mx6: Add board mx6memcal for use in validating DDR

This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.

It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.

When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.

In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.

	https://community.nxp.com/docs/DOC-105652

File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.

Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit is contained in:
Eric Nelson 2017-12-11 13:52:11 -02:00 committed by Stefano Babic
parent 1314bd1192
commit baefb63a13
10 changed files with 894 additions and 0 deletions

View File

@ -210,6 +210,14 @@ config TARGET_MX6LOGICPD
select DM_REGULATOR
select OF_CONTROL
config TARGET_MX6MEMCAL
bool "mx6memcal"
select SUPPORT_SPL
help
The mx6memcal board is a virtual board that can be used to validate
and characterize the memory layout of a new design during the initial
development and pre-production stages.
config TARGET_MX6QARM2
bool "mx6qarm2"
@ -452,6 +460,7 @@ source "board/embest/mx6boards/Kconfig"
source "board/engicam/imx6q/Kconfig"
source "board/engicam/imx6ul/Kconfig"
source "board/freescale/mx6qarm2/Kconfig"
source "board/freescale/mx6memcal/Kconfig"
source "board/freescale/mx6sabreauto/Kconfig"
source "board/freescale/mx6sabresd/Kconfig"
source "board/freescale/mx6slevk/Kconfig"

View File

@ -0,0 +1,235 @@
if TARGET_MX6MEMCAL
config SYS_BOARD
default "mx6memcal"
config SYS_VENDOR
default "freescale"
config SYS_CONFIG_NAME
default "mx6memcal"
menu "mx6memcal specifics"
choice
prompt "Serial console"
help
Either UART1 or UART2 will be used as the console for
displaying the calibration values or errors.
config SERIAL_CONSOLE_UART1
bool "UART1"
help
Select this if your board uses UART1 for its' console.
config SERIAL_CONSOLE_UART2
bool "UART2"
help
Select this if your board uses UART2 for its' console.
endchoice
choice
prompt "UART pads"
help
Select the RX and TX pads used for your serial console.
The choices below reflect the most commonly used options
for your UART.
config UART2_EIM_D26_27
bool "UART2 on EIM_D26/27 (SabreLite, Nitrogen6x)"
depends on SERIAL_CONSOLE_UART2
help
Choose this configuration if you're using pads
EIM_D26 and D27 for a console on UART2.
This is typical for designs that are based on the
NXP SABRELite.
config UART1_CSI0_DAT10_11
bool "UART1 on CSI0_DAT10/11 (Wand)"
depends on SERIAL_CONSOLE_UART1
help
Choose this configuration if you're using pads
CSI0_DAT10 and DAT11 for a console on UART1 as
is done on the i.MX6 Wand board.
config UART1_SD3_DAT6_7
bool "UART1 on SD3_DAT6/7 (SabreSD, SabreAuto)"
depends on SERIAL_CONSOLE_UART1
help
Choose this configuration if you're using pads
SD3_DAT6 and DAT7 for a console on UART1 as is
done on the NXP SABRESD or SABREAUTO designs.
config UART1_UART1
bool "UART1 on UART1 (i.MX6SL EVK, WaRP)"
depends on SERIAL_CONSOLE_UART1
help
Choose this configuration if you're using pads
UART1_TXD/RXD for a console on UART1 as is done
on most i.MX6SL designs.
endchoice
config IMXIMAGE_OUTPUT
bool "Include output for imximage .cfg files"
default y
help
Say "Y" if you want output formatted for use in non-SPL
(DCD-style) configuration files.
config DDRWIDTH
int "DDR bus width"
default 64
help
Select either 32 or 64 to reflect the DDR bus width.
config DDRCS
int "DDR chip selects"
default 2
range 1 2
help
Select the number of chip selects used in your board design
choice
prompt "Memory type"
help
Select the type of DDR (DDR3 or LPDDR2) used on your design
config DDR3
bool "DDR3"
help
Select this if your board design uses DDR3.
config LPDDR2
bool "LPDDR2"
help
Select this if your board design uses LPDDR2.
endchoice
choice
prompt "Memory device"
config MT41K512M16TNA
bool "Micron MT41K512M16TNA 512Mx16 (1GiB/chip)"
depends on DDR3
config MT41K128M16JT
bool "Micron MT41K128M16JT 128Mx16 (256 MiB/chip)"
depends on DDR3
config H5TQ4G63AFR
bool "Hynix H5TQ4G63AFR 256Mx16 (512 MiB/chip)"
depends on DDR3
config H5TQ2G63DFR
bool "Hynix H5TQ2G63DFR 128Mx16 (256 MiB/chip)"
depends on DDR3
config MT42L256M32D2LG
bool "Micron MT42L256M32D2LG LPDDR2 256Mx32 (1GiB/chip)"
depends on LPDDR2
config MT29PZZZ4D4BKESK
bool "Micron MT29PZZZ4D4BKESK multi-chip 512MiB LPDDR2/4GiB eMMC"
depends on LPDDR2
endchoice
config DDR_ODT
int "DDR On-die-termination"
default 2
range 0 7
help
Enter the on-die termination value as an index defined for
IOMUX settings for PAD_DRAM_SDCLK0_P and others.
0 == Disabled
1 == 120 Ohm
2 == 60 Ohm
3 == 40 Ohm
4 == 30 Ohm
5 == 24 Ohm
6 == 20 Ohm
7 == 17 Ohm
Value will be applied to all clock and data lines
config DRAM_DRIVE_STRENGTH
int "DRAM Drive strength"
default 6
range 0 7
help
Enter drive strength as an index defined for IOMUX settings
for GRP_B1DS and others.
0 == Hi Z
6 == 40 Ohm (default)
7 == 34 Ohm
Value will be applied to all clock and data lines
config RTT_NOM
int "RTT_NOM"
default 1
range 1 2
help
Enter the RTT_NOM selector
1 == RZQ/4 (60ohm)
2 == RZQ/2 (120ohm)
config RTT_WR
int "RTT_WR"
default 1
range 0 2
help
Enter the RTT_WR selector for MR2
0 == Dynamic ODT disabled
1 == RZQ/4 (60ohm)
2 == RZQ/2 (120ohm)
config RALAT
int "Read additional latency"
default 5
range 0 7
help
Enter a latency in number of cycles. This will be added to
CAS and internal delays for which the MMDC will retrieve the
read data from the internal FIFO.
This is used to compensate for board/chip delays.
config WALAT
int "Write additional latency"
default 0
range 0 7
help
Enter a latency in number of cycles. This will be added to
CAS and internal delays for which the MMDC will retrieve the
read data from the internal FIFO
This is used to compensate for board/chip delays.
config REFSEL
int "Refresh period"
range 0 3
default 1
help
Select the DDR refresh period.
See the description of bitfield REF_SEL in the reference manual
for details.
0 == disabled
1 == 32 kHz
2 == 64 kHz
3 == fast counter
config REFR
int "Number of refreshes"
range 0 7
default 7
help
This selects the number of refreshes (-1) during each period.
i.e.:
0 == 1 refresh (tRFC)
7 == 8 refreshes (tRFC*8)
See the description of MDREF[REFR] in the reference manual for
details.
endmenu
endif

