diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 5903c09370..fbe90875ae 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1326,6 +1326,18 @@ config TARGET_LX2160AQDS is a high-performance development platform that supports the QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor. +config TARGET_LX2162AQDS + bool "Support lx2162aqds" + select ARCH_LX2162A + select ARCH_MISC_INIT + select ARM64 + select ARMV8_MULTIENTRY + select ARCH_SUPPORT_TFABOOT + select BOARD_LATE_INIT + help + Support for NXP LX2162AQDS platform. + The lx2162aqds support is based on LX2160A Layerscape Architecture processor. + config TARGET_HIKEY bool "Support HiKey 96boards Consumer Edition Platform" select ARM64 diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 02d04f5a8c..fd47e408f8 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -414,7 +414,11 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-lx2160a-qds-19-x-x.dtb \ fsl-lx2160a-qds-19-11-x.dtb \ fsl-lx2160a-qds-20-x-x.dtb \ - fsl-lx2160a-qds-20-11-x.dtb + fsl-lx2160a-qds-20-11-x.dtb \ + fsl-lx2162a-qds.dtb\ + fsl-lx2162a-qds-17-x.dtb\ + fsl-lx2162a-qds-18-x.dtb\ + fsl-lx2162a-qds-20-x.dtb dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \ fsl-ls1043a-qds-lpuart.dtb \ fsl-ls1043a-rdb.dtb \ diff --git a/arch/arm/dts/fsl-lx2160a-qds.dts b/arch/arm/dts/fsl-lx2160a-qds.dts index e0f5d5e2d3..332c778d3a 100644 --- a/arch/arm/dts/fsl-lx2160a-qds.dts +++ b/arch/arm/dts/fsl-lx2160a-qds.dts @@ -13,7 +13,4 @@ / { model = "NXP Layerscape LX2160AQDS Board"; compatible = "fsl,lx2160aqds", "fsl,lx2160a"; - aliases { - spi0 = &fspi; - }; }; diff --git a/arch/arm/dts/fsl-lx2160a-qds.dtsi b/arch/arm/dts/fsl-lx2160a-qds.dtsi index 96c980004b..288607c034 100644 --- a/arch/arm/dts/fsl-lx2160a-qds.dtsi +++ b/arch/arm/dts/fsl-lx2160a-qds.dtsi @@ -2,12 +2,18 @@ /* * NXP LX2160AQDS common device tree source * - * Copyright 2018-2019 NXP + * Copyright 2018-2020 NXP * */ #include "fsl-lx2160a.dtsi" +/ { + aliases { + spi0 = &fspi; + }; +}; + &dpmac17 { status = "okay"; phy-handle = <&rgmii_phy1>; @@ -251,6 +257,20 @@ }; }; +&fspi { + status = "okay"; + + mt35xu512aba0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + spi-rx-bus-width = <8>; + spi-tx-bus-width = <1>; + }; +}; + &sata0 { status = "okay"; }; diff --git a/arch/arm/dts/fsl-lx2162a-qds-17-x.dts b/arch/arm/dts/fsl-lx2162a-qds-17-x.dts new file mode 100644 index 0000000000..8a8895f023 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-17-x.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for SERDES protocol 17.x + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2162a-qds-sd1-17.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board (DTS 17.x)"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-18-x.dts b/arch/arm/dts/fsl-lx2162a-qds-18-x.dts new file mode 100644 index 0000000000..c28e5e2497 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-18-x.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for SERDES protocol 18.x + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2162a-qds-sd1-18.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board (DTS 18.x)"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-20-x.dts b/arch/arm/dts/fsl-lx2162a-qds-20-x.dts new file mode 100644 index 0000000000..7882c767e2 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-20-x.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for SERDES protocol 20.x + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2162a-qds-sd1-20.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board (DTS 20.x)"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi new file mode 100644 index 0000000000..60f5a4ee43 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi @@ -0,0 +1,58 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for the SERDES block #1 - protocol 17 + * + * Some assumptions are made: + * * mezzanine card M8 is connected to IO SLOT1 (25g-aui for DPMAC 3,4,5,6) + * + * Copyright 2020 NXP + * + */ + +#include "fsl-lx2160a-qds.dtsi" + +&dpmac3 { + status = "okay"; + phy-handle = <&inphi_phy0>; + phy-connection-type = "25g-aui"; +}; + +&dpmac4 { + status = "okay"; + phy-handle = <&inphi_phy1>; + phy-connection-type = "25g-aui"; +}; + +&dpmac5 { + status = "okay"; + phy-handle = <&inphi_phy2>; + phy-connection-type = "25g-aui"; +}; + +&dpmac6 { + status = "okay"; + phy-handle = <&inphi_phy3>; + phy-connection-type = "25g-aui"; +}; + +&emdio1_slot1 { + inphi_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x0>; + }; + + inphi_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x1>; + }; + + inphi_phy2: ethernet-phy@2 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x2>; + }; + + inphi_phy3: ethernet-phy@3 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x3>; + }; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi new file mode 100644 index 0000000000..8e11b0680a --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for the SERDES block #1 - protocol 18 + * + * Some assumptions are made: + * * mezzanine card M11 is connected to IO SLOT1 (usxgmii for DPMAC 3,4) + * * mezzanine card M13/M8 is connected to IO SLOT6 (25g-aui for DPMAC 5,6) + * + * Copyright 2020 NXP + * + */ + +#include "fsl-lx2160a-qds.dtsi" + +&dpmac3 { + status = "okay"; + phy-handle = <&aquantia_phy1>; + phy-connection-type = "usxgmii"; +}; + +&dpmac4 { + status = "okay"; + phy-handle = <&aquantia_phy2>; + phy-connection-type = "usxgmii"; +}; + +&dpmac5 { + status = "okay"; + phy-handle = <&inphi_phy0>; + phy-connection-type = "25g-aui"; +}; + +&dpmac6 { + status = "okay"; + phy-handle = <&inphi_phy1>; + phy-connection-type = "25g-aui"; +}; + +&emdio1_slot1 { + aquantia_phy1: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x0>; + }; + + aquantia_phy2: ethernet-phy@5 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x1>; + }; +}; + +&emdio1_slot6 { + inphi_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x0>; + }; + + inphi_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x1>; + }; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi new file mode 100644 index 0000000000..faf4285eab --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for the SERDES block #1 - protocol 20 + * + * Some assumptions are made: + * * Mezzanine card M8 is connected to IO SLOT1 + * (xlaui4 for DPMAC 1) + * + * Copyright 2020 NXP + * + */ + +#include "fsl-lx2160a-qds.dtsi" + +&dpmac1 { + status = "okay"; + phy-handle = <&cortina_phy1_0>; + phy-connection-type = "xlaui4"; +}; + +&emdio1_slot1 { + cortina_phy1_0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x0>; + }; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds.dts b/arch/arm/dts/fsl-lx2162a-qds.dts new file mode 100644 index 0000000000..b16526503d --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds.dts @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2160a-qds.dtsi" + +/ { + model = "NXP Layerscape LX2162AQDS Board"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + + aliases { + pcie@3500000 { + status = "disabled"; + }; + + pcie@3800000 { + status = "disabled"; + }; + + pcie@3900000 { + status = "disabled"; + }; + }; +}; + +&usb1 { + status = "disabled"; +}; diff --git a/board/freescale/common/qixis.h b/board/freescale/common/qixis.h index 93638d2452..0860bd2312 100644 --- a/board/freescale/common/qixis.h +++ b/board/freescale/common/qixis.h @@ -141,4 +141,29 @@ void qixis_write_i2c(unsigned int reg, u8 value); #define QIXIS_EVDD_BY_SDHC_VS 0x0c +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) || \ +defined(CONFIG_TARGET_LX2160ARDB) +#define QIXIS_XMAP_MASK 0x07 +#define QIXIS_RST_CTL_RESET_EN 