From 015e3348fc3f0f20fd9286bf245e26212568ec93 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Sat, 28 Dec 2019 10:44:47 -0700 Subject: [PATCH] common: Drop floppy disk support This seems pretty old now. It has not been converted to driver model and is not used by any boards. Drop it. Signed-off-by: Simon Glass --- README | 26 -- cmd/Kconfig | 5 - cmd/Makefile | 1 - cmd/fdc.c | 752 -------------------------------- drivers/misc/Makefile | 1 - drivers/misc/ns87308.c | 100 ----- drivers/serial/serial_ns16550.c | 7 +- include/common.h | 1 - include/ns87308.h | 233 ---------- scripts/config_whitelist.txt | 34 -- 10 files changed, 1 insertion(+), 1159 deletions(-) delete mode 100644 cmd/fdc.c delete mode 100644 drivers/misc/ns87308.c delete mode 100644 include/ns87308.h diff --git a/README b/README index 91dfb24776..78f59c391a 100644 --- a/README +++ b/README @@ -2870,32 +2870,6 @@ Low Level (hardware related) configuration options: If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be forced to a value that ensures that CCSR is not relocated. -- Floppy Disk Support: - CONFIG_SYS_FDC_DRIVE_NUMBER - - the default drive number (default value 0) - - CONFIG_SYS_ISA_IO_STRIDE - - defines the spacing between FDC chipset registers - (default value 1) - - CONFIG_SYS_ISA_IO_OFFSET - - defines the offset of register from address. It - depends on which part of the data bus is connected to - the FDC chipset. (default value 0) - - If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and - CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their - default value. - - if CONFIG_SYS_FDC_HW_INIT is defined, then the function - fdc_hw_init() is called at the beginning of the FDC - setup. fdc_hw_init() must be provided by the board - source code. It is used to make hardware-dependent - initializations. - - CONFIG_IDE_AHB: Most IDE controllers were designed to be connected with PCI interface. Only few of them were designed for AHB interface. diff --git a/cmd/Kconfig b/cmd/Kconfig index 298feae24d..b1a1cbcab2 100644 --- a/cmd/Kconfig +++ b/cmd/Kconfig @@ -858,11 +858,6 @@ config CMD_FASTBOOT See doc/android/fastboot.txt for more information. -config CMD_FDC - bool "fdcboot - Boot from floppy device" - help - The 'fdtboot' command allows booting an image from a floppy disk. - config CMD_FLASH bool "flinfo, erase, protect" default y diff --git a/cmd/Makefile b/cmd/Makefile index ecf687d49f..6afdf65507 100644 --- a/cmd/Makefile +++ b/cmd/Makefile @@ -58,7 +58,6 @@ obj-$(CONFIG_HUSH_PARSER) += exit.o obj-$(CONFIG_CMD_EXT4) += ext4.o obj-$(CONFIG_CMD_EXT2) += ext2.o obj-$(CONFIG_CMD_FAT) += fat.o -obj-$(CONFIG_CMD_FDC) += fdc.o obj-$(CONFIG_CMD_FDT) += fdt.o obj-$(CONFIG_CMD_FITUPD) += fitupd.o obj-$(CONFIG_CMD_FLASH) += flash.o diff --git a/cmd/fdc.c b/cmd/fdc.c deleted file mode 100644 index 7d4b829637..0000000000 --- a/cmd/fdc.c +++ /dev/null @@ -1,752 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2001 - * Denis Peter, MPL AG, d.peter@mpl.ch. - */ -/* - * Floppy Disk support - */ - -#include -#include -#include -#include -#include - - -#undef FDC_DEBUG - -#ifdef FDC_DEBUG -#define PRINTF(fmt,args...) printf (fmt ,##args) -#else -#define PRINTF(fmt,args...) -#endif - -/*#if defined(CONFIG_CMD_DATE) */ -/*#include */ -/*#endif */ - -typedef struct { - int flags; /* connected drives ect */ - unsigned long blnr; /* Logical block nr */ - uchar drive; /* drive no */ - uchar cmdlen; /* cmd length */ - uchar cmd[16]; /* cmd desc */ - uchar dma; /* if > 0 dma enabled */ - uchar result[11]; /* status information */ - uchar resultlen; /* lenght of result */ -} FDC_COMMAND_STRUCT; - -/* flags: only the lower 8bit used: - * bit 0 if set drive 0 is present - * bit 1 if set drive 1 is present - * bit 2 if set drive 2 is present - * bit 3 if set drive 3 is present - * bit 4 if set disk in drive 0 is inserted - * bit 5 if set disk in drive 1 is inserted - * bit 6 if set disk in drive 2 is inserted - * bit 7 if set disk in drive 4 is inserted - */ - -/* cmd indexes */ -#define COMMAND 0 -#define DRIVE 1 -#define CONFIG0 1 -#define SPEC_HUTSRT 1 -#define TRACK 2 -#define CONFIG1 2 -#define SPEC_HLT 2 -#define HEAD 3 -#define CONFIG2 3 -#define SECTOR 4 -#define SECTOR_SIZE 5 -#define LAST_TRACK 6 -#define GAP 7 -#define DTL 8 -/* result indexes */ -#define STATUS_0 0 -#define STATUS_PCN 1 -#define STATUS_1 1 -#define STATUS_2 2 -#define STATUS_TRACK 3 -#define STATUS_HEAD 4 -#define STATUS_SECT 5 -#define STATUS_SECT_SIZE 6 - - -/* Register addresses */ -#define FDC_BASE 0x3F0 -#define FDC_SRA FDC_BASE + 0 /* Status Register A */ -#define FDC_SRB FDC_BASE + 1 /* Status Register B */ -#define FDC_DOR FDC_BASE + 2 /* Digital Output Register */ -#define FDC_TDR FDC_BASE + 3 /* Tape Drive Register */ -#define FDC_DSR FDC_BASE + 4 /* Data rate Register */ -#define FDC_MSR FDC_BASE + 4 /* Main Status Register */ -#define FDC_FIFO FDC_BASE + 5 /* FIFO */ -#define FDC_DIR FDC_BASE + 6 /* Digital Input Register */ -#define FDC_CCR FDC_BASE + 7 /* Configuration Control */ -/* Commands */ -#define FDC_CMD_SENSE_INT 0x08 -#define FDC_CMD_CONFIGURE 0x13 -#define FDC_CMD_SPECIFY 0x03 -#define FDC_CMD_RECALIBRATE 0x07 -#define FDC_CMD_READ 0x06 -#define FDC_CMD_READ_TRACK 0x02 -#define FDC_CMD_READ_ID 0x0A -#define FDC_CMD_DUMP_REG 0x0E -#define FDC_CMD_SEEK 0x0F - -#define FDC_CMD_SENSE_INT_LEN 0x01 -#define FDC_CMD_CONFIGURE_LEN 0x04 -#define FDC_CMD_SPECIFY_LEN 0x03 -#define FDC_CMD_RECALIBRATE_LEN 0x02 -#define FDC_CMD_READ_LEN 0x09 -#define FDC_CMD_READ_TRACK_LEN 0x09 -#define FDC_CMD_READ_ID_LEN 0x02 -#define FDC_CMD_DUMP_REG_LEN 0x01 -#define FDC_CMD_SEEK_LEN 0x03 - -#define FDC_FIFO_THR 0x0C -#define FDC_FIFO_DIS 0x00 -#define FDC_IMPLIED_SEEK 0x01 -#define FDC_POLL_DIS 0x00 -#define FDC_PRE_TRK 0x00 -#define FDC_CONFIGURE FDC_FIFO_THR | (FDC_POLL_DIS<<4) | (FDC_FIFO_DIS<<5) | (FDC_IMPLIED_SEEK << 6) -#define FDC_MFM_MODE 0x01 /* MFM enable */ -#define FDC_SKIP_MODE 0x00 /* skip enable */ - -#define FDC_TIME_OUT 100000 /* time out */ -#define FDC_RW_RETRIES 3 /* read write retries */ -#define FDC_CAL_RETRIES 3 /* calibration and seek retries */ - - -/* Disk structure */ -typedef struct { - unsigned int size; /* nr of sectors total */ - unsigned int sect; /* sectors per track */ - unsigned int head; /* nr of heads */ - unsigned int track; /* nr of tracks */ - unsigned int stretch; /* !=0 means double track steps */ - unsigned char gap; /* gap1 size */ - unsigned char rate; /* data rate. |= 0x40 for perpendicular */ - unsigned char spec1; /* stepping rate, head unload time */ - unsigned char fmt_gap;/* gap2 size */ - unsigned char hlt; /* head load time */ - unsigned char sect_code;/* Sector Size code */ - const char * name; /* used only for predefined formats */ -} FD_GEO_STRUCT; - - -/* supported Floppy types (currently only one) */ -const static FD_GEO_STRUCT floppy_type[2] = { - { 2880,18,2,80,0,0x1B,0x00,0xCF,0x6C,16,2,"H1440" }, /* 7 1.44MB 3.5" */ - { 0, 0,0, 0,0,0x00,0x00,0x00,0x00, 0,0,NULL }, /* end of table */ -}; - -static FDC_COMMAND_STRUCT cmd; /* global command struct */ - -/* If the boot drive number is undefined, we assume it's drive 0 */ -#ifndef CONFIG_SYS_FDC_DRIVE_NUMBER -#define CONFIG_SYS_FDC_DRIVE_NUMBER 0 -#endif - -/* Hardware access */ -#ifndef CONFIG_SYS_ISA_IO_STRIDE -#define CONFIG_SYS_ISA_IO_STRIDE 1 -#endif - -#ifndef CONFIG_SYS_ISA_IO_OFFSET -#define CONFIG_SYS_ISA_IO_OFFSET 0 -#endif - -/* Supporting Functions */ -/* reads a Register of the FDC */ -unsigned char read_fdc_reg(unsigned int addr) -{ - volatile unsigned char *val = - (volatile unsigned char *)(CONFIG_SYS_ISA_IO_BASE_ADDRESS + - (addr * CONFIG_SYS_ISA_IO_STRIDE) + - CONFIG_SYS_ISA_IO_OFFSET); - - return val [0]; -} - -/* writes a Register of the FDC */ -void write_fdc_reg(unsigned int addr, unsigned char val) -{ - volatile unsigned char *tmp = - (volatile unsigned char *)(CONFIG_SYS_ISA_IO_BASE_ADDRESS + - (addr * CONFIG_SYS_ISA_IO_STRIDE) + - CONFIG_SYS_ISA_IO_OFFSET); - tmp[0]=val; -} - -/* waits for an interrupt (polling) */ -int wait_for_fdc_int(void) -{ - unsigned long timeout; - timeout = FDC_TIME_OUT; - while((read_fdc_reg(FDC_SRA)&0x80)==0) { - timeout--; - udelay(10); - if(timeout==0) /* timeout occurred */ - return false; - } - return true; -} - -/* reads a byte from the FIFO of the FDC and checks direction and RQM bit - of the MSR. returns -1 if timeout, or byte if ok */ -int read_fdc_byte(void) -{ - unsigned long timeout; - timeout = FDC_TIME_OUT; - while((read_fdc_reg(FDC_MSR)&0xC0)!=0xC0) { - /* direction out and ready */ - udelay(10); - timeout--; - if(timeout==0) /* timeout occurred */ - return -1; - } - return read_fdc_reg(FDC_FIFO); -} - -/* if the direction of the FIFO is wrong, this routine is used to - empty the FIFO. Should _not_ be used */ -int fdc_need_more_output(void) -{ - unsigned char c; - while((read_fdc_reg(FDC_MSR)&0xC0)==0xC0) { - c=(unsigned char)read_fdc_byte(); - printf("Error: more output: %x\n",c); - } - return true; -} - - -/* writes a byte to the FIFO of the FDC and checks direction and RQM bit - of the MSR */ -int write_fdc_byte(unsigned char val) -{ - unsigned long timeout; - timeout = FDC_TIME_OUT; - while((read_fdc_reg(FDC_MSR)&0xC0)!