View File

@ -0,0 +1,7 @@
MX6MEMCAL BOARD
M: Eric Nelson <eric@nelint.com>
S: Maintained
F: board/freescale/mx6memcal/
F: include/configs/mx6memcal.h
F: configs/mx6memcal_defconfig

View File

@ -0,0 +1,13 @@
#
# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
#
# (C) Copyright 2011 Freescale Semiconductor, Inc.
#
# SPDX-License-Identifier: GPL-2.0+
#
ifdef CONFIG_SPL_BUILD
obj-y := spl.o
else
obj-y := mx6memcal.o
endif

View File

@ -0,0 +1,49 @@
mx6memcal - a tool for calibrating DDR on i.MX6 boards.
The mx6memcal board isn't a real board, but a tool for use in bring-up of
new i.MX6 board designs.
It provides a similar function to the tool from NXP([1]) with a number
of advantages:
1. It's open-source, so it's easier to change if needed.
Typical reasons for needing to change include the use of alternate
UARTs and PMIC initialization.
2. It produces an image that's directly loadable with imx_usb [2] or
SB_LOADER.exe [3].
The NXP tool requires either a cumbersome JTAG connection that
makes running the DDR very slow or a working U-Boot image that
suffers from a chicken-and-egg problem (i.e. where do you get the
DDR parameters for U-Boot?).
3. It doesn't prompt for parameters, so it's much faster to gather
data from multiple boards.
4. Parameters to the calibration process can be chosen through
'make menuconfig'.
When booted, the mx6memcal board will run the DDR calibration
routines and display the result in a form suitable for cut and
paste into struct mx6_mmdc_calibration. It can also optionally
produce output in a form usable in a DCD-style .cfg file.
Selections in Kconfig allow most system design settings to be chosen:
1. The UART number and pad configuration for the UART. Options
include support for the most frequent reference designs on
i.MX6DQ/SDL (SABRE Lite and SABRESD designs).
2. The memory bus width (64 and 32-bit)
3. The number of chip-selects in use
4. The type of DDR (DDR3 or LPDDR2). Note that LPDDR2 support
is incomplete as of this writing.
5. The type of DDR chips in use. This selection allows re-use of common
parts and four DDR3 and two LPDDR2 parts are currently defined
6. The On-die termination value for the DRAM lines
7. The DRAM drive strength
8. The RTT_NOM and RTT_WR termination settings
9. RALAT/WALAT latency values
References:
[1] - NXP DDR Stress Test Tool - https://community.nxp.com/docs/DOC-105652
[2] - Boundary Devices imx_usb_loader
https://github.com/boundarydevices/imx_usb_loader
[3] - Use of SB_Loader.exe
https://boundarydevices.com/windows-users-and-unbricking

View File

@ -0,0 +1,32 @@
/*
* mx6memcal board support - provides a minimal, UART-only
* U-Boot that's capable of running a memory test.
*
* Copyright (C) 2016 Nelson Integration, LLC
* Author: Eric Nelson <eric@nelint.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
int board_init(void)
{
return 0;
}
int checkboard(void)
{
puts("Board: mx6memcal\n");
return 0;
}
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}