0x30 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x20 +#define QIXIS_LBMAP_QSPI 0x00 +#define QIXIS_RCW_SRC_QSPI 0xff +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SD +#define QIXIS_LBMAP_EMMC +#define QIXIS_RCW_SRC_SD 0x08 +#define QIXIS_RCW_SRC_EMMC 0x09 +#define NON_EXTENDED_DUTCFG +#endif + +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) +#define QIXIS_SDID_MASK 0x07 +#define QIXIS_ESDHC_NO_ADAPTER 0x7 +#endif + #endif diff --git a/board/freescale/common/vid.h b/board/freescale/common/vid.h index 65b348ee42..5bbaecace4 100644 --- a/board/freescale/common/vid.h +++ b/board/freescale/common/vid.h @@ -1,6 +1,7 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2020 NXP */ #ifndef __VID_H_ @@ -37,6 +38,35 @@ */ #define EN_WRITE_ALL_CMD (0) +#ifdef CONFIG_TARGET_LX2160ARDB +/* The lowest and highest voltage allowed*/ +#define VDD_MV_MIN 775 +#define VDD_MV_MAX 855 +#endif + +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) +/* The lowest and highest voltage allowed*/ +#define VDD_MV_MIN 775 +#define VDD_MV_MAX 925 +#endif + +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) || \ +defined(CONFIG_TARGET_LX2160ARDB) +/* PM Bus commands code for LTC3882*/ +#define PWM_CHANNEL0 0x0 +#define PMBUS_CMD_PAGE 0x0 +#define PMBUS_CMD_READ_VOUT 0x8B +#define PMBUS_CMD_VOUT_COMMAND 0x21 +#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 + +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 +#define I2C_VOL_MONITOR_ADDR 0x63 +#define I2C_MUX_CH_VOL_MONITOR 0xA +#endif + int adjust_vdd(ulong vdd_override); #endif /* __VID_H_ */ diff --git a/board/freescale/lx2160a/Kconfig b/board/freescale/lx2160a/Kconfig index 122a385100..7556f7dd21 100644 --- a/board/freescale/lx2160a/Kconfig +++ b/board/freescale/lx2160a/Kconfig @@ -32,3 +32,19 @@ config SYS_CONFIG_NAME source "board/freescale/common/Kconfig" endif +if TARGET_LX2162AQDS + +config SYS_BOARD + default "lx2160a" + +config SYS_VENDOR + default "freescale" + +config SYS_SOC + default "fsl-layerscape" + +config SYS_CONFIG_NAME + default "lx2162aqds" + +source "board/freescale/common/Kconfig" +endif diff --git a/board/freescale/lx2160a/MAINTAINERS b/board/freescale/lx2160a/MAINTAINERS index 9fe79c0ef7..c627417cf7 100644 --- a/board/freescale/lx2160a/MAINTAINERS +++ b/board/freescale/lx2160a/MAINTAINERS @@ -1,4 +1,5 @@ LX2160ARDB BOARD +M: Meenakshi Aggarwal M: Priyanka Jain S: Maintained F: board/freescale/lx2160a/ @@ -14,6 +15,7 @@ S: Maintained F: configs/lx2160ardb_tfa_SECURE_BOOT_defconfig LX2160AQDS BOARD +M: Meenakshi Aggarwal M: Pankaj Bansal S: Maintained F: board/freescale/lx2160a/eth_lx2160aqds.h @@ -25,3 +27,27 @@ LX2160AQDS_SECURE_BOOT BOARD M: Udit Agarwal S: Maintained F: configs/lx2160aqds_tfa_SECURE_BOOT_defconfig + +LX2162AQDS BOARD +M: Meenakshi Aggarwal +S: Maintained +F: board/freescale/lx2160a/eth_lx2162aqds.h +F: include/configs/lx2162aqds.h +F: configs/lx2162aqds_tfa_defconfig +F: arch/arm/dts/fsl-lx2162a-qds.dts +F: arch/arm/dts/fsl-lx2162a-qds-17-x.dts +F: arch/arm/dts/fsl-lx2162a-qds-18-x.dts +F: arch/arm/dts/fsl-lx2162a-qds-20-x.dts +F: arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi +F: arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi +F: arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi + +LX2162AQDS_SECURE_BOOT BOARD +M: Manish Tomar +S: Maintained +F: configs/lx2162aqds_tfa_SECURE_BOOT_defconfig + +LX2162AQDS_VERIFIED_BOOT BOARD +M: Manish Tomar +S: Maintained +F: configs/lx2162aqds_tfa_verified_boot_defconfig diff --git a/board/freescale/lx2160a/Makefile b/board/freescale/lx2160a/Makefile index d1a621b682..c9561bfade 100644 --- a/board/freescale/lx2160a/Makefile +++ b/board/freescale/lx2160a/Makefile @@ -8,3 +8,4 @@ obj-y += lx2160a.o obj-y += ddr.o obj-$(CONFIG_TARGET_LX2160ARDB) += eth_lx2160ardb.o obj-$(CONFIG_TARGET_LX2160AQDS) += eth_lx2160aqds.o +obj-$(CONFIG_TARGET_LX2162AQDS) += eth_lx2162aqds.o diff --git a/board/freescale/lx2160a/README b/board/freescale/lx2160a/README index 62fb9eab15..7bca98dd3d 100644 --- a/board/freescale/lx2160a/README +++ b/board/freescale/lx2160a/README @@ -195,3 +195,135 @@ SERDES3 |CARDS |Connect I/O cable to IO_SLOT6(J125) ------------------------------------------------------------------------- +LX2162A SoC Overview +-------------------------------------- +For details, please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc + +LX2162AQDS board Overview +---------------------- +DDR Memory + One ports of 72-bits (8-bits ECC) DDR4. + Each port supports four chip-selects and two DIMM + connectors. Data rate upto 2.9 GT/s. + +SERDES ports + Two serdes controllers (12 lanes) + Serdes1: Supports two USXGMII connectors, each connected through + Aquantia AQR107 phy, two 25GbE SFP+ modules connected through an Inphi + IN112525 phy and one 40 GbE QSFP+ module connected through an Inphi + CS4223 phy. + + Serdes2: Supports two PCIe x4 (Gen3) and one PCIe x8 (Gen3) connector, + four SATA 3.0 connectors + +eSDHC + eSDHC1: Supports a SD connector for connecting SD cards + eSDHC2: Supports 128GB Micron MTFC128GAJAECE-IT eMMC + +Octal SPI (XSPI) + Supports two 64 MB onbpard octal SPI flash memories, one SPI emulator + for off-board emulation + +I2C All system devices on I2C1 multiplexed using PCA9547 multiplexer + Serial Ports + +USB 3.0 + One high speed USB 3.0 ports. First USB 3.0 port configured as Host + with Type-A connector, second USB 3.0 port configured as OTG with + micro-AB connector + +Serial Ports Two UART ports +Ethernet Two RGMII interfaces +Debug ARM JTAG support + +Booting Options +--------------- +a) Flexspi boot +b) SD boot +c) eMMC boot + +Memory map for Flexspi flash +---------------------------- +Image Flash Offset +bl2_flexspi_nor.pbl (RCW+PBI+bl2.pbl) 0x00000000 +fip.bin (bl31 + bl33(u-boot) + + header for Secure-boot(secure-boot only)) 0x00100000 +Boot firmware Environment 0x00500000 +DDR PHY Firmware (fip_ddr_all.bin) 0x00800000 +DPAA2 MC Firmware 0x00A00000 +DPAA2 DPL 0x00D00000 +DPAA2 DPC 0x00E00000 +Kernel.itb 0x01000000 + +Memory map for sd/eMMC card +---------------------------- +Image SD/eMMC card Offset +bl2_sd.pbl (RCW+PBI+bl2.pbl) 0x00008 +fip.bin (bl31 + bl33(u-boot) + + header for Secure-boot(secure-boot only)) 0x00800 +Boot firmware Environment 0x02800 +DDR PHY Firmware (fip_ddr_all.bin) 0x04000 +DPAA2 MC Firmware 0x05000 +DPAA2 DPL 0x06800 +DPAA2 DPC 0x07000 +Kernel.itb 0x08000 + +Various Mezzanine cards and their connection for different SERDES protocols is +as below: + +SERDES1 |CARDS +----------------------------------------------------------------------- +1 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) +------------------------------------------------------------------------ +3 |Mezzanine:X-M11-USXGMII (29828) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) +------------------------------------------------------------------------ +15 |Mezzanine:X-M8-50G (29734) + |Connect Hydra Cable (HDR-198816-XX-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) +------------------------------------------------------------------------ +17 |Mezzanine:X-M13-25G (32133) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J110) +------------------------------------------------------------------------ +18 |Mezzanine:X-M11-USXGMII (29828), X-M13-25G (32133) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT1 (J108) + |Connect M11 I/O cable to IO_SLOT1(J110), M13 I/O cable to IO_SLOT6(J125) +------------------------------------------------------------------------ +20 |Mezzanine:X-M7-40G (29738) + |Connect Straight Cable (HDR-198816-XX-ECUE) to