBUS input port */ +#define DVSQ 0x0070 /* b6-4: Device state */ +#define DS_SPD_CNFG 0x0070 /* Suspend Configured */ +#define DS_SPD_ADDR 0x0060 /* Suspend Address */ +#define DS_SPD_DFLT 0x0050 /* Suspend Default */ +#define DS_SPD_POWR 0x0040 /* Suspend Powered */ +#define DS_SUSP 0x0040 /* Suspend */ +#define DS_CNFG 0x0030 /* Configured */ +#define DS_ADDS 0x0020 /* Address */ +#define DS_DFLT 0x0010 /* Default */ +#define DS_POWR 0x0000 /* Powered */ +#define DVSQS 0x0030 /* b5-4: Device state */ +#define VALID 0x0008 /* b3: Setup packet detected flag */ +#define CTSQ 0x0007 /* b2-0: Control transfer stage */ +#define CS_SQER 0x0006 /* Sequence error */ +#define CS_WRND 0x0005 /* Control write nodata status stage */ +#define CS_WRSS 0x0004 /* Control write status stage */ +#define CS_WRDS 0x0003 /* Control write data stage */ +#define CS_RDSS 0x0002 /* Control read status stage */ +#define CS_RDDS 0x0001 /* Control read data stage */ +#define CS_IDST 0x0000 /* Idle or setup stage */ /* Interrupt Status Register 1 */ -#define OVRCR 0x8000 /* b15: Over-current interrupt */ -#define BCHG 0x4000 /* b14: USB bus chenge interrupt */ -#define DTCH 0x1000 /* b12: Detach sense interrupt */ -#define ATTCH 0x0800 /* b11: Attach sense interrupt */ -#define EOFERR 0x0040 /* b6: EOF-error interrupt */ -#define SIGN 0x0020 /* b5: Setup ignore interrupt */ -#define SACK 0x0010 /* b4: Setup acknowledge interrupt */ +#define OVRCR 0x8000 /* b15: Over-current interrupt */ +#define BCHG 0x4000 /* b14: USB bus chenge interrupt */ +#define DTCH 0x1000 /* b12: Detach sense interrupt */ +#define ATTCH 0x0800 /* b11: Attach sense interrupt */ +#define EOFERR 0x0040 /* b6: EOF-error interrupt */ +#define SIGN 0x0020 /* b5: Setup ignore interrupt */ +#define SACK 0x0010 /* b4: Setup acknowledge interrupt */ /* Frame Number Register */ -#define OVRN 0x8000 /* b15: Overrun error */ -#define CRCE 0x4000 /* b14: Received data error */ -#define FRNM 0x07FF /* b10-0: Frame number */ +#define OVRN 0x8000 /* b15: Overrun error */ +#define CRCE 0x4000 /* b14: Received data error */ +#define FRNM 0x07FF /* b10-0: Frame number */ /* Micro Frame Number Register */ -#define UFRNM 0x0007 /* b2-0: Micro frame number */ +#define UFRNM 0x0007 /* b2-0: Micro frame number */ /* Default Control Pipe Maxpacket Size Register */ /* Pipe Maxpacket Size Register */ -#define DEVSEL 0xF000 /* b15-14: Device address select */ -#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */ +#define DEVSEL 0xF000 /* b15-14: Device address select */ +#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */ /* Default Control Pipe Control Register */ -#define BSTS 0x8000 /* b15: Buffer status */ -#define SUREQ 0x4000 /* b14: Send USB request */ -#define CSCLR 0x2000 /* b13: complete-split status clear */ -#define CSSTS 0x1000 /* b12: complete-split status */ -#define SUREQCLR 0x0800 /* b11: stop setup request */ -#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ -#define SQSET 0x0080 /* b7: Sequence toggle bit set */ -#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ -#define PBUSY 0x0020 /* b5: pipe busy */ -#define PINGE 0x0010 /* b4: ping enable */ -#define CCPL 0x0004 /* b2: Enable control transfer complete */ -#define PID 0x0003 /* b1-0: Response PID */ -#define PID_STALL11 0x0003 /* STALL */ -#define PID_STALL 0x0002 /* STALL */ -#define PID_BUF 0x0001 /* BUF */ -#define PID_NAK 0x0000 /* NAK */ +#define BSTS 0x8000 /* b15: Buffer status */ +#define SUREQ 0x4000 /* b14: Send USB request */ +#define CSCLR 0x2000 /* b13: complete-split status clear */ +#define CSSTS 0x1000 /* b12: complete-split status */ +#define SUREQCLR 0x0800 /* b11: stop setup request */ +#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ +#define SQSET 0x0080 /* b7: Sequence toggle bit set */ +#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ +#define PBUSY 0x0020 /* b5: pipe busy */ +#define PINGE 0x0010 /* b4: ping enable */ +#define CCPL 0x0004 /* b2: Enable control transfer complete */ +#define PID 0x0003 /* b1-0: Response PID */ +#define PID_STALL11 0x0003 /* STALL */ +#define