View File

@ -0,0 +1,456 @@
/*
* Copyright (C) 2016 Nelson Integration, LLC
* Author: Eric Nelson <eric@nelint.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/iomux.h>
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <spl.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
static iomux_v3_cfg_t const uart_pads[] = {
#ifdef CONFIG_UART2_EIM_D26_27
IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
#elif defined(CONFIG_UART1_CSI0_DAT10_11)
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
#elif defined(CONFIG_UART1_SD3_DAT6_7)
IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
#elif defined(CONFIG_UART1_UART1)
MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
#else
#error select UART console pads
#endif
};
#ifdef CONFIG_DDR3
#define GRP_DDRTYPE 0x000C0000
#else
#define GRP_DDRTYPE 0x00080000
#endif
/* all existing designs have this disabled */
#define DDR_PKE 0
/* use Kconfig for ODT and DRIVE_STRENGTH */
#define DDR_ODT \
(CONFIG_DDR_ODT << 8)
#define DRAM_DRIVE_STRENGTH \
(CONFIG_DRAM_DRIVE_STRENGTH << 3)
/* configure MX6Q/DUAL mmdc DDR io registers */
static struct mx6dq_iomux_ddr_regs const mx6dq_ddr_ioregs = {
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
.dram_sdclk_0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_sdclk_1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_cas = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_ras = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_reset = DDR_ODT + DRAM_DRIVE_STRENGTH,
/* SDCKE[0:1]: 100k pull-up */
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
/* SDBA2: pull-up disabled */
.dram_sdba2 = 0x00000000,
/* SDODT[0:1]: 100k pull-up, 40 ohm */
.dram_sdodt0 = 0x00003000 + DRAM_DRIVE_STRENGTH,
.dram_sdodt1 = 0x00003000 + DRAM_DRIVE_STRENGTH,
/* SDQS[0:7]: Differential input, 40 ohm */
.dram_sdqs0 = DRAM_DRIVE_STRENGTH,
.dram_sdqs1 = DRAM_DRIVE_STRENGTH,
.dram_sdqs2 = DRAM_DRIVE_STRENGTH,
.dram_sdqs3 = DRAM_DRIVE_STRENGTH,
.dram_sdqs4 = DRAM_DRIVE_STRENGTH,
.dram_sdqs5 = DRAM_DRIVE_STRENGTH,
.dram_sdqs6 = DRAM_DRIVE_STRENGTH,
.dram_sdqs7 = DRAM_DRIVE_STRENGTH,
/* DQM[0:7]: Differential input, 40 ohm */
.dram_dqm0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm2 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm3 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm4 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm5 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm6 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm7 = DDR_ODT + DRAM_DRIVE_STRENGTH,
};
/* configure MX6Q/DUAL mmdc GRP io registers */
static struct mx6dq_iomux_grp_regs const mx6dq_grp_ioregs = {
/* DDR3 */
.grp_ddr_type = GRP_DDRTYPE,
.grp_ddrmode_ctl = DDR_ODT,
/* disable DDR pullups */
.grp_ddrpke = DDR_PKE,
/* ADDR[00:16], SDBA[0:1]: 40 ohm */
.grp_addds = DRAM_DRIVE_STRENGTH,
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
.grp_ctlds = DRAM_DRIVE_STRENGTH,
/* DATA[00:63]: Differential input, 40 ohm */
.grp_ddrmode = DDR_ODT,
.grp_b0ds = DRAM_DRIVE_STRENGTH,
.grp_b1ds = DRAM_DRIVE_STRENGTH,
.grp_b2ds = DRAM_DRIVE_STRENGTH,
.grp_b3ds = DRAM_DRIVE_STRENGTH,
.grp_b4ds = DRAM_DRIVE_STRENGTH,