SD_SLOT1 (J108) + |Connect I/O cable to IO_SLOT1(J108) +------------------------------------------------------------------------ + + +SERDES2 |CARDS +----------------------------------------------------------------------- +2 |Mezzanine:X-M6-PCIE-X8 (29737) * + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect Straight Cable (HDR-198816-XX-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT3(J116) +------------------------------------------------------------------------ +3 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect I/O cable to IO_SLOT3(J116) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT4(J119) +------------------------------------------------------------------------ +5 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect I/O cable to IO_SLOT3(J116) + |Mezzanine:X-M5-SATA (29687) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT4(J119) +------------------------------------------------------------------------ +11 |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT3 (J114) + |Connect I/O cable to IO_SLOT7(J127) + |Mezzanine:X-M4-PCIE-SGMII (29733) + |Connect Hydra Cable (HDR-198564-01-ECUE) to SD_SLOT4 (J117) + |Connect I/O cable to IO_SLOT8(J131) +------------------------------------------------------------------------ diff --git a/board/freescale/lx2160a/eth_lx2160ardb.c b/board/freescale/lx2160a/eth_lx2160ardb.c index b448883ee1..b3125b7748 100644 --- a/board/freescale/lx2160a/eth_lx2160ardb.c +++ b/board/freescale/lx2160a/eth_lx2160ardb.c @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0+ /* - * Copyright 2018 NXP + * Copyright 2018, 2020 NXP * */ @@ -19,6 +19,7 @@ #include #include #include +#include "lx2160a.h" DECLARE_GLOBAL_DATA_PTR; diff --git a/board/freescale/lx2160a/eth_lx2162aqds.c b/board/freescale/lx2160a/eth_lx2162aqds.c new file mode 100644 index 0000000000..4683f674f0 --- /dev/null +++ b/board/freescale/lx2160a/eth_lx2162aqds.c @@ -0,0 +1,974 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 NXP + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "../common/qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +#ifndef CONFIG_DM_ETH +#define EMI_NONE 0 +#define EMI1 1 /* Mdio Bus 1 */ +#define EMI2 2 /* Mdio Bus 2 */ + +#if defined(CONFIG_FSL_MC_ENET) +enum io_slot { + IO_SLOT_NONE = 0, + IO_SLOT_1, + IO_SLOT_2, + IO_SLOT_3, + IO_SLOT_4, + IO_SLOT_5, + IO_SLOT_6, + IO_SLOT_7, + IO_SLOT_8, + EMI1_RGMII1, + EMI1_RGMII2, + IO_SLOT_MAX +}; + +struct lx2162a_qds_mdio { + enum io_slot ioslot : 4; + u8 realbusnum : 4; + struct mii_dev *realbus; +}; + +/* structure explaining the phy configuration on 8 lanes of a serdes*/ +struct serdes_phy_config { + u8 serdes; /* serdes protocol */ + struct phy_config { + u8 dpmacid; + /* -1 terminated array */ + int phy_address[WRIOP_MAX_PHY_NUM + 1]; + u8 mdio_bus; + enum io_slot ioslot; + } phy_config[SRDS_MAX_LANES]; +}; + +/* Table defining the phy configuration on 8 lanes of a serdes. + * Various assumptions have been made while defining this table. + * e.g. for serdes1 protocol 19 it is being assumed that X-M11-USXGMII + * card is being used for dpmac 3-4. (X-M12-XFI could also have been used) + * And also that this card is connected to IO Slot 1 (could have been connected + * to any of the 8 IO slots (IO slot 1 - IO slot 8)). + * similarly, it is also being assumed that MDIO 1 is selected on X-M7-40G card + * used in serdes1 protocol 19 (could have selected MDIO 2) + * To override these settings "dpmac" environment variable can be used after + * defining "dpmac_override" in hwconfig environment variable. + * This table has limited serdes protocol entries. It can be expanded as per + * requirement. + */ +/***************************************************************** + *| SERDES_1 PROTOCOL | IO_SLOT | CARD | + ****************************************************************** + *| 2 | IO_SLOT_1 | M4-PCIE-SGMII | + *| 3 | IO_SLOT_1 | M11-USXGMII | + *| 15 | IO_SLOT_1 | M13-25G | + *| 17 | IO_SLOT_1 | M13-25G | + *| 18 | IO_SLOT_1 | M11-USXGMII | + *| | IO_SLOT_6 | M13-25G | + *| 20 | IO_SLOT_1 | M7-40G | + ***************************************************************** + */ +static const struct serdes_phy_config serdes1_phy_config[] = { + {1, {} }, + {2, {{WRIOP1_DPMAC3, {SGMII_CARD_PORT1_PHY_ADDR, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC6, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_1} } }, + {3, {{WRIOP1_DPMAC3, {AQ_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {AQ_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {AQ_PHY_ADDR3, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC6, {AQ_PHY_ADDR4, -1}, + EMI1, IO_SLOT_1} } }, + {15, {{WRIOP1_DPMAC1, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC2, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1} } }, + {17, {{WRIOP1_DPMAC3, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC6, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1} } }, + {18, {{WRIOP1_DPMAC3, {AQ_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {AQ_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_6}, + {WRIOP1_DPMAC6, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_6} } }, + {20, {{WRIOP1_DPMAC1, {CORTINA_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1} } } +}; + +/***************************************************************** + *| SERDES_2 PROTOCOL | IO_SLOT | CARD | + ****************************************************************** + *| 2 | IO_SLOT_7 | M4-PCIE-SGMII | + *| | IO_SLOT_8 | M4-PCIE-SGMII | + *| 3 | IO_SLOT_7 | M4-PCIE-SGMII | + *| | IO_SLOT_8 | M4-PCIE-SGMII | + *| 5 | IO_SLOT_7 | M4-PCIE-SGMII | + *| 10 | IO_SLOT_7 | M4-PCIE-SGMII | + *| | IO_SLOT_8 | M4-PCIE-SGMII | + *| 11 | IO_SLOT_7 | M4-PCIE-SGMII | + *| | IO_SLOT_8 | M4-PCIE-SGMII | + *| 12 | IO_SLOT_7 | M4-PCIE-SGMII | + *| | IO_SLOT_8 | M4-PCIE-SGMII | + ****************************************************************** + */ +static const struct serdes_phy_config serdes2_phy_config[] = { + {2, {} }, + {3, {} }, + {5, {} }, + {10, {{WRIOP1_DPMAC11, {SGMII_CARD_PORT1_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC12, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC17, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC18, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_7} } }, + {11, {{WRIOP1_DPMAC12, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC17, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC18, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC16, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_8}, + {WRIOP1_DPMAC13, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_8}, + {WRIOP1_DPMAC14, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_8} } }, + {12, {{WRIOP1_DPMAC11, {SGMII_CARD_PORT1_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC12, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC17, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC18, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_7} } } +}; + +static inline +const struct phy_config *get_phy_config(u8 serdes, + const struct serdes_phy_config *table, + u8 table_size) +{ + int i; + + for (i = 0; i < table_size; i++) { + if (table[i].serdes == serdes) + return table[i].phy_config; + } + + return NULL; +} + +/* BRDCFG4 controls EMI routing for the board. + * Bits Function + * 7-6 EMI Interface #1 Primary Routing (CFG_MUX1_EMI1) (1.8V): + * EMI1 00= On-board PHY #1 + * 01= On-board PHY #2 + * 10= (reserved) + * 11= Slots 1..8 multiplexer and translator. + * 5-3 EMI Interface #1 Secondary Routing (CFG_MUX2_EMI1) (2.5V): + * EMI1X 000= Slot #1 + * 001= Slot #2 + * 010= Slot #3 + * 011= Slot #4 + * 100= Slot #5 + * 101= Slot #6 + * 110= Slot #7 + * 111= Slot #8 + * 2-0 EMI Interface #2 Routing (CFG_MUX_EMI2): + * EMI2 000= Slot #1 (secondary EMI) + * 001= Slot #2 (secondary EMI) + * 010= Slot #3 (secondary EMI) + * 011= Slot #4 (secondary EMI) + * 100= Slot #5 (secondary EMI) + * 101= Slot #6 (secondary EMI) + * 110= Slot #7 (secondary EMI) + * 111= Slot #8 (secondary EMI) + */ +static int lx2162a_qds_get_mdio_mux_val(u8 realbusnum, enum io_slot ioslot) +{ + switch (realbusnum) { + case EMI1: + switch (ioslot) { + case EMI1_RGMII1: + return 0; + case EMI1_RGMII2: + return 0x40; + default: + return (((ioslot - 1) << BRDCFG4_EMI1SEL_SHIFT) | 0xC0); + } + break; + case EMI2: + return ((ioslot - 1) << BRDCFG4_EMI2SEL_SHIFT); + default: + return -1; + } +} + +static void lx2162a_qds_mux_mdio(struct lx2162a_qds_mdio *priv) +{ + u8 brdcfg4, mux_val, reg; + + brdcfg4 = QIXIS_READ(brdcfg[4]); + reg = brdcfg4; + mux_val = lx2162a_qds_get_mdio_mux_val(priv->realbusnum, priv->ioslot); + + switch (priv->realbusnum) { + case EMI1: + brdcfg4 &= ~BRDCFG4_EMI1SEL_MASK; + brdcfg4 |= mux_val; + break; + case EMI2: + brdcfg4 &= ~BRDCFG4_EMI2SEL_MASK; + brdcfg4 |= mux_val; + break; + } + + if (brdcfg4 ^ reg) + QIXIS_WRITE(brdcfg[4], brdcfg4); +} + +static int lx2162a_qds_mdio_read(struct mii_dev *bus, int addr, + int devad, int regnum) +{ + struct lx2162a_qds_mdio *priv = bus->priv; + + lx2162a_qds_mux_mdio(priv); + + return priv->realbus->read(priv->realbus, addr, devad, regnum); +} + +static int lx2162a_qds_mdio_write(struct mii_dev *bus, int addr, int devad, + int regnum, u16 value) +{ + struct lx2162a_qds_mdio *priv = bus->priv; + + lx2162a_qds_mux_mdio(priv); + + return priv->realbus->write(priv->realbus, addr, devad, regnum, value); +} + +static int lx2162a_qds_mdio_reset(struct mii_dev *bus) +{ + struct lx2162a_qds_mdio *priv = bus->priv; + + return priv->realbus->reset(priv->realbus); +} + +static struct mii_dev *lx2162a_qds_mdio_init(u8 realbusnum, enum io_slot ioslot) +{ + struct lx2162a_qds_mdio *pmdio; + struct mii_dev *bus; + /*should be within MDIO_NAME_LEN*/ + char dummy_mdio_name[] = "LX2162A_QDS_MDIO1_IOSLOT1"; + + if (realbusnum == EMI2) { + if (ioslot < IO_SLOT_1 || ioslot > IO_SLOT_8) { + printf("invalid ioslot %d\n", ioslot); + return NULL; + } + } else if (realbusnum == EMI1) { + if (ioslot < IO_SLOT_1 || ioslot > EMI1_RGMII2) { + printf("invalid ioslot %d\n", ioslot); + return NULL; + } + } else { + printf("not supported real mdio bus %d\n", realbusnum); + return NULL; + } + + if (ioslot == EMI1_RGMII1) + strcpy(dummy_mdio_name, "LX2162A_QDS_MDIO1_RGMII1"); + else if (ioslot == EMI1_RGMII2) + strcpy(dummy_mdio_name, "LX2162A_QDS_MDIO1_RGMII2"); + else + sprintf(dummy_mdio_name, "LX2162A_QDS_MDIO%d_IOSLOT%d", + realbusnum, ioslot); + bus = miiphy_get_dev_by_name(dummy_mdio_name); + + if (bus) + return bus; + + bus = mdio_alloc(); + if (!bus) { + printf("Failed to allocate %s bus\n", dummy_mdio_name); + return NULL; + } + + pmdio = malloc(sizeof(*pmdio)); + if (!pmdio) { + printf("Failed to allocate %s private data\n", dummy_mdio_name); + free(bus); + return NULL; + } + + switch (realbusnum) { + case EMI1: + pmdio->realbus = + miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME); + break; + case EMI2: + pmdio->realbus = + miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME); + break; + } + + if (!pmdio->realbus) { + printf("No real mdio bus num %d found\n", realbusnum); + free(bus); + free(pmdio); + return NULL; + } + + pmdio->realbusnum = realbusnum; + pmdio->ioslot = ioslot; + bus->read = lx2162a_qds_mdio_read; + bus->write = lx2162a_qds_mdio_write; + bus->reset = lx2162a_qds_mdio_reset; + strcpy(bus->name, dummy_mdio_name); + bus->priv = pmdio; + + if (!mdio_register(bus)) + return bus; + + printf("No bus with name %s\n", dummy_mdio_name); + free(bus); + free(pmdio); + return NULL; +} + +static inline void do_phy_config(const struct phy_config *phy_config) +{ + struct mii_dev *bus; + int i, phy_num, phy_address; + + for (i = 0; i < SRDS_MAX_LANES; i++) { + if (!phy_config[i].dpmacid) + continue; + + for (phy_num = 0; + phy_num < ARRAY_SIZE(phy_config[i].phy_address); + phy_num++) { + phy_address = phy_config[i].phy_address[phy_num]; + if (phy_address == -1) + break; + wriop_set_phy_address(phy_config[i].dpmacid, + phy_num, phy_address); + } + /*Register the muxing front-ends to the MDIO buses*/ + bus = lx2162a_qds_mdio_init(phy_config[i].mdio_bus, + phy_config[i].ioslot); + if (!bus) + printf("could not get bus for mdio %d ioslot %d\n", + phy_config[i].mdio_bus, + phy_config[i].ioslot); + else + wriop_set_mdio(phy_config[i].dpmacid, bus); + } +} + +static inline void do_dpmac_config(int dpmac, const char *arg_dpmacid, + char *env_dpmac) +{ + const char *ret; + size_t len; + u8 realbusnum, ioslot; + struct mii_dev *bus; + int phy_num; + char *phystr = "phy00"; + + /*search phy in dpmac arg*/ + for (phy_num = 0; phy_num < WRIOP_MAX_PHY_NUM; phy_num++) { + sprintf(phystr, "phy%d", phy_num + 1); + ret = hwconfig_subarg_f(arg_dpmacid, phystr, &len, env_dpmac); + if (!ret) { + /*look for phy instead of phy1*/ + if (!phy_num) + ret = hwconfig_subarg_f(arg_dpmacid, "phy", + &len, env_dpmac); + if (!ret) + continue; + } + + if (len != 4 || strncmp(ret, "0x", 2)) + printf("invalid phy format in %s variable.\n" + "specify phy%d for %s in hex format e.g. 0x12\n", + env_dpmac, phy_num + 1, arg_dpmacid); + else + wriop_set_phy_address(dpmac, phy_num, + simple_strtoul(ret, NULL, 16)); + } + + /*search mdio in dpmac arg*/ + ret = hwconfig_subarg_f(arg_dpmacid, "mdio", &len, env_dpmac); + if (ret) + realbusnum = *ret - '0'; + else + realbusnum = EMI_NONE; + + if (realbusnum) { + /*search io in dpmac arg*/ + ret = hwconfig_subarg_f(arg_dpmacid, "io", &len, env_dpmac); + if (ret) + ioslot = *ret - '0'; + else + ioslot = IO_SLOT_NONE; + /*Register the muxing front-ends to the MDIO buses*/ + bus = lx2162a_qds_mdio_init(realbusnum, ioslot); + if (!bus) + printf("could not get bus for mdio %d ioslot %d\n", + realbusnum, ioslot); + else + wriop_set_mdio(dpmac, bus); + } +} + +#endif +#endif /* !CONFIG_DM_ETH */ + +int board_eth_init(struct bd_info *bis) +{ +#ifndef CONFIG_DM_ETH +#if defined(CONFIG_FSL_MC_ENET) + struct memac_mdio_info mdio_info; + struct memac_mdio_controller *regs; + int i; + const char *ret; + char *env_dpmac; + char dpmacid[] = "dpmac00", srds[] = "00_00_00"; + size_t len; + struct mii_dev *bus; + const struct phy_config *phy_config; + struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 srds_s1, srds_s2; + + srds_s1 = in_le32(&gur->rcwsr[28]) & + FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK; + srds_s1 >>= FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT; + + srds_s2 = in_le32(&gur->rcwsr[28]) & + FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK; + srds_s2 >>= FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT; + + sprintf(srds, "%d_%d", srds_s1, srds_s2); + + regs = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO1; + mdio_info.regs = regs; + mdio_info.name = DEFAULT_WRIOP_MDIO1_NAME; + + /*Register the EMI 1*/ + fm_memac_mdio_init(bis, &mdio_info); + + regs = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO2; + mdio_info.regs = regs; + mdio_info.name = DEFAULT_WRIOP_MDIO2_NAME; + + /*Register the EMI 2*/ + fm_memac_mdio_init(bis, &mdio_info); + + /* "dpmac" environment variable can be used after + * defining "dpmac_override" in hwconfig environment variable. + */ + if (hwconfig("dpmac_override")) { + env_dpmac = env_get("dpmac"); + if (env_dpmac) { + ret = hwconfig_arg_f("srds", &len, env_dpmac); + if (ret) { + if (strncmp(ret, srds, strlen(srds))) { + printf("SERDES configuration changed.