drivers: spl: consistently use the $(SPL_TPL_) macro

To simplify drivers/Makefile a bit when using TPL/SPL, we consistently
use the $(SPL_TPL_) macro to test for drivers that have separate
configuration symbols for the full U-boot, SPL and TPL stages.
Instead of explicitly repeating them in two separate if-guarded
sections of the Makefile, we can now simply list these options once.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit is contained in:
Philipp Tomsich 2017-07-04 11:29:55 +02:00
parent c3916e7bdb
commit 87c16d49a6

View File

@ -2,33 +2,34 @@
# SPDX-License-Identifier: GPL-2.0+ # SPDX-License-Identifier: GPL-2.0+
# #
obj-$(CONFIG_$(SPL_TPL_)DM) += core/ obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/
obj-$(CONFIG_$(SPL_)CLK) += clk/ obj-$(CONFIG_$(SPL_TPL_)DM) += core/
obj-$(CONFIG_$(SPL_)LED) += led/ obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
obj-$(CONFIG_$(SPL_)PHY) += phy/ obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/
obj-$(CONFIG_$(SPL_)PINCTRL) += pinctrl/ obj-$(CONFIG_$(SPL_TPL_)LED) += led/
obj-$(CONFIG_$(SPL_)RAM) += ram/ obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/
obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/
obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/
obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/
obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/
obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/
obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/
obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/
ifndef CONFIG_TPL_BUILD
ifdef CONFIG_SPL_BUILD ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/ obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/
obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/ obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/
obj-$(CONFIG_SPL_I2C_SUPPORT) += i2c/
obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/ obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/
obj-$(CONFIG_SPL_MMC_SUPPORT) += mmc/
obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/ obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/ obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/ obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/ obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/
obj-$(CONFIG_SPL_SERIAL_SUPPORT) += serial/
obj-$(CONFIG_SPL_SPI_SUPPORT) += spi/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/ obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/ obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/
obj-$(CONFIG_SPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/ obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/
obj-$(CONFIG_SPL_NAND_SUPPORT) += mtd/nand/
obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/ obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/
obj-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += mtd/spi/
obj-$(CONFIG_SPL_UBI) += mtd/ubispl/ obj-$(CONFIG_SPL_UBI) += mtd/ubispl/
obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/ obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/
obj-$(CONFIG_SPL_ETH_SUPPORT) += net/ obj-$(CONFIG_SPL_ETH_SUPPORT) += net/
@ -49,18 +50,13 @@ obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/
obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/ obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
obj-$(CONFIG_SPL_MMC_SUPPORT) += block/ obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
obj-$(CONFIG_SPL_FPGA_SUPPORT) += fpga/ obj-$(CONFIG_SPL_FPGA_SUPPORT) += fpga/
endif
endif endif
ifdef CONFIG_TPL_BUILD ifdef CONFIG_TPL_BUILD
obj-$(CONFIG_TPL_I2C_SUPPORT) += i2c/
obj-$(CONFIG_TPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
obj-$(CONFIG_TPL_MMC_SUPPORT) += mmc/
obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/ obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
obj-$(CONFIG_TPL_NAND_SUPPORT) += mtd/nand/
obj-$(CONFIG_TPL_SERIAL_SUPPORT) += serial/
obj-$(CONFIG_TPL_SPI_FLASH_SUPPORT) += mtd/spi/
obj-$(CONFIG_TPL_SPI_SUPPORT) += spi/
endif endif