=0x80) { - /* direction in and ready for byte */ - timeout--; - udelay(10); - fdc_need_more_output(); - if(timeout==0) /* timeout occurred */ - return false; - } - write_fdc_reg(FDC_FIFO,val); - return true; -} - -/* sets up all FDC commands and issues it to the FDC. If - the command causes direct results (no Execution Phase) - the result is be read as well. */ - -int fdc_issue_cmd(FDC_COMMAND_STRUCT *pCMD,FD_GEO_STRUCT *pFG) -{ - int i; - unsigned long head,track,sect,timeout; - track = pCMD->blnr / (pFG->sect * pFG->head); /* track nr */ - sect = pCMD->blnr % (pFG->sect * pFG->head); /* remaining blocks */ - head = sect / pFG->sect; /* head nr */ - sect = sect % pFG->sect; /* remaining blocks */ - sect++; /* sectors are 1 based */ - PRINTF("Cmd 0x%02x Track %ld, Head %ld, Sector %ld, Drive %d (blnr %ld)\n", - pCMD->cmd[0],track,head,sect,pCMD->drive,pCMD->blnr); - - if(head|=0) { /* max heads = 2 */ - pCMD->cmd[DRIVE]=pCMD->drive | 0x04; /* head 1 */ - pCMD->cmd[HEAD]=(unsigned char) head; /* head register */ - } - else { - pCMD->cmd[DRIVE]=pCMD->drive; /* head 0 */ - pCMD->cmd[HEAD]=(unsigned char) head; /* head register */ - } - pCMD->cmd[TRACK]=(unsigned char) track; /* track */ - switch (pCMD->cmd[COMMAND]) { - case FDC_CMD_READ: - pCMD->cmd[SECTOR]=(unsigned char) sect; /* sector */ - pCMD->cmd[SECTOR_SIZE]=pFG->sect_code; /* sector size code */ - pCMD->cmd[LAST_TRACK]=pFG->sect; /* End of track */ - pCMD->cmd[GAP]=pFG->gap; /* gap */ - pCMD->cmd[DTL]=0xFF; /* DTL */ - pCMD->cmdlen=FDC_CMD_READ_LEN; - pCMD->cmd[COMMAND]|=(FDC_MFM_MODE<<6); /* set MFM bit */ - pCMD->cmd[COMMAND]|=(FDC_SKIP_MODE<<5); /* set Skip bit */ - pCMD->resultlen=0; /* result only after execution */ - break; - case FDC_CMD_SEEK: - pCMD->cmdlen=FDC_CMD_SEEK_LEN; - pCMD->resultlen=0; /* no result */ - break; - case FDC_CMD_CONFIGURE: - pCMD->cmd[CONFIG0]=0; - pCMD->cmd[CONFIG1]=FDC_CONFIGURE; /* FIFO Threshold, Poll, Enable FIFO */ - pCMD->cmd[CONFIG2]=FDC_PRE_TRK; /* Precompensation Track */ - pCMD->cmdlen=FDC_CMD_CONFIGURE_LEN; - pCMD->resultlen=0; /* no result */ - break; - case FDC_CMD_SPECIFY: - pCMD->cmd[SPEC_HUTSRT]=pFG->spec1; - pCMD->cmd[SPEC_HLT]=(pFG->hlt)<<1; /* head load time */ - if(pCMD->dma==0) - pCMD->cmd[SPEC_HLT]|=0x1; /* no dma */ - pCMD->cmdlen=FDC_CMD_SPECIFY_LEN; - pCMD->resultlen=0; /* no result */ - break; - case FDC_CMD_DUMP_REG: - pCMD->cmdlen=FDC_CMD_DUMP_REG_LEN; - pCMD->resultlen=10; /* 10 byte result */ - break; - case FDC_CMD_READ_ID: - pCMD->cmd[COMMAND]|=(FDC_MFM_MODE<<6); /* set MFM bit */ - pCMD->cmdlen=FDC_CMD_READ_ID_LEN; - pCMD->resultlen=7; /* 7 byte result */ - break; - case FDC_CMD_RECALIBRATE: - pCMD->cmd[DRIVE]&=0x03; /* don't set the head bit */ - pCMD->cmdlen=FDC_CMD_RECALIBRATE_LEN; - pCMD->resultlen=0; /* no result */ - break; - break; - case FDC_CMD_SENSE_INT: - pCMD->cmdlen=FDC_CMD_SENSE_INT_LEN; - pCMD->resultlen=2; - break; - } - for(i=0;icmdlen;i++) { - /* PRINTF("write cmd%d = 0x%02X\n",i,pCMD->cmd[i]); */ - if (write_fdc_byte(pCMD->cmd[i]) == false) { - PRINTF("Error: timeout while issue cmd%d\n",i); - return false; - } - } - timeout=FDC_TIME_OUT; - for(i=0;iresultlen;i++) { - while((read_fdc_reg(FDC_MSR)&0xC0)!=0xC0) { - timeout--; - if(timeout==0) { - PRINTF(" timeout while reading result%d MSR=0x%02X\n",i,read_fdc_reg(FDC_MSR)); - return false; - } - } - pCMD->result[i]=(unsigned char)read_fdc_byte(); - } - return true; -} - -/* selects the drive assigned in the cmd structur and - switches on the Motor */ -void select_fdc_drive(FDC_COMMAND_STRUCT *pCMD) -{ - unsigned char val; - - val=(1<<(4+pCMD->drive))|pCMD->drive|0xC; /* set reset, dma gate and motor bits */ - if((read_fdc_reg(FDC_DOR)&val)!=val) { - write_fdc_reg(FDC_DOR,val); - for(val=0;val<255;val++) - udelay(500); /* wait some time to start motor */ - } -} - -/* switches off the Motor of the specified drive */ -void stop_fdc_drive(FDC_COMMAND_STRUCT *pCMD) -{ - unsigned char val; - - val=(1<<(4+pCMD->drive))|pCMD->drive; /* sets motor bits */ - write_fdc_reg(FDC_DOR,(read_fdc_reg(FDC_DOR)&~val)); -} - -/* issues a recalibrate command, waits for interrupt and - * issues a sense_interrupt */ -int fdc_recalibrate(FDC_COMMAND_STRUCT *pCMD,FD_GEO_STRUCT *pFG) -{ - pCMD->cmd[COMMAND]=FDC_CMD_RECALIBRATE; - if (fdc_issue_cmd(pCMD, pFG) == false) - return false; - while (wait_for_fdc_int() != true); - - pCMD->cmd[COMMAND]=FDC_CMD_SENSE_INT; - return(fdc_issue_cmd(pCMD,pFG)); -} - -/* issues a recalibrate command, waits for interrupt and - * issues a sense_interrupt */ -int fdc_seek(FDC_COMMAND_STRUCT *pCMD,FD_GEO_STRUCT *pFG) -{ - pCMD->cmd[COMMAND]=FDC_CMD_SEEK; - if (fdc_issue_cmd(pCMD, pFG) == false) - return false; - while (wait_for_fdc_int() != true); - - pCMD->cmd[COMMAND]=FDC_CMD_SENSE_INT; - return(fdc_issue_cmd(pCMD,pFG)); -} - -/* terminates current command, by not servicing the FIFO - * waits for interrupt and fills in the result bytes */ -int fdc_terminate(FDC_COMMAND_STRUCT *pCMD) -{ - int i; - for(i=0;i<100;i++) - udelay(500); /* wait 500usec for fifo overrun */ - while((read_fdc_reg(FDC_SRA)&0x80)==0x00); /* wait as long as no int has occurred */ - for(i=0;i<7;i++) { - pCMD->result[i]=(unsigned char)read_fdc_byte(); - } - return true; -} - -/* reads data from FDC, seek commands are issued automatic */ -int fdc_read_data(unsigned char *buffer, unsigned long blocks,FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG) -{ - /* first seek to start address */ - unsigned long len,readblk,i,timeout,ii,offset; - unsigned char c,retriesrw,retriescal; - unsigned char *bufferw; /* working buffer */ - int sect_size; - int flags; - - flags=disable_interrupts(); /* switch off all Interrupts */ - select_fdc_drive(pCMD); /* switch on drive */ - sect_size=0x080<sect_code; - retriesrw=0; - retriescal=0; - offset=0; - if (fdc_seek(pCMD, pFG) == false) { - stop_fdc_drive(pCMD); - if (flags) - enable_interrupts(); - return false; - } - if((pCMD->result[STATUS_0]&0x20)!=0x20) { - printf("Seek error Status: %02X\n",pCMD->result[STATUS_0]); - stop_fdc_drive(pCMD); - if (flags) - enable_interrupts(); - return false; - } - /* now determine the next seek point */ - /* lastblk=pCMD->blnr + blocks; */ - /* readblk=(pFG->head*pFG->sect)-(pCMD->blnr%(pFG->head*pFG->sect)); */ - readblk=pFG->sect-(pCMD->blnr%pFG->sect); - PRINTF("1st nr of block possible read %ld start %ld\n",readblk,pCMD->blnr); - if(readblk>blocks) /* is end within 1st track */ - readblk=blocks; /* yes, correct it */ - PRINTF("we read %ld blocks start %ld\n",readblk,pCMD->blnr); - bufferw = &buffer[0]; /* setup working buffer */ - do { -retryrw: - len=sect_size * readblk; - pCMD->cmd[COMMAND]=FDC_CMD_READ; - if (fdc_issue_cmd(pCMD, pFG) == false) { - stop_fdc_drive(pCMD); - if (flags) - enable_interrupts(); - return false; - } - for (i=0;i6) { - for(ii=0;ii<7;ii++) { - pCMD->result[ii]=bufferw[(i-7+ii)]; - } /* for */ - } - if(retriesrw++>FDC_RW_RETRIES) { - if (retriescal++>FDC_CAL_RETRIES) { - stop_fdc_drive(pCMD); - if (flags) - enable_interrupts(); - return false; - } - else { - PRINTF(" trying to recalibrate Try %d\n",retriescal); - if (fdc_recalibrate(pCMD, pFG) == false) { - stop_fdc_drive(pCMD); - if (flags) - enable_interrupts(); - return false; - } - retriesrw=0; - goto retrycal; - } /* else >FDC_CAL_RETRIES */ - } - else { - PRINTF("Read retry %d\n",retriesrw); - goto retryrw; - } /* else >FDC_RW_RETRIES */ - }/* if output */ - timeout--; - } while (true); - } /* for len */ - /* the last sector of a track or all data has been read, - * we need to get the results */ - fdc_terminate(pCMD); - offset+=(sect_size*readblk); /* set up buffer pointer */ - bufferw = &buffer[offset]; - pCMD->blnr+=readblk; /* update current block nr */ - blocks-=readblk; /* update blocks */ - if(blocks==0) - break; /* we are finish */ - /* setup new read blocks */ - /* readblk=pFG->head*pFG->sect; */ - readblk=pFG->sect; - if(readblk>blocks) - readblk=blocks; -retrycal: - /* a seek is necessary */ - if (fdc_seek(pCMD, pFG) == false) { - stop_fdc_drive(pCMD); - if (flags) - enable_interrupts(); - return false; - } - if((pCMD->result[STATUS_0]&0x20)!=0x20) { - PRINTF("Seek error Status: %02X\n",pCMD->result[STATUS_0]); - stop_fdc_drive(pCMD); - return false; - } - } while (true); /* start over */ - stop_fdc_drive(pCMD); /* switch off drive */ - if (flags) - enable_interrupts(); - return true; -} - -/* Scan all drives and check if drive is present and disk is inserted */ -int fdc_check_drive(FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG) -{ - int i,drives,state; - /* OK procedure of data book is satisfied. - * trying to get some information over the drives */ - state=0; /* no drives, no disks */ - for(drives=0;drives<4;drives++) { - pCMD->drive=drives; - select_fdc_drive(pCMD); - pCMD->blnr=0; /* set to the 1st block */ - if (fdc_recalibrate(pCMD, pFG) == false) - continue; - if((pCMD->result[STATUS_0]&0x10)==0x10) - continue; - /* ok drive connected check for disk */ - state|=(1<blnr=pFG->size; /* set to the last block */ - if (fdc_seek(pCMD, pFG) == false) - continue; - pCMD->blnr=0; /* set to the 1st block */ - if (fdc_recalibrate(pCMD, pFG) == false) - continue; - pCMD->cmd[COMMAND]=FDC_CMD_READ_ID; - if (fdc_issue_cmd(pCMD, pFG) == false) - continue; - state|=(0x10<name : ""); - } - pCMD->flags=state; - return true; -} - - -/************************************************************************** -* int fdc_setup -* setup the fdc according the datasheet -* assuming in PS2 Mode -*/ -int fdc_setup(int drive, FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG) -{ - int i; - -#ifdef CONFIG_SYS_FDC_HW_INIT - fdc_hw_init (); -#endif - /* first, we reset the FDC via the DOR */ - write_fdc_reg(FDC_DOR,0x00); - for(i=0; i<255; i++) /* then we wait some time */ - udelay(500); - /* then, we clear the reset in the DOR */ - pCMD->drive=drive; - select_fdc_drive(pCMD); - /* initialize the CCR */ - write_fdc_reg(FDC_CCR,pFG->rate); - /* then initialize the DSR */ - write_fdc_reg(FDC_DSR,pFG->rate); - if (wait_for_fdc_int() == false) { - PRINTF("Time Out after writing CCR\n"); - return false; - } - /* now issue sense Interrupt and status command - * assuming only one drive present (drive 0) */ - pCMD->dma=0; /* we don't use any dma at all */ - for(i=0;i<4;i++) { - /* issue sense interrupt for all 4 possible drives */ - pCMD->cmd[COMMAND]=FDC_CMD_SENSE_INT; - if (fdc_issue_cmd(pCMD, pFG) == false) { - PRINTF("Sense Interrupt for drive %d failed\n",i); - } - } - /* issue the configure command */ - pCMD->drive=drive; - select_fdc_drive(pCMD); - pCMD->cmd[COMMAND]=FDC_CMD_CONFIGURE; - if (fdc_issue_cmd(pCMD, pFG) == false) { - PRINTF(" configure timeout\n"); - stop_fdc_drive(pCMD); - return false; - } - /* issue specify command */ - pCMD->cmd[COMMAND]=FDC_CMD_SPECIFY; - if (fdc_issue_cmd(pCMD, pFG) == false) { - PRINTF(" specify timeout\n"); - stop_fdc_drive(pCMD); - return false; - - } - /* then, we clear the reset in the DOR */ - /* fdc_check_drive(pCMD,pFG); */ - /* write_fdc_reg(FDC_DOR,0x04); */ - - return true; -} - -/**************************************************************************** - * main routine do_fdcboot - */ -int do_fdcboot (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - FD_GEO_STRUCT *pFG = (FD_GEO_STRUCT *)floppy_type; - FDC_COMMAND_STRUCT *pCMD = &cmd; - unsigned long addr,imsize; -#if defined(CONFIG_LEGACY_IMAGE_FORMAT) - image_header_t *hdr; /* used for fdc boot */ -#endif - unsigned char boot_drive; - int i,nrofblk; -#if defined(CONFIG_FIT) - const void *fit_hdr = NULL; -#endif - - switch (argc) { - case 1: - addr = CONFIG_SYS_LOAD_ADDR; - boot_drive=CONFIG_SYS_FDC_DRIVE_NUMBER; - break; - case 2: - addr = simple_strtoul(argv[1], NULL, 16); - boot_drive=CONFIG_SYS_FDC_DRIVE_NUMBER; - break; - case 3: - addr = simple_strtoul(argv[1], NULL, 16); - boot_drive=simple_strtoul(argv[2], NULL, 10); - break; - default: - return CMD_RET_USAGE; - } - /* setup FDC and scan for drives */ - if (fdc_setup(boot_drive, pCMD, pFG) == false) { - printf("\n** Error in setup FDC **\n"); - return 1; - } - if (fdc_check_drive(pCMD, pFG) == false) { - printf("\n** Error in check_drives **\n"); - return 1; - } - if((pCMD->flags&(1<flags&(0x10<drive=boot_drive; - /* read first block */ - pCMD->blnr=0; - if (fdc_read_data((unsigned char *)addr, 1, pCMD, pFG) == false) { - printf("\nRead error:"); - for(i=0;i<7;i++) - printf("result%d: 0x%02X\n",i,pCMD->result[i]); - return 1; - } - - switch (genimg_get_format ((void *)addr)) { -#if defined(CONFIG_LEGACY_IMAGE_FORMAT) - case IMAGE_FORMAT_LEGACY: - hdr = (image_header_t *)addr; - image_print_contents (hdr); - - imsize = image_get_image_size (hdr); - break; -#endif -#if defined(CONFIG_FIT) - case IMAGE_FORMAT_FIT: - fit_hdr = (const void *)addr; - puts ("Fit image detected...\n"); - - imsize = fit_get_size (fit_hdr); - break; -#endif - default: - puts ("** Unknown image type\n"); - return 1; - } - - nrofblk=imsize/512; - if((imsize%512)>0) - nrofblk++; - printf("Loading %ld Bytes (%d blocks) at 0x%08lx..\n",imsize,nrofblk,addr); - pCMD->blnr=0; - if (fdc_read_data((unsigned char *)addr, nrofblk, pCMD, pFG) == false) { - /* read image block */ - printf("\nRead error:"); - for(i=0;i<7;i++) - printf("result%d: 0x%02X\n",i,pCMD->result[i]); - return 1; - } - printf("OK %ld Bytes loaded.