PID_STALL 0x0002 /* STALL */ +#define PID_BUF 0x0001 /* BUF */ +#define PID_NAK 0x0000 /* NAK */ /* Pipe Window Select Register */ -#define PIPENM 0x0007 /* b2-0: Pipe select */ +#define PIPENM 0x0007 /* b2-0: Pipe select */ /* Pipe Configuration Register */ -#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */ -#define R8A66597_ISO 0xC000 /* Isochronous */ -#define R8A66597_INT 0x8000 /* Interrupt */ -#define R8A66597_BULK 0x4000 /* Bulk */ -#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */ -#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */ -#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */ -#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */ -#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */ -#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */ +#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */ +#define R8A66597_ISO 0xC000 /* Isochronous */ +#define R8A66597_INT 0x8000 /* Interrupt */ +#define R8A66597_BULK 0x4000 /* Bulk */ +#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */ +#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */ +#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */ +#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */ +#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */ +#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */ /* Pipe Buffer Configuration Register */ -#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */ -#define BUFNMB 0x007F /* b6-0: Pipe buffer number */ -#define PIPE0BUF 256 -#define PIPExBUF 64 +#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */ +#define BUFNMB 0x007F /* b6-0: Pipe buffer number */ +#define PIPE0BUF 256 +#define PIPExBUF 64 /* Pipe Maxpacket Size Register */ -#define MXPS 0x07FF /* b10-0: Maxpacket size */ +#define MXPS 0x07FF /* b10-0: Maxpacket size */ /* Pipe Cycle Configuration Register */ -#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */ -#define IITV 0x0007 /* b2-0: Isochronous interval */ +#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */ +#define IITV 0x0007 /* b2-0: Isochronous interval */ /* Pipex Control Register */ -#define BSTS 0x8000 /* b15: Buffer status */ -#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */ -#define CSCLR 0x2000 /* b13: complete-split status clear */ -#define CSSTS 0x1000 /* b12: complete-split status */ -#define ATREPM 0x0400 /* b10: Auto repeat mode */ -#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */ -#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ -#define SQSET 0x0080 /* b7: Sequence toggle bit set */ -#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ -#define PBUSY 0x0020 /* b5: pipe busy */ -#define PID 0x0003 /* b1-0: Response PID */ +#define BSTS 0x8000 /* b15: Buffer status */ +#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */ +#define CSCLR 0x2000 /* b13: complete-split status clear */ +#define CSSTS 0x1000 /* b12: complete-split status */ +#define ATREPM 0x0400 /* b10: Auto repeat mode */ +#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */ +#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ +#define SQSET 0x0080 /* b7: Sequence toggle bit set */ +#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ +#define PBUSY 0x0020 /* b5: pipe busy */ +#define PID 0x0003 /* b1-0: Response PID */ /* PIPExTRE */ -#define TRENB 0x0200 /* b9: Transaction counter enable */ -#define TRCLR 0x0100 /* b8: Transaction counter clear */ +#define TRENB 0x0200 /* b9: Transaction counter enable */ +#define TRCLR 0x0100 /* b8: Transaction counter clear */ /* PIPExTRN */ -#define TRNCNT 0xFFFF /* b15-0: Transaction counter */ +#define TRNCNT 0xFFFF /* b15-0: Transaction counter */ /* DEVADDx */ -#define UPPHUB 0x7800 -#define HUBPORT 0x0700 -#define USBSPD 0x00C0 -#define RTPORT 0x0001 +#define UPPHUB 0x7800 +#define HUBPORT 0x0700 +#define USBSPD 0x00C0 +#define RTPORT 0x0001 /* Suspend Mode Register */ -#define SUSPM 0x4000 /* b14: Suspend */ +#define SUSPM 0x4000 /* b14: Suspend */ #define R8A66597_MAX_NUM_PIPE 10 #define R8A66597_BUF_BSIZE 8 #define R8A66597_MAX_DEVICE 10 -#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) -#define