.grp_b5ds = DRAM_DRIVE_STRENGTH,
.grp_b6ds = DRAM_DRIVE_STRENGTH,
.grp_b7ds = DRAM_DRIVE_STRENGTH,
};
static struct mx6sdl_iomux_ddr_regs const mx6sdl_ddr_ioregs = {
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
.dram_sdclk_0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_sdclk_1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_cas = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_ras = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_reset = DDR_ODT + DRAM_DRIVE_STRENGTH,
/* SDCKE[0:1]: 100k pull-up */
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
/* SDBA2: pull-up disabled */
.dram_sdba2 = 0x00000000,
/* SDODT[0:1]: 100k pull-up, 40 ohm */
.dram_sdodt0 = 0x00003000 + DRAM_DRIVE_STRENGTH,
.dram_sdodt1 = 0x00003000 + DRAM_DRIVE_STRENGTH,
/* SDQS[0:7]: Differential input, 40 ohm */
.dram_sdqs0 = DRAM_DRIVE_STRENGTH,
.dram_sdqs1 = DRAM_DRIVE_STRENGTH,
.dram_sdqs2 = DRAM_DRIVE_STRENGTH,
.dram_sdqs3 = DRAM_DRIVE_STRENGTH,
.dram_sdqs4 = DRAM_DRIVE_STRENGTH,
.dram_sdqs5 = DRAM_DRIVE_STRENGTH,
.dram_sdqs6 = DRAM_DRIVE_STRENGTH,
.dram_sdqs7 = DRAM_DRIVE_STRENGTH,
/* DQM[0:7]: Differential input, 40 ohm */
.dram_dqm0 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm1 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm2 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm3 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm4 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm5 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm6 = DDR_ODT + DRAM_DRIVE_STRENGTH,
.dram_dqm7 = DDR_ODT + DRAM_DRIVE_STRENGTH,
};
/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
static struct mx6sdl_iomux_grp_regs const mx6sdl_grp_ioregs = {
/* DDR3 */
.grp_ddr_type = GRP_DDRTYPE,
/* SDQS[0:7]: Differential input, 40 ohm */
.grp_ddrmode_ctl = DDR_ODT,
/* disable DDR pullups */
.grp_ddrpke = DDR_PKE,
/* ADDR[00:16], SDBA[0:1]: 40 ohm */
.grp_addds = DRAM_DRIVE_STRENGTH,
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
.grp_ctlds = DRAM_DRIVE_STRENGTH,
/* DATA[00:63]: Differential input, 40 ohm */
.grp_ddrmode = DDR_ODT,
.grp_b0ds = DRAM_DRIVE_STRENGTH,
.grp_b1ds = DRAM_DRIVE_STRENGTH,
.grp_b2ds = DRAM_DRIVE_STRENGTH,
.grp_b3ds = DRAM_DRIVE_STRENGTH,
.grp_b4ds = DRAM_DRIVE_STRENGTH,
.grp_b5ds = DRAM_DRIVE_STRENGTH,
.grp_b6ds = DRAM_DRIVE_STRENGTH,
.grp_b7ds = DRAM_DRIVE_STRENGTH,
};
const struct mx6sl_iomux_ddr_regs mx6sl_ddr_ioregs = {
.dram_sdqs0 = DRAM_DRIVE_STRENGTH,
.dram_sdqs1 = DRAM_DRIVE_STRENGTH,
.dram_sdqs2 = DRAM_DRIVE_STRENGTH,
.dram_sdqs3 = DRAM_DRIVE_STRENGTH,
.dram_dqm0 = DRAM_DRIVE_STRENGTH,
.dram_dqm1 = DRAM_DRIVE_STRENGTH,
.dram_dqm2 = DRAM_DRIVE_STRENGTH,
.dram_dqm3 = DRAM_DRIVE_STRENGTH,
.dram_cas = DRAM_DRIVE_STRENGTH,
.dram_ras = DRAM_DRIVE_STRENGTH,
.dram_sdclk_0 = DRAM_DRIVE_STRENGTH,
.dram_reset = DRAM_DRIVE_STRENGTH,
.dram_sdba2 = 0x00020000,
.dram_odt0 = 0x00030000 + DRAM_DRIVE_STRENGTH,
.dram_odt1 = 0x00030000 + DRAM_DRIVE_STRENGTH,
};
const struct mx6sl_iomux_grp_regs mx6sl_grp_ioregs = {
.grp_b0ds = DRAM_DRIVE_STRENGTH,
.grp_b1ds = DRAM_DRIVE_STRENGTH,
.grp_b2ds = DRAM_DRIVE_STRENGTH,
.grp_b3ds = DRAM_DRIVE_STRENGTH,