\n",imsize); - - flush_cache (addr, imsize); - -#if defined(CONFIG_FIT) - /* This cannot be done earlier, we need complete FIT image in RAM first */ - if (genimg_get_format ((void *)addr) == IMAGE_FORMAT_FIT) { - if (!fit_check_format (fit_hdr)) { - puts ("** Bad FIT image format\n"); - return 1; - } - fit_print_contents (fit_hdr); - } -#endif - - /* Loading ok, update default load address */ - load_addr = addr; - - return bootm_maybe_autostart(cmdtp, argv[0]); -} - -U_BOOT_CMD( - fdcboot, 3, 1, do_fdcboot, - "boot from floppy device", - "loadAddr drive" -); diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index d4e8638dea..2b843de93c 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -51,7 +51,6 @@ obj-$(CONFIG_LED_STATUS_GPIO) += gpio_led.o obj-$(CONFIG_MPC83XX_SERDES) += mpc83xx_serdes.o obj-$(CONFIG_MXC_OCOTP) += mxc_ocotp.o obj-$(CONFIG_MXS_OCOTP) += mxs_ocotp.o -obj-$(CONFIG_NS87308) += ns87308.o obj-$(CONFIG_NUVOTON_NCT6102D) += nuvoton_nct6102d.o obj-$(CONFIG_P2SB) += p2sb-uclass.o obj-$(CONFIG_PCA9551_LED) += pca9551_led.o diff --git a/drivers/misc/ns87308.c b/drivers/misc/ns87308.c deleted file mode 100644 index f5de3329b7..0000000000 --- a/drivers/misc/ns87308.c +++ /dev/null @@ -1,100 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000 - * Rob Taylor, Flying Pig Systems. robt@flyingpig.com. - */ - -#include - -#include - -void initialise_ns87308 (void) -{ -#ifdef CONFIG_SYS_NS87308_PS2MOD - unsigned char data; - - /* - * Switch floppy drive to PS/2 mode. - */ - read_pnp_config(SUPOERIO_CONF1, &data); - data &= 0xFB; - write_pnp_config(SUPOERIO_CONF1, data); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_KBC1) - PNP_SET_DEVICE_BASE(LDEV_KBC1, CONFIG_SYS_NS87308_KBC1_BASE); - write_pnp_config(LUN_CONFIG_REG, 0); - write_pnp_config(CBASE_HIGH, 0x00); - write_pnp_config(CBASE_LOW, 0x64); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_MOUSE) - PNP_ACTIVATE_DEVICE(LDEV_MOUSE); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_RTC_APC) - PNP_SET_DEVICE_BASE(LDEV_RTC_APC, CONFIG_SYS_NS87308_RTC_BASE); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_FDC) - PNP_SET_DEVICE_BASE(LDEV_FDC, CONFIG_SYS_NS87308_FDC_BASE); - write_pnp_config(LUN_CONFIG_REG, 0x40); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_RARP) - PNP_SET_DEVICE_BASE(LDEV_PARP, CONFIG_SYS_NS87308_LPT_BASE); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_UART1) - PNP_SET_DEVICE_BASE(LDEV_UART1, CONFIG_SYS_NS87308_UART1_BASE); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_UART2) - PNP_SET_DEVICE_BASE(LDEV_UART2, CONFIG_SYS_NS87308_UART2_BASE); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_GPIO) - PNP_SET_DEVICE_BASE(LDEV_GPIO, CONFIG_SYS_NS87308_GPIO_BASE); -#endif - -#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_POWRMAN) -#ifndef CONFIG_SYS_NS87308_PWMAN_BASE - PNP_ACTIVATE_DEVICE(LDEV_POWRMAN); -#else - PNP_SET_DEVICE_BASE(LDEV_POWRMAN, CONFIG_SYS_NS87308_PWMAN_BASE); - - /* - * Enable all units - */ - write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_FER1, 0x7d); - write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_FER2, 0x87); - -#ifdef CONFIG_SYS_NS87308_PMC1 - write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_PMC1, CONFIG_SYS_NS87308_PMC1); -#endif - -#ifdef CONFIG_SYS_NS87308_PMC2 - write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_PMC2, CONFIG_SYS_NS87308_PMC2); -#endif - -#ifdef CONFIG_SYS_NS87308_PMC3 - write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_PMC3, CONFIG_SYS_NS87308_PMC3); -#endif -#endif -#endif - -#ifdef CONFIG_SYS_NS87308_CS0_BASE - PNP_PGCS_CSLINE_BASE(0, CONFIG_SYS_NS87308_CS0_BASE); - PNP_PGCS_CSLINE_CONF(0, CONFIG_SYS_NS87308_CS0_CONF); -#endif - -#ifdef CONFIG_SYS_NS87308_CS1_BASE - PNP_PGCS_CSLINE_BASE(1, CONFIG_SYS_NS87308_CS1_BASE); - PNP_PGCS_CSLINE_CONF(1, CONFIG_SYS_NS87308_CS1_CONF); -#endif - -#ifdef CONFIG_SYS_NS87308_CS2_BASE - PNP_PGCS_CSLINE_BASE(2, CONFIG_SYS_NS87308_CS2_BASE); - PNP_PGCS_CSLINE_CONF(2, CONFIG_SYS_NS87308_CS2_CONF); -#endif -} diff --git a/drivers/serial/serial_ns16550.c b/drivers/serial/serial_ns16550.c index 5afe620b9f..a1069f92a6 100644 --- a/drivers/serial/serial_ns16550.c +++ b/drivers/serial/serial_ns16550.c @@ -5,14 +5,9 @@ */ #include -#include - #include -#ifdef CONFIG_NS87308 -#include -#endif - #include +#include #ifndef CONFIG_NS16550_MIN_FUNCTIONS diff --git a/include/common.h b/include/common.h index 6b7b199ab4..1bd42299bc 100644 --- a/include/common.h +++ b/include/common.h @@ -89,7 +89,6 @@ phys_size_t get_effective_memsize(void); /* $(BOARD)/$(BOARD).c */ void reset_phy (void); -void fdc_hw_init (void); #if !defined(CONFIG_ENV_EEPROM_IS_ON_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR) # define CONFIG_SYS_DEF_EEPROM_ADDR CONFIG_SYS_I2C_EEPROM_ADDR diff --git a/include/ns87308.h b/include/ns87308.h deleted file mode 100644 index d5ccd3ba3b..0000000000 --- a/include/ns87308.h +++ /dev/null @@ -1,233 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2000 - * Rob Taylor, Flying Pig Systems. robt@flyingpig.com. - */ - -#ifndef _NS87308_H_ -#define _NS87308_H_ - -#include - -/* Note: I couldn't find a full data sheet for the ns87308, but