u-boot-brain/board/keymile/common/common.h

156 lines
2.9 KiB
C
Raw Normal View History

/*
* (C) Copyright 2008
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __KEYMILE_COMMON_H
#define __KEYMILE_COMMON_H
#define WRG_RESET 0x80
#define H_OPORTS_14 0x40
#define WRG_LED 0x02
#define WRL_BOOT 0x01
#define OPRTL_XBUFENA 0x20
#define H_OPORTS_SCC4_ENA 0x10
#define H_OPORTS_SCC4_FD_ENA 0x04
#define H_OPORTS_FCC1_PW_DWN 0x01
#define PIGGY_PRESENT 0x80
struct km_bec_fpga {
unsigned char id;
unsigned char rev;
unsigned char oprth;
unsigned char oprtl;
unsigned char res1[3];
unsigned char bprth;
unsigned char bprtl;
unsigned char gprt3;
unsigned char gprt2;
unsigned char gprt1;
unsigned char gprt0;
unsigned char res2[2];
unsigned char prst;
unsigned char res3[0xfff0];
unsigned char pgy_id;
unsigned char pgy_rev;
unsigned char pgy_outputs;
unsigned char pgy_eth;
};
#define BFTICU_DIPSWITCH_MASK 0x0f
/*
* BFTICU FPGA iomap
* BFTICU is used on mgcoge and mgocge3ne
*/
struct bfticu_iomap {
u8 xi_ena; /* General defect enable */
u8 pack1[3];
u8 en_csn;
u8 pack2;
u8 safe_mem;
u8 pack3;
u8 id;
u8 pack4;
u8 rev;
u8 build;
u8 p_frc;
u8 p_msk;
u8 pack5[2];
u8 xg_int;
u8 pack6[15];
u8 s_conf;
u8 pack7;
u8 dmx_conf12;
u8 pack8;
u8 s_clkslv;
u8 pack9[11];
u8 d_conf;
u8 d_mask_ca;
u8 d_pll_del;
u8 pack10[16];
u8 t_conf_ca;
u8 t_mask_ca;
u8 pack11[13];
u8 m_def0;
u8 m_def1;
u8 m_def2;
u8 m_def3;
u8 m_def4;
u8 m_def5;
u8 m_def_trap0;
u8 m_def_trap1;
u8 m_def_trap2;
u8 m_def_trap3;
u8 m_def_trap4;
u8 m_def_trap5;
u8 m_mask_def0;
u8 m_mask_def1;
u8 m_mask_def2;
u8 m_mask_def3;
u8 m_mask_def4;
u8 m_mask_def5;
u8 m_def_mask0;
u8 m_def_mask1;
u8 m_def_mask2;
u8 m_def_mask3;
u8 m_def_mask4;
u8 m_def_mask5;
u8 m_def_pri;
u8 pack12[11];
u8 hw_status;
u8 pack13;
u8 hw_control1;
u8 hw_control2;
u8 hw_control3;
u8 pack14[7];
u8 led_on; /* Leds */
u8 pack15;
u8 sfp_control; /* SFP modules */
u8 pack16;
u8 alarm_control; /* Alarm output */
u8 pack17;
u8 icps; /* ICN clock pulse shaping */
u8 mswitch; /* Read mode switch */
u8 pack18[6];
u8 pb_dbug;
};
#if !defined(CONFIG_PIGGY_MAC_ADRESS_OFFSET)
#define CONFIG_PIGGY_MAC_ADRESS_OFFSET 0
#endif
int ethernet_present(void);
int ivm_read_eeprom(unsigned char *buf, int len);
int ivm_analyze_eeprom(unsigned char *buf, int len);
int trigger_fpga_config(void);
int wait_for_fpga_config(void);
int fpga_reset(void);
int toggle_eeprom_spi_bus(void);
int get_testpin(void);
int set_km_env(void);
int fdt_set_node_and_value(void *blob,
powerpc: updates for the keymile boards - CONFIG_SYS_MAX_I2C_BUS changed to 1 We use only one I2C hardwarecontroller on this boards, so change the CONFIG_SYS_MAX_I2C_BUS to 1. - common: dont print errormsg if second IVM Block lacks. - 82xx, mgcoge: fix double mtdpart entry in environment - 82xx, mgcoge: activate on second Flash the second bank. - common: CONFIG_ENV_SIZE 0x4000 for all keymile boards - common: Change malloc size to 1MByte for all Keymile boards We need a bigger malloc area for the environment support (128k) on some Keymile boards (kmeter1) and the upcoming UBI support. Change it to 1MB for all Keymile boards to be on the save side. Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for UBI/UBIFS support. - Add UBI support to all Keymile boards - change manner of writing "/localbus/ranges" node instead of writting the complete "/localbus/ranges" node before booting Linux, only update the ranges entries which gets dynamical detected (size of flashes). This is needed, because keymile adds in the DTS "/localbus/ranges" node entries, which u-boot must not overwrite/delete. - kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips The Intel P30 chip has 2 non-identical chips on one die, so we need to define 2 seperate regions that are scanned by physmap_of independantly. - kmeter1: Add MTD concat support to Keymile boards - 82xx, mgcoge: add "unlock=yes" to default environment - added CONFIG_MTD_DEVICE to get in sync with mainline code Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-09 19:04:18 +09:00
char *nodename,
char *regname,
void *var,
int size);
int fdt_get_node_and_value(void *blob,
powerpc: updates for the keymile boards - CONFIG_SYS_MAX_I2C_BUS changed to 1 We use only one I2C hardwarecontroller on this boards, so change the CONFIG_SYS_MAX_I2C_BUS to 1. - common: dont print errormsg if second IVM Block lacks. - 82xx, mgcoge: fix double mtdpart entry in environment - 82xx, mgcoge: activate on second Flash the second bank. - common: CONFIG_ENV_SIZE 0x4000 for all keymile boards - common: Change malloc size to 1MByte for all Keymile boards We need a bigger malloc area for the environment support (128k) on some Keymile boards (kmeter1) and the upcoming UBI support. Change it to 1MB for all Keymile boards to be on the save side. Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for UBI/UBIFS support. - Add UBI support to all Keymile boards - change manner of writing "/localbus/ranges" node instead of writting the complete "/localbus/ranges" node before booting Linux, only update the ranges entries which gets dynamical detected (size of flashes). This is needed, because keymile adds in the DTS "/localbus/ranges" node entries, which u-boot must not overwrite/delete. - kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips The Intel P30 chip has 2 non-identical chips on one die, so we need to define 2 seperate regions that are scanned by physmap_of independantly. - kmeter1: Add MTD concat support to Keymile boards - 82xx, mgcoge: add "unlock=yes" to default environment - added CONFIG_MTD_DEVICE to get in sync with mainline code Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-09 19:04:18 +09:00
char *nodename,
char *propname,
void **var);
#define DELAY_ABORT_SEQ 62 /* @200kHz 9 clocks = 44us, 62us is ok */
#define DELAY_HALF_PERIOD (500 / (CONFIG_SYS_I2C_SPEED / 1000))
int i2c_soft_read_pin(void);
int i2c_make_abort(void);
#endif /* __KEYMILE_COMMON_H */