R8A66597_MAX_ROOT_HUB 1 -#else #define R8A66597_MAX_ROOT_HUB 2 -#endif #define R8A66597_MAX_SAMPLING 5 #define R8A66597_RH_POLL_TIME 10 @@ -412,9 +387,7 @@ #define BULK_OUT_PIPENUM 4 #define BULK_OUT_BUFNUM 40 -#define check_bulk_or_isoc(pipenum) ((pipenum >= 1 && pipenum <= 5)) -#define check_interrupt(pipenum) ((pipenum >= 6 && pipenum <= 9)) -#define make_devsel(addr) (addr << 12) +#define make_devsel(addr) ((addr) << 12) struct r8a66597 { unsigned long reg; @@ -423,11 +396,12 @@ struct r8a66597 { unsigned short port_change; u16 speed; /* HSMODE or FSMODE or LSMODE */ unsigned char rh_devnum; + struct udevice *vbus_supply; }; static inline u16 r8a66597_read(struct r8a66597 *r8a66597, unsigned long offset) { - return inw(r8a66597->reg + offset); + return readw(r8a66597->reg + offset); } static inline void r8a66597_read_fifo(struct r8a66597 *r8a66597, @@ -435,32 +409,25 @@ static inline void r8a66597_read_fifo(struct r8a66597 *r8a66597, int len) { int i; -#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) || defined(CONFIG_RZA_USB) unsigned long fifoaddr = r8a66597->reg + offset; unsigned long count; unsigned long *p = buf; count = len / 4; for (i = 0; i < count; i++) - p[i] = inl(r8a66597->reg + offset); + p[i] = readl(r8a66597->reg + offset); if (len & 0x00000003) { - unsigned long tmp = inl(fifoaddr); + unsigned long tmp = readl(fifoaddr); + memcpy((unsigned char *)buf + count * 4, &tmp, len & 0x03); } -#else - unsigned short *p = buf; - - len = (len + 1) / 2; - for (i = 0; i < len; i++) - p[i] = inw(r8a66597->reg + offset); -#endif } static inline void r8a66597_write(struct r8a66597 *r8a66597, u16 val, unsigned long offset) { - outw(val, r8a66597->reg + offset); + writew(val, r8a66597->reg + offset); } static inline void r8a66597_write_fifo(struct r8a66597 *r8a66597, @@ -469,43 +436,30 @@ static inline void r8a66597_write_fifo(struct r8a66597 *r8a66597, { int i; unsigned long fifoaddr = r8a66597->reg + offset; -#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) || defined(CONFIG_RZA_USB) unsigned long count; unsigned char *pb; unsigned long *p = buf; count = len / 4; for (i = 0; i < count; i++) - outl(p[i], fifoaddr); + writel(p[i], fifoaddr); if (len & 0x00000003) { pb = (unsigned char *)buf + count * 4; for (i = 0; i < (len & 0x00000003); i++) { if (r8a66597_read(r8a66597, CFIFOSEL) & BIGEND) - outb(pb[i], fifoaddr + i); + writeb(pb[i], fifoaddr + i); else - outb(pb[i], fifoaddr + 3 - i); + writeb(pb[i], fifoaddr + 3 - i); } } -#else - int odd = len & 0x0001; - unsigned short *p = buf; - - len = len / 2; - for (i = 0; i < len; i++) - outw(p[i], fifoaddr); - - if (odd) { - unsigned char *pb = (unsigned char *)(buf + len); - outb(*pb, fifoaddr); - } -#endif } static inline void r8a66597_mdfy(struct r8a66597 *r8a66597, u16 val, u16 pat, unsigned long offset) { u16 tmp; + tmp = r8a66597_read(r8a66597, offset); tmp = tmp & (~pat); tmp = tmp | val; @@ -570,7 +524,6 @@ static inline void r8a66597_port_power(struct r8a66597 *r8a66597, int port, #define get_pipetrn_addr(pipenum) (PIPE1TRN + (pipenum - 1) * 4) #define get_devadd_addr(address) (DEVADD0 + address * 2) - /* USB HUB CONSTANTS (not OHCI-specific; see hub.h, based on usb_ohci.h) */ /* destination of request */ @@ -653,11 +606,11 @@ static inline void r8a66597_port_power(struct r8a66597 *r8a66597, int port, /* roothub.a masks */ #define RH_A_NDP (0xff << 0) /* number of downstream ports */ -#define RH_A_PSM (1 << 8) /* power switching mode */ -#define RH_A_NPS (1 << 9) /* no power switching */ -#define RH_A_DT (1 << 10) /* device type (mbz) */ -#define RH_A_OCPM (1 << 11) /* over current protection mode */ -#define RH_A_NOCP (1 << 12) /* no over current protection */ +#define RH_A_PSM BIT(8) /* power switching mode */ +#define RH_A_NPS BIT(9) /* no power switching */ +#define RH_A_DT BIT(10) /* device type (mbz) */ +#define RH_A_OCPM BIT(11) /* over current protection mode */ +#define RH_A_NOCP BIT(12) /* no over current protection */ #define RH_A_POTPGT (0xff << 24) /* power on to power good time */ #endif /* __R8A66597_H__ */