udoo_neo: Remove USDHC3 support

It's not necessary to support USDHC3 in U-Boot as it's being used for
the WLAN.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit is contained in:
Breno Lima 2016-12-01 16:37:36 -02:00 committed by Stefano Babic
parent a02d517b01
commit c94981efa2
2 changed files with 6 additions and 89 deletions

View File

@ -81,16 +81,6 @@ static iomux_v3_cfg_t const board_recognition_pads[] = {
MX6_PAD_NAND_ALE__GPIO4_IO_0 | BOARD_DETECT_PAD_CFG,
};
static iomux_v3_cfg_t const usdhc3_pads[] = {
/* Configured for WLAN */
MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
static iomux_v3_cfg_t const wdog_b_pad = {
MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
@ -171,91 +161,19 @@ static struct fsl_esdhc_cfg usdhc_cfg[2] = {
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
switch (cfg->esdhc_base) {
case USDHC2_BASE_ADDR:
ret = !gpio_get_value(USDHC2_CD_GPIO);
break;
}
return ret;
return !gpio_get_value(USDHC2_CD_GPIO);
}
int board_mmc_init(bd_t *bis)
{
#ifndef CONFIG_SPL_BUILD
int i, ret;
/*
* According to the board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
* mmc0 USDHC2
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
imx_iomux_v3_setup_multiple_pads(
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
gpio_direction_input(USDHC2_CD_GPIO);
gpio_direction_output(USDHC2_PWR_GPIO, 1);
break;
case 1:
imx_iomux_v3_setup_multiple_pads(
usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
break;
default:
printf("Warning: you configured more USDHC controllers\
(%d) than supported by the board\n", i + 1);
return -EINVAL;
}
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
if (ret) {
printf("Warning:\
failed to initialize mmc dev %d\n", i);
return ret;
}
}
return 0;
#else
struct src *src_regs = (struct src *)SRC_BASE_ADDR;
u32 val;
u32 port;
val = readl(&src_regs->sbmr1);
if ((val & 0xc0) != 0x40) {
printf("Not boot from USDHC!\n");
return -EINVAL;
}
port = (val >> 11) & 0x3;
printf("port %d\n", port);
switch (port) {
case 1:
imx_iomux_v3_setup_multiple_pads(
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
gpio_direction_input(USDHC2_CD_GPIO);
gpio_direction_output(USDHC2_PWR_GPIO, 1);
break;
case 2:
imx_iomux_v3_setup_multiple_pads(
usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
usdhc_cfg[1].esdhc_base = USDHC3_BASE_ADDR;
break;
}
imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
gpio_direction_input(USDHC2_CD_GPIO);
gpio_direction_output(USDHC2_PWR_GPIO, 1);
gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
#endif
}
char *board_string(void)

View File

@ -27,7 +27,6 @@
/* Command definition */
#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_MMC_ENV_DEV 0 /*USDHC2*/
/* Linux only */