.grp_addds = DRAM_DRIVE_STRENGTH,
.grp_ctlds = DRAM_DRIVE_STRENGTH,
.grp_ddrmode_ctl = DDR_ODT,
.grp_ddrpke = DDR_PKE,
.grp_ddrmode = DDR_ODT,
.grp_ddr_type = GRP_DDRTYPE,
};
static struct mx6_ddr_sysinfo const sysinfo = {
/* width of data bus:0=16,1=32,2=64 */
#if CONFIG_DDRWIDTH == 32
.dsize = 1,
#elif CONFIG_DDRWIDTH == 64
.dsize = 2,
#else
#error missing CONFIG_DDRWIDTH
#endif
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
/* # of chip selects */
.ncs = CONFIG_DDRCS,
.cs1_mirror = 0,
.bi_on = 1, /* Bank interleaving enabled */
.rtt_nom = CONFIG_RTT_NOM,
.rtt_wr = CONFIG_RTT_WR,
.ralat = CONFIG_RALAT, /* Read additional latency */
.walat = CONFIG_WALAT, /* Write additional latency */
.mif3_mode = 3, /* Command prediction working mode */
#ifdef CONFIG_DDR3
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.sde_to_rst = 0x10, /* JEDEC value for LPDDR2 - 200us */
.pd_fast_exit = 0, /* immaterial for calibration */
.ddr_type = DDR_TYPE_DDR3,
#else
.rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */
.sde_to_rst = 0, /* LPDDR2 does not need this field */
.pd_fast_exit = 0, /* immaterial for calibration */
.ddr_type = DDR_TYPE_LPDDR2,
#endif
.refsel = CONFIG_REFSEL,
.refr = CONFIG_REFR,
};
#ifdef CONFIG_MT41K512M16TNA
/* Micron MT41K512M16TNA-125 */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1600,
.density = 8,
.width = 16,
.banks = 8,
.rowaddr = 15,
.coladdr = 10,
.pagesz = 1,
.trcd = 1375,
.trcmin = 5062,
.trasmin = 3750,
};
#elif defined(CONFIG_MT41K128M16JT)
/* Micron MT41K128M16JT-125 */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1600,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
#elif defined(CONFIG_H5TQ4G63AFR)
/* Hynix H5TQ4G63AFR */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1600,
.density = 4,
.width = 16,
.banks = 8,
.rowaddr = 15,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
#elif defined CONFIG_H5TQ2G63DFR
/* Hynix H5TQ2G63DFR */
static struct mx6_ddr3_cfg const ddrtype = {
.mem_speed = 1333,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1350,
.trcmin = 4950,
.trasmin = 3600,
};
#elif defined(CONFIG_MT42L256M32D2LG)
/* Micron MT42L256M32D2LG */
static struct mx6_lpddr2_cfg ddrtype = {
.mem_speed = 800,
.density = 4,
.width = 32,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.trcd_lp = 2000,
.trppb_lp = 2000,
.trpab_lp = 2250,
.trasmin = 4200,
};
#elif defined(CONFIG_MT29PZZZ4D4BKESK)
/* Micron MT29PZZZ4D4BKESK */
static struct mx6_lpddr2_cfg ddrtype = {
.mem_speed = 800,
.density = 4,
.width = 32,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.trcd_lp = 2000,
.trppb_lp = 2000,
.trpab_lp = 2250,
.trasmin = 4200,
};
#else
#error please select DDR type using menuconfig
#endif
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* FIXME: these should probably be checked, especially
* for i.MX6SL, UL, ULL
*/
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0x00FFF300, &ccm->CCGR4);
writel(0x0F0000C3, &ccm->CCGR5);
writel(0x000003FF, &ccm->CCGR6);
}
static void display_calibration(struct mx6_mmdc_calibration *calib)
{
printf(".p0_mpdgctrl0\t= 0x%08X\n", calib->p0_mpdgctrl0);
printf(".p0_mpdgctrl1\t= 0x%08X\n", calib->p0_mpdgctrl1);