the ns87307 seems to be pretty - functionally- (and pin-) equivalent to the 87308, but the 308 has better ir support. */ - -void initialise_ns87308(void); - -/* - * The following struct represents the GPIO registers on the NS87308/NS97307 - */ -struct GPIO -{ - unsigned char dta1; /* 0 data port 1 */ - unsigned char dir1; /* 1 direction port 1 */ - unsigned char out1; /* 2 output type port 1 */ - unsigned char puc1; /* 3 pull-up control port 1 */ - unsigned char dta2; /* 4 data port 2 */ - unsigned char dir2; /* 5 direction port 2 */ - unsigned char out2; /* 6 output type port 2 */ - unsigned char puc2; /* 7 pull-up control port 2 */ -}; - -/* - * The following represents the power management registers on the NS87308/NS97307 - */ -#define PWM_FER1 0 /* 0 function enable reg. 1 */ -#define PWM_FER2 1 /* 1 function enable reg. 2 */ -#define PWM_PMC1 2 /* 2 power mgmt. control 1 */ -#define PWM_PMC2 3 /* 3 power mgmt. control 2 */ -#define PWM_PMC3 4 /* 4 power mgmt. control 3 */ -#define PWM_WDTO 5 /* 5 watchdog time-out */ -#define PWM_WDCF 6 /* 6 watchdog config. */ -#define PWM_WDST 7 /* 7 watchdog status */ - -/*PNP config registers: - * these depend on the stated of BADDR1 and BADDR0 on startup - * so there's three versions here with the last two digits indicating - * for which configuration their valid - * the 1st of the two digits indicates the state of BADDR1 - * the 2st of the two digits indicates the state of BADDR0 - */ - - -#define IO_INDEX_OFFSET_0x 0x0279 /* full PnP isa Mode */ -#define IO_INDEX_OFFSET_10 0x015C /* PnP motherboard mode */ -#define IO_INDEX_OFFSET_11 0x002E /* PnP motherboard mode */ -#define IO_DATA_OFFSET_0x 0x0A79 /* full PnP isa Mode */ -#define IO_DATA_OFFSET_10 0x015D /* PnP motherboard mode */ -#define IO_DATA_OFFSET_11 0x002F /* PnP motherboard mode */ - -#if defined(CONFIG_SYS_NS87308_BADDR_0x) -#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_0x) -#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_0x) -#elif defined(CONFIG_SYS_NS87308_BADDR_10) -#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_10) -#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_10) -#elif defined(CONFIG_SYS_NS87308_BADDR_11) -#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_11) -#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_11) -#endif - -/* PnP register definitions */ - -#define SET_RD_DATA_PORT 0x00 -#define SERIAL_ISOLATION 0x01 -#define CONFIG_CONTROL 0x02 -#define WAKE_CSN 0x03 -#define RES_DATA 0x04 -#define STATUS 0x05 -#define SET_CSN 0x06 -#define LOGICAL_DEVICE 0x07 - -/*vendor defined values */ -#define SID_REG 0x20 -#define SUPOERIO_CONF1 0x21 -#define SUPOERIO_CONF2 0x22 -#define PGCS_INDEX 0x23 -#define PGCS_DATA 0x24 - -/* values above 30 are different for each logical device - but I can't be arsed to enter them all. the ones here - are pretty consistent between all logical devices - feel free to correct the situation if you want.. ;) - */ -#define ACTIVATE 0x30 -#define ACTIVATE_OFF 0x00 -#define ACTIVATE_ON 0x01 - -#define BASE_ADDR_HIGH 0x60 -#define BASE_ADDR_LOW 0x61 -#define LUN_CONFIG_REG 0xF0 -#define DBASE_HIGH 0x60 /* SIO KBC data base address, 15:8 */ -#define DBASE_LOW 0x61 /* SIO KBC data base address, 7:0 */ -#define CBASE_HIGH 0x62 /* SIO KBC command base addr, 15:8 */ -#define CBASE_LOW 0x63 /* SIO KBC command base addr, 7:0 */ - -/* the logical devices*/ -#define LDEV_KBC1 0x00 /* 2 devices for keyboard and mouse controller*/ -#define LDEV_KBC2 0x01 -#define LDEV_MOUSE 0x01 -#define LDEV_RTC_APC 0x02 /*Real Time Clock and Advanced Power Control*/ -#define LDEV_FDC 0x03 /*floppy disk controller*/ -#define LDEV_PARP 0x04 /*Parallel port*/ -#define LDEV_UART2 0x05 -#define LDEV_UART1 0x06 -#define LDEV_GPIO 0x07 /*General Purpose IO and chip select output signals*/ -#define LDEV_POWRMAN 0x08 /*Power Managment*/ - -#define CONFIG_SYS_NS87308_KBC1 (1 << LDEV_KBC1) -#define CONFIG_SYS_NS87308_KBC2 (1 << LDEV_KBC2) -#define CONFIG_SYS_NS87308_MOUSE (1 << LDEV_MOUSE) -#define CONFIG_SYS_NS87308_RTC_APC (1 << LDEV_RTC_APC) -#define CONFIG_SYS_NS87308_FDC (1 << LDEV_FDC) -#define CONFIG_SYS_NS87308_PARP (1 << LDEV_PARP) -#define CONFIG_SYS_NS87308_UART2 (1 << LDEV_UART2) -#define CONFIG_SYS_NS87308_UART1 (1 << LDEV_UART1) -#define CONFIG_SYS_NS87308_GPIO (1 << LDEV_GPIO) -#define CONFIG_SYS_NS87308_POWRMAN (1 << LDEV_POWRMAN) - -/*some functions and macro's for doing configuration */ - -static inline void read_pnp_config(unsigned char index, unsigned char *data) -{ - pci_writeb(index,IO_INDEX); - pci_readb(IO_DATA, *data); -} - -static inline void write_pnp_config(unsigned