\n" + "previous: %.*s, current: %s.\n" + "update dpmac variable.\n", + (int)len, ret, srds); + } + } else { + printf("SERDES configuration not found.\n" + "Please add srds:%s in dpmac variable\n", + srds); + } + + for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) { + /* Look for dpmac1 to dpmac24(current max) arg + * in dpmac environment variable + */ + sprintf(dpmacid, "dpmac%d", i); + ret = hwconfig_arg_f(dpmacid, &len, env_dpmac); + if (ret) + do_dpmac_config(i, dpmacid, env_dpmac); + } + } else { + printf("Warning: environment dpmac not found.\n" + "DPAA network interfaces may not work\n"); + } + } else { + /*Look for phy config for serdes1 in phy config table*/ + phy_config = get_phy_config(srds_s1, serdes1_phy_config, + ARRAY_SIZE(serdes1_phy_config)); + if (!phy_config) { + printf("%s WRIOP: Unsupported SerDes1 Protocol %d\n", + __func__, srds_s1); + } else { + do_phy_config(phy_config); + } + phy_config = get_phy_config(srds_s2, serdes2_phy_config, + ARRAY_SIZE(serdes2_phy_config)); + if (!phy_config) { + printf("%s WRIOP: Unsupported SerDes2 Protocol %d\n", + __func__, srds_s2); + } else { + do_phy_config(phy_config); + } + } + + if (wriop_get_enet_if(WRIOP1_DPMAC17) == PHY_INTERFACE_MODE_RGMII_ID) { + wriop_set_phy_address(WRIOP1_DPMAC17, 0, RGMII_PHY_ADDR1); + bus = lx2162a_qds_mdio_init(EMI1, EMI1_RGMII1); + if (!bus) + printf("could not get bus for RGMII1\n"); + else + wriop_set_mdio(WRIOP1_DPMAC17, bus); + } + + if (wriop_get_enet_if(WRIOP1_DPMAC18) == PHY_INTERFACE_MODE_RGMII_ID) { + wriop_set_phy_address(WRIOP1_DPMAC18, 0, RGMII_PHY_ADDR2); + bus = lx2162a_qds_mdio_init(EMI1, EMI1_RGMII2); + if (!bus) + printf("could not get bus for RGMII2\n"); + else + wriop_set_mdio(WRIOP1_DPMAC18, bus); + } + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ +#endif /* !CONFIG_DM_ETH */ + +#ifdef CONFIG_PHY_AQUANTIA + /* + * Export functions to be used by AQ firmware + * upload application + */ + gd->jt->strcpy = strcpy; + gd->jt->mdelay = mdelay; + gd->jt->mdio_get_current_dev = mdio_get_current_dev; + gd->jt->phy_find_by_mask = phy_find_by_mask; + gd->jt->mdio_phydev_for_ethname = mdio_phydev_for_ethname; + gd->jt->miiphy_set_current_dev = miiphy_set_current_dev; +#endif + +#ifdef CONFIG_DM_ETH + return 0; +#else + return pci_eth_init(bis); +#endif +} + +#if defined(CONFIG_RESET_PHY_R) +void reset_phy(void) +{ +#if defined(CONFIG_FSL_MC_ENET) + mc_env_boot(); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ + +#ifndef CONFIG_DM_ETH +#if defined(CONFIG_FSL_MC_ENET) +int fdt_fixup_dpmac_phy_handle(void *fdt, int dpmac_id, int node_phandle) +{ + int offset; + int ret; + char dpmac_str[] = "dpmacs@00"; + const char *phy_string; + + offset = fdt_path_offset(fdt, "/soc/fsl-mc/dpmacs"); + + if (offset < 0) + offset = fdt_path_offset(fdt, "/fsl-mc/dpmacs"); + + if (offset < 0) { + printf("dpmacs node not found in device tree\n"); + return offset; + } + + sprintf(dpmac_str, "dpmac@%x", dpmac_id); + debug("dpmac_str = %s\n", dpmac_str); + + offset = fdt_subnode_offset(fdt, offset, dpmac_str); + if (offset < 0) { + printf("%s node not found in device tree\n", dpmac_str); + return offset; + } + + phy_string = fdt_getprop(fdt, offset, "phy-connection-type", NULL); + if (is_backplane_mode(phy_string)) { + /* Backplane KR mode: skip fixups */ + printf("Interface %d in backplane KR mode\n", dpmac_id); + return 0; + } + + ret = fdt_appendprop_cell(fdt, offset, "phy-handle", node_phandle); + if (ret) + printf("%d@%s %d\n", __LINE__, __func__, ret); + + phy_string = phy_string_for_interface(wriop_get_enet_if(dpmac_id)); + ret = fdt_setprop_string(fdt, offset, "phy-connection-type", + phy_string); + if (ret) + printf("%d@%s %d\n", __LINE__, __func__, ret); + + return ret; +} + +int fdt_get_ioslot_offset(void *fdt, struct mii_dev *mii_dev, int fpga_offset) +{ + char mdio_ioslot_str[] = "mdio@00"; + struct lx2162a_qds_mdio *priv; + u64 reg; + u32 phandle; + int offset, mux_val; + + /*Test if the MDIO bus is real mdio bus or muxing front end ?*/ + if (strncmp(mii_dev->name, "LX2162A_QDS_MDIO", + strlen("LX2162A_QDS_MDIO"))) + return -1; + + /*Get the real MDIO bus num and ioslot info from bus's priv data*/ + priv = mii_dev->priv; + + debug("real_bus_num = %d, ioslot = %d\n", + priv->realbusnum, priv->ioslot); + + if (priv->realbusnum == EMI1) + reg = CONFIG_SYS_FSL_WRIOP1_MDIO1; + else + reg = CONFIG_SYS_FSL_WRIOP1_MDIO2; + + offset = fdt_node_offset_by_compat_reg(fdt, "fsl,fman-memac-mdio", reg); + if (offset < 0) { + printf("mdio@%llx node not found in device tree\n", reg); + return offset; + } + + phandle = fdt_get_phandle(fdt, offset); + phandle = cpu_to_fdt32(phandle); + offset = fdt_node_offset_by_prop_value(fdt, -1, "mdio-parent-bus", + &phandle, 4); + if (offset < 0) { + printf("mdio-mux-%d node not found in device tree\n", + priv->realbusnum == EMI1 ? 1 : 2); + return offset; + } + + mux_val = lx2162a_qds_get_mdio_mux_val(priv->realbusnum, priv->ioslot); + if (priv->realbusnum == EMI1) + mux_val >>= BRDCFG4_EMI1SEL_SHIFT; + else + mux_val >>= BRDCFG4_EMI2SEL_SHIFT; + sprintf(mdio_ioslot_str, "mdio@%x", (u8)mux_val); + + offset = fdt_subnode_offset(fdt, offset, mdio_ioslot_str); + if (offset < 0) { + printf("%s node not found in device tree\n", mdio_ioslot_str); + return offset; + } + + return offset; +} + +int fdt_create_phy_node(void *fdt, int offset, u8 phyaddr, int *subnodeoffset, + struct phy_device *phy_dev, int phandle) +{ + char phy_node_name[] = "ethernet-phy@00"; + char phy_id_compatible_str[] = "ethernet-phy-id0000.0000,"; + int ret; + + sprintf(phy_node_name, "ethernet-phy@%x", phyaddr); + debug("phy_node_name = %s\n", phy_node_name); + + *subnodeoffset = fdt_add_subnode(fdt, offset, phy_node_name); + if (*subnodeoffset <= 0) { + printf("Could not add subnode %s inside node %s err = %s\n", + phy_node_name, fdt_get_name(fdt, offset, NULL), + fdt_strerror(*subnodeoffset)); + return *subnodeoffset; + } + + sprintf(phy_id_compatible_str, "ethernet-phy-id%04x.%04x,", + phy_dev->phy_id >> 16, phy_dev->phy_id & 0xFFFF); + debug("phy_id_compatible_str %s\n", phy_id_compatible_str); + + ret = fdt_setprop_string(fdt, *subnodeoffset, "compatible", + phy_id_compatible_str); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + + if (phy_dev->is_c45) { + ret = fdt_appendprop_string(fdt, *subnodeoffset, "compatible", + "ethernet-phy-ieee802.3-c45"); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + } else { + ret = fdt_appendprop_string(fdt, *subnodeoffset, "compatible", + "ethernet-phy-ieee802.3-c22"); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + } + + ret = fdt_setprop_cell(fdt, *subnodeoffset, "reg", phyaddr); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + + ret = fdt_set_phandle(fdt, *subnodeoffset, phandle); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + +out: + if (ret) + fdt_del_node(fdt, *subnodeoffset); + + return ret; +} + +#define is_rgmii(dpmac_id) \ + wriop_get_enet_if((dpmac_id)) == PHY_INTERFACE_MODE_RGMII_ID + +int fdt_fixup_board_phy(void *fdt) +{ + int fpga_offset, offset, subnodeoffset; + struct mii_dev *mii_dev; + struct list_head *mii_devs, *entry; + int ret, dpmac_id, phandle, i; + struct phy_device *phy_dev; + char ethname[ETH_NAME_LEN]; + phy_interface_t phy_iface; + + ret = 0; + /* we know FPGA is connected to i2c0, therefore search path directly, + * instead of compatible property, as it saves time + */ + fpga_offset = fdt_path_offset(fdt, "/soc/i2c@2000000/fpga"); + + if (fpga_offset < 0) + fpga_offset = fdt_path_offset(fdt, "/i2c@2000000/fpga"); + + if (fpga_offset < 0) { + printf("i2c@2000000/fpga node not found in device tree\n"); + return fpga_offset; + } + + phandle = fdt_alloc_phandle(fdt); + mii_devs = mdio_get_list_head(); + + list_for_each(entry, mii_devs) { + mii_dev = list_entry(entry, struct mii_dev, link); + debug("mii_dev name : %s\n", mii_dev->name); + offset = fdt_get_ioslot_offset(fdt, mii_dev, fpga_offset); + if (offset < 0) + continue; + + // Look for phy devices attached to MDIO bus muxing front end + // and create their entries with compatible being the device id + for (i = 0; i < PHY_MAX_ADDR; i++) { + phy_dev = mii_dev->phymap[i]; + if (!phy_dev) + continue; + + // TODO: use sscanf instead of loop + dpmac_id = WRIOP1_DPMAC1; + while (dpmac_id < NUM_WRIOP_PORTS) { + phy_iface = wriop_get_enet_if(dpmac_id); + snprintf(ethname, ETH_NAME_LEN, "DPMAC%d@%s", + dpmac_id, + phy_string_for_interface(phy_iface)); + if (strcmp(ethname, phy_dev->dev->name) == 0) + break; + dpmac_id++; + } + if (dpmac_id == NUM_WRIOP_PORTS) + continue; + + if ((dpmac_id == 17 || dpmac_id == 18) && + is_rgmii(dpmac_id)) + continue; + + ret = fdt_create_phy_node(fdt, offset, i, + &subnodeoffset, + phy_dev, phandle); + if (ret) + break; + + ret = fdt_fixup_dpmac_phy_handle(fdt, + dpmac_id, phandle); + if (ret) { + fdt_del_node(fdt, subnodeoffset); + break; + } + /* calculate offset again as new node addition may have + * changed offset; + */ + offset = fdt_get_ioslot_offset(fdt, mii_dev, + fpga_offset); + phandle++; + } + + if (ret) + break; + } + + return ret; +} +#endif // CONFIG_FSL_MC_ENET +#endif + +#if defined(CONFIG_DM_ETH) && defined(CONFIG_MULTI_DTB_FIT) + +/* Structure to hold SERDES protocols supported in case of + * CONFIG_DM_ETH enabled (network interfaces are described in the DTS). + * + * @serdes_block: the index of the SERDES block + * @serdes_protocol: the decimal value of the protocol supported + * @dts_needed: DTS notes describing the current configuration are needed + * + * When dts_needed is true, the board_fit_config_name_match() function + * will try to exactly match the current configuration of the block with a DTS + * name provided. + */ +static struct serdes_configuration { + u8 serdes_block; + u32 serdes_protocol; + bool dts_needed; +} supported_protocols[] = { + /* Serdes block #1 */ + {1, 2, true}, + {1, 3, true}, + {1, 15, true}, + {1, 17, true}, + {1, 18, true}, + {1, 20, true}, + + /* Serdes block #2 */ + {2, 2, false}, + {2, 3, false}, + {2, 5, false}, + {2, 10, false}, + {2, 11, true}, + {2, 12, true}, +}; + +#define SUPPORTED_SERDES_PROTOCOLS ARRAY_SIZE(supported_protocols) + +static bool protocol_supported(u8 serdes_block, u32 protocol) +{ + struct serdes_configuration serdes_conf; + int i; + + for (i = 0; i < SUPPORTED_SERDES_PROTOCOLS; i++) { + serdes_conf = supported_protocols[i]; + if (serdes_conf.serdes_block == serdes_block && + serdes_conf.serdes_protocol == protocol) + return true; + } + + return false; +} + +static void get_str_protocol(u8 serdes_block, u32 protocol, char *str) +{ + struct serdes_configuration serdes_conf; + int i; + + for (i = 0; i < SUPPORTED_SERDES_PROTOCOLS; i++) { + serdes_conf = supported_protocols[i]; + if (serdes_conf.serdes_block == serdes_block && + serdes_conf.serdes_protocol == protocol) { + if (serdes_conf.dts_needed == true) + sprintf(str, "%u", protocol); + else + sprintf(str, "x"); + return; + } + } +} + +int board_fit_config_name_match(const char *name) +{ + struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 rcw_status = in_le32(&gur->rcwsr[28]); + char srds_s1_str[2], srds_s2_str[2]; + u32 srds_s1, srds_s2; + char expected_dts[100]; + + srds_s1 = rcw_status & FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK; + srds_s1 >>= FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT; + + srds_s2 = rcw_status & FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK; + srds_s2 >>= FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT; + + /* Check for supported protocols. The default DTS will be used + * in this case + */ + if (!protocol_supported(1, srds_s1) || + !protocol_supported(2, srds_s2)) + return -1; + + get_str_protocol(1, srds_s1, srds_s1_str); + get_str_protocol(2, srds_s2, srds_s2_str); + + sprintf(expected_dts, "fsl-lx2160a-qds-%s-%s", + srds_s1_str, srds_s2_str); + + if (!strcmp(name, expected_dts)) + return 0; + + return -1; +} +#endif diff --git a/board/freescale/lx2160a/lx2160a.c b/board/freescale/lx2160a/lx2160a.c index 0ff987eeb4..222906fdff 100644 --- a/board/freescale/lx2160a/lx2160a.c +++ b/board/freescale/lx2160a/lx2160a.c @@ -32,12 +32,13 @@ #include "../common/vid.h" #include #include +#include "lx2160a.h" #ifdef CONFIG_EMC2305 #include "../common/emc2305.h" #endif -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) #define CFG_MUX_I2C_SDHC(reg, value) ((reg & 0x3f) | value) #define SET_CFG_MUX1_SDHC1_SDHC(reg) (reg & 0x3f) #define SET_CFG_MUX2_SDHC1_SPI(reg, value) ((reg & 0xcf) | value) @@ -47,7 +48,7 @@ #define SDHC1_BASE_PMUX_DSPI 2 #define SDHC2_BASE_PMUX_DSPI 2 #define IIC5_PMUX_SPI3 3 -#endif /* CONFIG_TARGET_LX2160AQDS */ +#endif /* CONFIG_TARGET_LX2160AQDS or CONFIG_TARGET_LX2162AQDS */ DECLARE_GLOBAL_DATA_PTR; @@ -191,7 +192,7 @@ int board_fix_fdt(void *fdt) } #endif -#if defined(CONFIG_TARGET_LX2160AQDS) +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) void esdhc_dspi_status_fixup(void *blob) { const char esdhc0_path[] = "/soc/esdhc@2140000"; @@ -259,7 +260,7 @@ void esdhc_dspi_status_fixup(void *blob) int esdhc_status_fixup(void *blob, const char *compat) { -#if defined(CONFIG_TARGET_LX2160AQDS) +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) /* Enable esdhc and dspi DT nodes based on RCW fields */ esdhc_dspi_status_fixup(blob); #else @@ -297,7 +298,7 @@ int checkboard(void) enum boot_src src = get_boot_src(); char buf[64]; u8 sw; -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) int clock; static const char *const freq[] = {"100", "125", "156.25", "161.13", "322.26", "", "", "", @@ -306,7 +307,7 @@ int checkboard(void) #endif cpu_name(buf); -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) printf("Board: %s-QDS, ", buf); #else printf("Board: %s-RDB, ", buf); @@ -339,7 +340,13 @@ int checkboard(void) break; } } -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160ARDB) + printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata)); + + puts("SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz\n"); + puts("SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); + puts("SERDES3 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); +#else printf("FPGA: v%d (%s), build %d", (int)QIXIS_READ(scver), qixis_read_tag(buf), (int)qixis_read_minor()); @@ -350,31 +357,27 @@ int checkboard(void) sw = QIXIS_READ(brdcfg[2]); clock = sw >> 4; printf("Clock1 = %sMHz ", freq[clock]); +#if defined(CONFIG_TARGET_LX2160AQDS) clock = sw & 0x0f; printf("Clock2 = %sMHz", freq[clock]); - +#endif sw = QIXIS_READ(brdcfg[3]); puts("\nSERDES2 Reference : "); clock = sw >> 4; printf("Clock1 = %sMHz ", freq[clock]); clock = sw & 0x0f; - printf("Clock2 = %sMHz", freq[clock]); - + printf("Clock2 = %sMHz\n", freq[clock]); +#if defined(CONFIG_TARGET_LX2160AQDS) sw = QIXIS_READ(brdcfg[12]); - puts("\nSERDES3 Reference : "); + puts("SERDES3 Reference : "); clock = sw >> 4; printf("Clock1 = %sMHz Clock2 = %sMHz\n", freq[clock], freq[clock]); -#else - printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata)); - - puts("SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz\n"); - puts("SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); - puts("SERDES3 