printf(".p0_mprddlctl\t= 0x%08X\n", calib->p0_mprddlctl);
printf(".p0_mpwrdlctl\t= 0x%08X\n", calib->p0_mpwrdlctl);
printf(".p0_mpwldectrl0\t= 0x%08X\n", calib->p0_mpwldectrl0);
printf(".p0_mpwldectrl1\t= 0x%08X\n", calib->p0_mpwldectrl1);
if (sysinfo.dsize == 2) {
printf(".p1_mpdgctrl0\t= 0x%08X\n", calib->p1_mpdgctrl0);
printf(".p1_mpdgctrl1\t= 0x%08X\n", calib->p1_mpdgctrl1);
printf(".p1_mprddlctl\t= 0x%08X\n", calib->p1_mprddlctl);
printf(".p1_mpwrdlctl\t= 0x%08X\n", calib->p1_mpwrdlctl);
printf(".p1_mpwldectrl0\t= 0x%08X\n", calib->p1_mpwldectrl0);
printf(".p1_mpwldectrl1\t= 0x%08X\n", calib->p1_mpwldectrl1);
}
#ifdef CONFIG_IMXIMAGE_OUTPUT
printf("DATA 4 MX6_MMDC_P0_MPDGCTRL0\t= 0x%08X\n", calib->p0_mpdgctrl0);
printf("DATA 4 MX6_MMDC_P0_MPDGCTRL1\t= 0x%08X\n", calib->p0_mpdgctrl1);
printf("DATA 4 MX6_MMDC_P0_MPRDDLCTL\t= 0x%08X\n", calib->p0_mprddlctl);
printf("DATA 4 MX6_MMDC_P0_MPWRDLCTL\t= 0x%08X\n", calib->p0_mpwrdlctl);
printf("DATA 4 MX6_MMDC_P0_MPWLDECTRL0\t= 0x%08X\n",
calib->p0_mpwldectrl0);
printf("DATA 4 MX6_MMDC_P0_MPWLDECTRL1\t= 0x%08X\n",
calib->p0_mpwldectrl1);
if (sysinfo.dsize == 2) {
printf("DATA 4 MX6_MMDC_P1_MPDGCTRL0\t= 0x%08X\n",
calib->p1_mpdgctrl0);
printf("DATA 4 MX6_MMDC_P1_MPDGCTRL1\t= 0x%08X\n",
calib->p1_mpdgctrl1);
printf("DATA 4 MX6_MMDC_P1_MPRDDLCTL\t= 0x%08X\n",
calib->p1_mprddlctl);
printf("DATA 4 MX6_MMDC_P1_MPWRDLCTL\t= 0x%08X\n",
calib->p1_mpwrdlctl);
printf("DATA 4 MX6_MMDC_P1_MPWLDECTRL0\t= 0x%08X\n",
calib->p1_mpwldectrl0);
printf("DATA 4 MX6_MMDC_P1_MPWLDECTRL1\t= 0x%08X\n",
calib->p1_mpwldectrl1);
}
#endif
}
/*
* called from C runtime startup code (arch/arm/lib/crt0.S:_main)
* - we have a stack and a place to store GD, both in SRAM
* - no variable global data is available
*/
void board_init_f(ulong dummy)
{
int errs;
struct mx6_mmdc_calibration calibration = {0};
memset((void *)gd, 0, sizeof(struct global_data));
/* write leveling calibration defaults */
calibration.p0_mpwrdlctl = 0x40404040;
calibration.p1_mpwrdlctl = 0x40404040;
/* setup AIPS and disable watchdog */
arch_cpu_init();
ccgr_init();
SETUP_IOMUX_PADS(uart_pads);
/* setup GP timer */
timer_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
if (sysinfo.dsize != 1) {
if (is_cpu_type(MXC_CPU_MX6SX) ||
is_cpu_type(MXC_CPU_MX6UL) ||
is_cpu_type(MXC_CPU_MX6SL)) {
printf("cpu type 0x%x doesn't support 64-bit bus\n",
get_cpu_type());
reset_cpu(0);
}
}
#ifdef CONFIG_MX6SL
mx6sl_dram_iocfg(CONFIG_DDRWIDTH, &mx6sl_ddr_ioregs,
&mx6sl_grp_ioregs);
#else
if (is_cpu_type(MXC_CPU_MX6Q)) {
mx6dq_dram_iocfg(CONFIG_DDRWIDTH, &mx6dq_ddr_ioregs,
&mx6dq_grp_ioregs);
} else {
mx6sdl_dram_iocfg(CONFIG_DDRWIDTH, &mx6sdl_ddr_ioregs,
&mx6sdl_grp_ioregs);
}
#endif
mx6_dram_cfg(&sysinfo, &calibration, &ddrtype);
errs = mmdc_do_write_level_calibration(&sysinfo);
if (errs) {
printf("error %d from write level calibration\n", errs);
} else {
errs = mmdc_do_dqs_calibration(&sysinfo);
if (errs) {
printf("error %d from write level calibration\n", errs);
} else {
printf("completed successfully\n");
mmdc_read_calibration(&sysinfo, &calibration);
display_calibration(&calibration);
}
}
reset_cpu(0);
}