char index, unsigned char data) -{ - pci_writeb(index,IO_INDEX); - pci_writeb(data, IO_DATA); -} - -static inline void pnp_set_device(unsigned char dev) -{ - write_pnp_config(LOGICAL_DEVICE, dev); -} - -static inline void write_pm_reg(unsigned short base, unsigned char index, unsigned char data) -{ - pci_writeb(index, CONFIG_SYS_ISA_IO + base); - eieio(); - pci_writeb(data, CONFIG_SYS_ISA_IO + base + 1); -} - -/*void write_pnp_config(unsigned char index, unsigned char data); -void pnp_set_device(unsigned char dev); -*/ - -#define PNP_SET_DEVICE_BASE(dev,base) \ - pnp_set_device(dev); \ - write_pnp_config(ACTIVATE, ACTIVATE_OFF); \ - write_pnp_config(BASE_ADDR_HIGH, ((base) >> 8) & 0xff ); \ - write_pnp_config(BASE_ADDR_LOW, (base) &0xff); \ - write_pnp_config(ACTIVATE, ACTIVATE_ON); - -#define PNP_ACTIVATE_DEVICE(dev) \ - pnp_set_device(dev); \ - write_pnp_config(ACTIVATE, ACTIVATE_ON); - -#define PNP_DEACTIVATE_DEVICE(dev) \ - pnp_set_device(dev); \ - write_pnp_config(ACTIVATE, ACTIVATE_OFF); - - -static inline void write_pgcs_config(unsigned char index, unsigned char data) -{ - write_pnp_config(PGCS_INDEX, index); - write_pnp_config(PGCS_DATA, data); -} - -/* these macrose configure the 3 CS lines - on the sandpoint board these controll NVRAM - CS0 is connected to NVRAMCS - CS1 is connected to NVRAMAS0 - CS2 is connected to NVRAMAS1 - */ -#define PGCS_CS_ASSERT_ON_WRITE 0x10 -#define PGCS_CS_ASSERT_ON_READ 0x20 - -#define PNP_PGCS_CSLINE_BASE(cs, base) \ - write_pgcs_config((cs) << 2, ((base) >> 8) & 0xff ); \ - write_pgcs_config(((cs) << 2) + 1, (base) & 0xff ); - -#define PNP_PGCS_CSLINE_CONF(cs, conf) \ - write_pgcs_config(((cs) << 2) + 2, (conf) ); - - -/* The following sections are for 87308 extensions to the standard compoents it emulates */ - -/* extensions to 16550*/ - -#define MCR_MDSL_MSK 0xe0 /*mode select mask*/ -#define MCR_MDSL_UART 0x00 /*uart, default*/ -#define MCR_MDSL_SHRPIR 0x02 /*Sharp IR*/ -#define MCR_MDSL_SIR 0x03 /*SIR*/ -#define MCR_MDSL_CIR 0x06 /*Consumer IR*/ - -#define FCR_TXFTH0 0x10 /* these bits control threshod of data level in fifo */ -#define FCR_TXFTH1 0x20 /* for interrupt trigger */ - -/* - * Default NS87308 configuration - */ -#ifndef CONFIG_SYS_NS87308_KBC1_BASE -#define CONFIG_SYS_NS87308_KBC1_BASE 0x0060 -#endif -#ifndef CONFIG_SYS_NS87308_RTC_BASE -#define CONFIG_SYS_NS87308_RTC_BASE 0x0070 -#endif -#ifndef CONFIG_SYS_NS87308_FDC_BASE -#define CONFIG_SYS_NS87308_FDC_BASE 0x03F0 -#endif -#ifndef CONFIG_SYS_NS87308_LPT_BASE -#define CONFIG_SYS_NS87308_LPT_BASE 0x0278 -#endif -#ifndef CONFIG_SYS_NS87308_UART1_BASE -#define CONFIG_SYS_NS87308_UART1_BASE 0x03F8 -#endif -#ifndef CONFIG_SYS_NS87308_UART2_BASE -#define CONFIG_SYS_NS87308_UART2_BASE 0x02F8 -#endif - -#endif /*_NS87308_H_*/ diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 95c0ccc9d3..bca3a04e33 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -1236,7 +1236,6 @@ CONFIG_NO_WAIT CONFIG_NR_DRAM_POPULATED CONFIG_NS16550_MIN_FUNCTIONS CONFIG_NS8382X -CONFIG_NS87308 CONFIG_NUM_DSP_CPUS CONFIG_NUM_PAMU CONFIG_ODROID_REV_AIN @@ -2291,8 +2290,6 @@ CONFIG_SYS_FAST_CLK CONFIG_SYS_FAULT_ECHO_LINK_DOWN CONFIG_SYS_FAULT_MII_ADDR CONFIG_SYS_FCC_PSMR -CONFIG_SYS_FDC_DRIVE_NUMBER -CONFIG_SYS_FDC_HW_INIT CONFIG_SYS_FDT_BASE CONFIG_SYS_FDT_LOAD_ADDR CONFIG_SYS_FDT_PAD @@ -2967,8 +2964,6 @@ CONFIG_SYS_IO_BASE CONFIG_SYS_ISA_BASE CONFIG_SYS_ISA_IO CONFIG_SYS_ISA_IO_BASE_ADDRESS -CONFIG_SYS_ISA_IO_OFFSET -CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_MEM CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_JFFS2_FIRST_SECTOR @@ -3328,35 +3323,6 @@ CONFIG_SYS_NS16550_MEM32 CONFIG_SYS_NS16550_PORT_MAPPED CONFIG_SYS_NS16550_REG_SIZE CONFIG_SYS_NS16550_SERIAL -CONFIG_SYS_NS87308_CS0_BASE -CONFIG_SYS_NS87308_CS0_CONF -CONFIG_SYS_NS87308_CS1_BASE -CONFIG_SYS_NS87308_CS1_CONF -CONFIG_SYS_NS87308_CS2_BASE -CONFIG_SYS_NS87308_CS2_CONF -CONFIG_SYS_NS87308_FDC -CONFIG_SYS_NS87308_FDC_BASE -CONFIG_SYS_NS87308_GPIO -CONFIG_SYS_NS87308_GPIO_BASE -CONFIG_SYS_NS87308_KBC1 -CONFIG_SYS_NS87308_KBC1_BASE -CONFIG_SYS_NS87308_KBC2 -CONFIG_SYS_NS87308_LPT_BASE -CONFIG_SYS_NS87308_MOUSE -CONFIG_SYS_NS87308_PARP -CONFIG_SYS_NS87308_PMC1 -CONFIG_SYS_NS87308_PMC2 -CONFIG_SYS_NS87308_PMC3 -CONFIG_SYS_NS87308_POWRMAN -CONFIG_SYS_NS87308_PS2MOD -CONFIG_SYS_NS87308_PWMAN_BASE -CONFIG_SYS_NS87308_RARP -CONFIG_SYS_NS87308_RTC_APC -CONFIG_SYS_NS87308_RTC_BASE -CONFIG_SYS_NS87308_UART1 -CONFIG_SYS_NS87308_UART1_BASE -CONFIG_SYS_NS87308_UART2 -CONFIG_SYS_NS87308_UART2_BASE CONFIG_SYS_NUM_ADDR_MAP CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_FM1_10GEC