mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-19 16:38:53 +09:00
98 lines
2.8 KiB
C
98 lines
2.8 KiB
C
![]() |
/* SPDX-License-Identifier: GPL-2.0+ */
|
||
|
|
||
|
#ifndef _CONFIG_DB_88F6281_BP_H
|
||
|
#define _CONFIG_DB_88F6281_BP_H
|
||
|
|
||
|
/*
|
||
|
* High Level Configuration Options (easy to change)
|
||
|
*/
|
||
|
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
|
||
|
#define CONFIG_KW88F6281 1 /* SOC Name */
|
||
|
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
|
||
|
#define CONFIG_SYS_TCLK 166666667
|
||
|
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
|
||
|
#define CONFIG_BUILD_TARGET "u-boot.kwb"
|
||
|
|
||
|
/* additions for new ARM relocation support */
|
||
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
||
|
|
||
|
#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
|
||
|
#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
|
||
|
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
|
||
|
#define CONFIG_KIRKWOOD_GPIO 1
|
||
|
|
||
|
/*
|
||
|
* NS16550 Configuration
|
||
|
*/
|
||
|
#define CONFIG_SYS_NS16550_SERIAL
|
||
|
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
|
||
|
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
|
||
|
#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
|
||
|
|
||
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
||
|
/*
|
||
|
* Serial Port configuration
|
||
|
* The following definitions let you select what serial you want to use
|
||
|
* for your console driver.
|
||
|
*/
|
||
|
|
||
|
#define CONFIG_CONS_INDEX 1 /* Console on UART0 */
|
||
|
|
||
|
/*
|
||
|
* Environment variables configurations
|
||
|
*/
|
||
|
#define CONFIG_ENV_SPI_BUS 0
|
||
|
#define CONFIG_ENV_SPI_CS 0
|
||
|
#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
|
||
|
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
|
||
|
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
|
||
|
#define CONFIG_ENV_SIZE 0x01000
|
||
|
#define CONFIG_ENV_OFFSET 0xC0000
|
||
|
|
||
|
/*
|
||
|
* U-Boot bootcode configuration
|
||
|
*/
|
||
|
|
||
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
|
||
|
#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
|
||
|
|
||
|
/*
|
||
|
* For booting Linux, the board info and command line data
|
||
|
* have to be in the first 8 MB of memory, since this is
|
||
|
* the maximum mapped by the Linux kernel during initialization.
|
||
|
*/
|
||
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
|
||
|
|
||
|
/* size in bytes reserved for initial data */
|
||
|
|
||
|
#include <asm/arch/config.h>
|
||
|
/* There is no PHY directly connected so don't ask it for link status */
|
||
|
#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
||
|
|
||
|
/*
|
||
|
* Other required minimal configurations
|
||
|
*/
|
||
|
#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
|
||
|
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
|
||
|
#define CONFIG_SYS_MEMTEST_END 0x007fffff /* (_8M - 1) */
|
||
|
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
|
||
|
|
||
|
/*
|
||
|
* SDIO/MMC Card Configuration
|
||
|
*/
|
||
|
#ifdef CONFIG_CMD_MMC
|
||
|
#define CONFIG_MVEBU_MMC
|
||
|
#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
|
||
|
#endif /* CONFIG_CMD_MMC */
|
||
|
|
||
|
/*
|
||
|
* SATA Driver configuration
|
||
|
*/
|
||
|
#ifdef CONFIG_MVSATA_IDE
|
||
|
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
|
||
|
#endif /*CONFIG_MVSATA_IDE*/
|
||
|
|
||
|
#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
|
||
|
|
||
|
#endif /* _CONFIG_DB_88F6281_BP_H */
|