View File

@ -0,0 +1,33 @@
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_MX6_DDRCAL=y
CONFIG_TARGET_MX6MEMCAL=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,SPL,MX6QDL"
CONFIG_SPL=y
CONFIG_HUSH_PARSER=y
# CONFIG_MMC is not set
# CONFIG_CMD_BOOTD is not set
# CONFIG_CMD_BOOTM is not set
# CONFIG_CMD_ELF is not set
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_XIMG is not set
# CONFIG_CMD_EXPORTENV is not set
# CONFIG_CMD_IMPORTENV is not set
# CONFIG_CMD_EDITENV is not set
# CONFIG_CMD_SAVEENV is not set
# CONFIG_CMD_ENV_EXISTS is not set
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MEMINFO=y
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
CONFIG_CMD_CACHE=y
CONFIG_REGEX=y

View File

@ -0,0 +1,59 @@
/*
* Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
*
* Configuration settings for the Boundary Devices Nitrogen6X
* and Freescale i.MX6Q Sabre Lite boards.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* SPL */
#include "mx6_common.h"
#include "imx6_spl.h"
#undef CONFIG_FSL_ESDHC
#undef CONFIG_MMC
#undef CONFIG_SPL_MMC_SUPPORT
#undef CONFIG_GENERIC_MMC
#undef CONFIG_CMD_FUSE
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END 0x20000000
#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
#define CONFIG_MXC_UART
#ifdef CONFIG_SERIAL_CONSOLE_UART1
#if defined(CONFIG_MX6SL)
#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
#else
#define CONFIG_MXC_UART_BASE UART1_BASE
#endif
#elif defined(CONFIG_SERIAL_CONSOLE_UART2)
#define CONFIG_MXC_UART_BASE UART2_BASE
#else
#error please define serial console (CONFIG_SERIAL_CONSOLE_UARTx)
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + 16)
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_ENV_SIZE (8 * 1024)
#endif /* __CONFIG_H */

View File

@ -362,6 +362,7 @@ CONFIG_DB_784MP_GP
CONFIG_DCACHE
CONFIG_DCACHE_OFF
CONFIG_DCFG_ADDR
CONFIG_DDR3
CONFIG_DDR_
CONFIG_DDR_2HCLK
CONFIG_DDR_2T_TIMING