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); +#endif #endif return 0; } -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) /* * implementation of CONFIG_ESDHC_DETECT_QUIRK Macro. */ @@ -562,7 +565,7 @@ int config_board_mux(void) unsigned long get_board_sys_clk(void) { -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) u8 sysclk_conf = QIXIS_READ(brdcfg[1]); switch (sysclk_conf & 0x03) { @@ -581,7 +584,7 @@ unsigned long get_board_sys_clk(void) unsigned long get_board_ddr_clk(void) { -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); switch ((ddrclk_conf & 0x30) >> 4) { diff --git a/board/freescale/lx2160a/lx2160a.h b/board/freescale/lx2160a/lx2160a.h new file mode 100644 index 0000000000..52b020765d --- /dev/null +++ b/board/freescale/lx2160a/lx2160a.h @@ -0,0 +1,61 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 NXP + */ + +#ifndef __LX2160_H +#define __LX2160_H + +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) +/* SYSCLK */ +#define QIXIS_SYSCLK_100 0x0 +#define QIXIS_SYSCLK_125 0x1 +#define QIXIS_SYSCLK_133 0x2 + +/* DDRCLK */ +#define QIXIS_DDRCLK_100 0x0 +#define QIXIS_DDRCLK_125 0x1 +#define QIXIS_DDRCLK_133 0x2 + +#define BRDCFG4_EMI1SEL_MASK 0xF8 +#define BRDCFG4_EMI1SEL_SHIFT 3 +#define BRDCFG4_EMI2SEL_MASK 0x07 +#define BRDCFG4_EMI2SEL_SHIFT 0 +#endif + +#define QIXIS_XMAP_SHIFT 5 + +/* RTC */ +#define I2C_MUX_CH_RTC 0xB + +/* MAC/PHY configuration */ +#if defined(CONFIG_FSL_MC_ENET) +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) +#define AQ_PHY_ADDR1 0x00 +#define AQ_PHY_ADDR2 0x01 +#define AQ_PHY_ADDR3 0x02 +#define AQ_PHY_ADDR4 0x03 +#endif + +#ifdef CONFIG_TARGET_LX2160ARDB +#define AQR107_PHY_ADDR1 0x04 +#define AQR107_PHY_ADDR2 0x05 +#define AQR107_IRQ_MASK 0x0C +#endif + +#define CORTINA_PHY_ADDR1 0x0 +#define INPHI_PHY_ADDR1 0x0 + +#define RGMII_PHY_ADDR1 0x01 +#define RGMII_PHY_ADDR2 0x02 + +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) +#define INPHI_PHY_ADDR2 0x1 +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x1D +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x1F +#endif +#endif + +#endif /* __LX2160_H */ diff --git a/configs/lx2162aqds_tfa_SECURE_BOOT_defconfig b/configs/lx2162aqds_tfa_SECURE_BOOT_defconfig new file mode 100644 index 0000000000..11fe33b0fa --- /dev/null +++ b/configs/lx2162aqds_tfa_SECURE_BOOT_defconfig @@ -0,0 +1,98 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2162AQDS=y +CONFIG_TFABOOT=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_NXP_ESBC=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x500000 +CONFIG_FSPI_AHB_EN_4BYTE=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf" +# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_MISC_INIT_R=y +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_OF_BOARD_FIXUP=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2162a-qds" +CONFIG_OF_LIST="fsl-lx2162a-qds-17-x fsl-lx2162a-qds-18-x fsl-lx2162a-qds-20-x" +CONFIG_MULTI_DTB_FIT=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_ADDR=0x20500000 +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SATA_CEVA=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_EON=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_AQUANTIA=y +CONFIG_PHY_CORTINA=y +CONFIG_SYS_CORTINA_NO_FW_UPLOAD=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_VITESSE=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_DM_MDIO_MUX=y +CONFIG_E1000=y +CONFIG_MDIO_MUX_I2CREG=y +CONFIG_FSL_LS_MDIO=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE_RC=y +CONFIG_DM_SCSI=y +CONFIG_DM_SERIAL=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_DSPI=y +CONFIG_NXP_FSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_WDT=y +CONFIG_WDT_SBSA=y +CONFIG_RSA=y +CONFIG_SPL_RSA=y +CONFIG_RSA_SOFTWARE_EXP=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y +CONFIG_GIC_V3_ITS=y +CONFIG_DM_I2C=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_I2C_DEFAULT_BUS_NUMBER=0 +CONFIG_DM_RTC=y +CONFIG_DM_GPIO=y +CONFIG_CMD_DATE=y +CONFIG_RTC_PCF2127=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y diff --git a/configs/lx2162aqds_tfa_defconfig b/configs/lx2162aqds_tfa_defconfig new file mode 100644 index 0000000000..ca7479793d --- /dev/null +++ b/configs/lx2162aqds_tfa_defconfig @@ -0,0 +1,96 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2162AQDS=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x500000 +CONFIG_FSPI_AHB_EN_4BYTE=y +CONFIG_TFABOOT=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf" +# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_MISC_INIT_R=y +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_OF_BOARD_FIXUP=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2162a-qds" +CONFIG_OF_LIST="fsl-lx2162a-qds-17-x fsl-lx2162a-qds-18-x fsl-lx2162a-qds-20-x" +CONFIG_MULTI_DTB_FIT=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_ADDR=0x20500000 +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SATA_CEVA=y +CONFIG_FSL_CAAM=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_EON=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_AQUANTIA=y +CONFIG_PHY_CORTINA=y +CONFIG_SYS_CORTINA_NO_FW_UPLOAD=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_VITESSE=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_DM_MDIO_MUX=y +CONFIG_E1000=y +CONFIG_MDIO_MUX_I2CREG=y +CONFIG_FSL_LS_MDIO=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE_RC=y +CONFIG_DM_SCSI=y +CONFIG_DM_SERIAL=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_DSPI=y +CONFIG_NXP_FSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_WDT=y +CONFIG_WDT_SBSA=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y +CONFIG_GIC_V3_ITS=y +CONFIG_DM_I2C=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_I2C_DEFAULT_BUS_NUMBER=0 +CONFIG_DM_RTC=y +CONFIG_DM_GPIO=y +CONFIG_CMD_DATE=y +CONFIG_RTC_PCF2127=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y diff --git a/configs/lx2162aqds_tfa_verified_boot_defconfig b/configs/lx2162aqds_tfa_verified_boot_defconfig new file mode 100644 index 0000000000..1199b6c63d --- /dev/null +++ b/configs/lx2162aqds_tfa_verified_boot_defconfig @@ -0,0 +1,103 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2162AQDS=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x500000 +CONFIG_FSPI_AHB_EN_4BYTE=y +CONFIG_TFABOOT=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_FIT_VERBOSE=y +CONFIG_FIT_SIGNATURE=y +CONFIG_RSA=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf" +# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_MISC_INIT_R=y +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_OF_BOARD_FIXUP=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2162a-qds" +CONFIG_OF_LIST="fsl-lx2162a-qds-17-x fsl-lx2162a-qds-18-x fsl-lx2162a-qds-20-x" +CONFIG_MULTI_DTB_FIT=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_ADDR=0x20500000 +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SATA_CEVA=y +CONFIG_FSL_CAAM=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_EON=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_AQUANTIA=y +CONFIG_PHY_CORTINA=y +CONFIG_SYS_CORTINA_NO_FW_UPLOAD=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_VITESSE=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_DM_MDIO_MUX=y +CONFIG_E1000=y +CONFIG_MDIO_MUX_I2CREG=y +CONFIG_FSL_LS_MDIO=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE_RC=y +CONFIG_DM_SCSI=y +CONFIG_DM_SERIAL=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_DSPI=y +CONFIG_NXP_FSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_WDT=y +CONFIG_WDT_SBSA=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y +CONFIG_GIC_V3_ITS=y +CONFIG_DM_I2C=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_I2C_DEFAULT_BUS_NUMBER=0 +CONFIG_DM_RTC=y +CONFIG_DM_GPIO=y +CONFIG_CMD_DATE=y +CONFIG_RTC_PCF2127=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_TEE=y +CONFIG_OPTEE=y +CONFIG_CMD_OPTEE_RPMB=y +CONFIG_OPTEE_TA_AVB=y +CONFIG_SUPPORT_EMMC_RPMB=y diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h index 0017ac5773..837760fe46 100644 --- a/include/configs/lx2160a_common.h +++ b/include/configs/lx2160a_common.h @@ -149,8 +149,10 @@ /* USB */ #ifdef CONFIG_USB #define CONFIG_HAS_FSL_XHCI_USB +#ifndef CONFIG_TARGET_LX2162AQDS #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #endif +#endif /* FlexSPI */ #ifdef CONFIG_NXP_FSPI diff --git a/include/configs/lx2160aqds.h b/include/configs/lx2160aqds.h index 12884bcf2b..ea1b1635fe 100644 --- a/include/configs/lx2160aqds.h +++ b/include/configs/lx2160aqds.h @@ -8,70 +8,14 @@ #include "lx2160a_common.h" -/* Qixis */ -#define QIXIS_XMAP_MASK 0x07 -#define QIXIS_XMAP_SHIFT 5 -#define QIXIS_RST_CTL_RESET_EN 0x30 -#define QIXIS_LBMAP_DFLTBANK 0x00 -#define QIXIS_LBMAP_ALTBANK 0x20 -#define QIXIS_LBMAP_QSPI 0x00 -#define QIXIS_RCW_SRC_QSPI 0xff -#define QIXIS_RST_CTL_RESET 0x31 -#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 -#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 -#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 -#define QIXIS_LBMAP_MASK 0x0f -#define QIXIS_LBMAP_SD -#define QIXIS_LBMAP_EMMC -#define QIXIS_RCW_SRC_SD 0x08 -#define QIXIS_RCW_SRC_EMMC 0x09 -#define NON_EXTENDED_DUTCFG -#define QIXIS_SDID_MASK 0x07 -#define QIXIS_ESDHC_NO_ADAPTER 0x7 - -/* SYSCLK */ -#define QIXIS_SYSCLK_100 0x0 -#define QIXIS_SYSCLK_125 0x1 -#define QIXIS_SYSCLK_133 0x2 - -/* DDRCLK */ -#define QIXIS_DDRCLK_100 0x0 -#define QIXIS_DDRCLK_125 0x1 -#define QIXIS_DDRCLK_133 0x2 - -#define BRDCFG4_EMI1SEL_MASK 0xF8 -#define BRDCFG4_EMI1SEL_SHIFT 3 -#define BRDCFG4_EMI2SEL_MASK 0x07 -#define BRDCFG4_EMI2SEL_SHIFT 0 - /* VID */ - -#define I2C_MUX_CH_VOL_MONITOR 0xA -/* Voltage monitor on channel 2*/ -#define I2C_VOL_MONITOR_ADDR 0x63 -#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 -#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 -#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 #define CONFIG_VID_FLS_ENV "lx2160aqds_vdd_mv" #define CONFIG_VID - -/* The lowest and highest voltage allowed*/ -#define VDD_MV_MIN 775 -#define VDD_MV_MAX 925 - -/* PM Bus commands code for LTC3882*/ -#define PMBUS_CMD_PAGE 0x0 -#define PMBUS_CMD_READ_VOUT 0x8B -#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 -#define PMBUS_CMD_VOUT_COMMAND 0x21 -#define PWM_CHANNEL0 0x0 - #define CONFIG_VOL_MONITOR_LTC3882_SET #define CONFIG_VOL_MONITOR_LTC3882_READ /* RTC */ #define CONFIG_SYS_RTC_BUS_NUM 0 -#define I2C_MUX_CH_RTC 0xB /* * MMC @@ -87,25 +31,6 @@ u8 qixis_esdhc_detect_quirk(void); #if defined(CONFIG_FSL_MC_ENET) #define CONFIG_MII #define CONFIG_ETHPRIME "DPMAC17@rgmii-id" - -#define AQ_PHY_ADDR1 0x00 -#define AQ_PHY_ADDR2 0x01 -#define AQ_PHY_ADDR3 0x02 -#define AQ_PHY_ADDR4 0x03 - -#define CORTINA_PHY_ADDR1 0x0 - -#define INPHI_PHY_ADDR1 0x0 -#define INPHI_PHY_ADDR2 0x1 - -#define RGMII_PHY_ADDR1 0x01 -#define RGMII_PHY_ADDR2 0x02 - -#define SGMII_CARD_PORT1_PHY_ADDR 0x1C -#define SGMII_CARD_PORT2_PHY_ADDR 0x1D -#define SGMII_CARD_PORT3_PHY_ADDR 0x1E -#define SGMII_CARD_PORT4_PHY_ADDR 0x1F - #endif /* EEPROM */ diff --git a/include/configs/lx2160ardb.h b/include/configs/lx2160ardb.h index 59c2305a34..097f1224c9 100644 --- a/include/configs/lx2160ardb.h +++ b/include/configs/lx2160ardb.h @@ -8,47 +8,9 @@ #include "lx2160a_common.h" -/* Qixis */ -#define QIXIS_XMAP_MASK 0x07 -#define QIXIS_XMAP_SHIFT 5 -#define QIXIS_RST_CTL_RESET_EN 0x30 -#define QIXIS_LBMAP_DFLTBANK 0x00 -#define QIXIS_LBMAP_ALTBANK 0x20 -#define QIXIS_LBMAP_QSPI 0x00 -#define QIXIS_RCW_SRC_QSPI 0xff -#define QIXIS_RST_CTL_RESET 0x31 -#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 -#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 -#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 -#define QIXIS_LBMAP_MASK 0x0f -#define QIXIS_LBMAP_SD -#define QIXIS_LBMAP_EMMC -#define QIXIS_RCW_SRC_SD 0x08 -#define QIXIS_RCW_SRC_EMMC 0x09 -#define NON_EXTENDED_DUTCFG - /* VID */ - -#define I2C_MUX_CH_VOL_MONITOR 0xA -/* Voltage monitor on channel 2*/ -#define I2C_VOL_MONITOR_ADDR 0x63 -#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 -#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 -#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 #define CONFIG_VID_FLS_ENV "lx2160ardb_vdd_mv" #define CONFIG_VID - -/* The lowest and highest voltage allowed*/ -#define VDD_MV_MIN 775 -#define VDD_MV_MAX 855 - -/* PM Bus commands code for LTC3882*/ -#define PMBUS_CMD_PAGE 0x0 -#define PMBUS_CMD_READ_VOUT 0x8B -#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 -#define PMBUS_CMD_VOUT_COMMAND 0x21 -#define PWM_CHANNEL0 0x0 - #define CONFIG_VOL_MONITOR_LTC3882_SET #define CONFIG_VOL_MONITOR_LTC3882_READ @@ -59,17 +21,6 @@ #if defined(CONFIG_FSL_MC_ENET) #define CONFIG_MII #define CONFIG_ETHPRIME "DPMAC1@xgmii" - -#define AQR107_PHY_ADDR1 0x04 -#define AQR107_PHY_ADDR2 0x05 -#define AQR107_IRQ_MASK 0x0C - -#define CORTINA_PHY_ADDR1 0x0 -#define INPHI_PHY_ADDR1 0x0 - -#define RGMII_PHY_ADDR1 0x01 -#define RGMII_PHY_ADDR2 0x02 - #endif /* EMC2305 */ diff --git a/include/configs/lx2162aqds.h b/include/configs/lx2162aqds.h new file mode 100644 index 0000000000..847534c550 --- /dev/null +++ b/include/configs/lx2162aqds.h @@ -0,0 +1,78 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 NXP + */ + +#ifndef __LX2162_QDS_H +#define __LX2162_QDS_H + +#include "lx2160a_common.h" + +/* USB */ +#undef CONFIG_USB_MAX_CONTROLLER_COUNT +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 + +/* Voltage monitor on channel 2*/ +#define CONFIG_VID_FLS_ENV "lx2162aqds_vdd_mv" +#define CONFIG_VID +#define CONFIG_VOL_MONITOR_LTC3882_SET +#define CONFIG_VOL_MONITOR_LTC3882_READ + +/* RTC */ +#define CONFIG_SYS_RTC_BUS_NUM 0 + +/* + * MMC + */ +#ifdef CONFIG_MMC +#ifndef __ASSEMBLY__ +u8 qixis_esdhc_detect_quirk(void); +#endif +#define CONFIG_ESDHC_DETECT_QUIRK qixis_esdhc_detect_quirk() +#endif + +/* MAC/PHY configuration */ +#if defined(CONFIG_FSL_MC_ENET) +#define CONFIG_MII +#define CONFIG_ETHPRIME "DPMAC17@rgmii-id" +#endif + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + EXTRA_ENV_SETTINGS \ + "boot_scripts=lx2162aqds_boot.scr\0" \ + "boot_script_hdr=hdr_lx2162aqds_bs.out\0" \ + "BOARD=lx2162aqds\0" \ + "xspi_bootcmd=echo Trying load from flexspi..;" \ + "sf probe 0:0 && sf read $load_addr " \ + "$kernel_start $kernel_size ; env exists secureboot &&" \ + "sf read $kernelheader_addr_r $kernelheader_start " \ + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ + " bootm $load_addr#$BOARD\0" \ + "sd_bootcmd=echo Trying load from sd card..;" \ + "mmc dev 0; mmcinfo; mmc read $load_addr " \ + "$kernel_addr_sd $kernel_size_sd ;" \ + "env exists secureboot && mmc read $kernelheader_addr_r "\ + "$kernelhdr_addr_sd $kernelhdr_size_sd " \ + " && esbc_validate ${kernelheader_addr_r};" \ + "bootm $load_addr#$BOARD\0" \ + "emmc_bootcmd=echo Trying load from emmc card..;" \ + "mmc dev 1; mmcinfo; mmc read $load_addr " \ + "$kernel_addr_sd $kernel_size_sd ;" \ + "env exists secureboot && mmc read $kernelheader_addr_r "\ + "$kernelhdr_addr_sd $kernelhdr_size_sd " \ + " && esbc_validate ${kernelheader_addr_r};" \ + "bootm $load_addr#$BOARD\0" + +#include + +#endif /* __LX2162_QDS_H */