2018-05-07 06:58:06 +09:00
|
|
|
// SPDX-License-Identifier: GPL-2.0+
|
2018-04-05 16:04:38 +09:00
|
|
|
/*
|
|
|
|
* K+P iMX6Q KP_IMX6Q_TPC board configuration
|
|
|
|
*
|
|
|
|
* Copyright (C) 2018 Lukasz Majewski <lukma@denx.de>
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <common.h>
|
|
|
|
#include <asm/arch/clock.h>
|
|
|
|
#include <asm/arch/crm_regs.h>
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
|
|
#include <asm/arch/mx6-pins.h>
|
|
|
|
#include <asm/arch/sys_proto.h>
|
|
|
|
#include <asm/mach-imx/boot_mode.h>
|
2019-08-02 00:46:51 +09:00
|
|
|
#include <env.h>
|
2018-04-05 16:04:38 +09:00
|
|
|
#include <errno.h>
|
|
|
|
#include <miiphy.h>
|
|
|
|
#include <usb.h>
|
|
|
|
#include <usb/ehci-ci.h>
|
2019-10-10 23:11:26 +09:00
|
|
|
#include <led.h>
|
2018-04-05 16:04:38 +09:00
|
|
|
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
|
|
|
|
int dram_init(void)
|
|
|
|
{
|
|
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Do not overwrite the console
|
|
|
|
* Use always serial for U-Boot console
|
|
|
|
*/
|
|
|
|
int overwrite_console(void)
|
|
|
|
{
|
|
|
|
return 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
|
|
static int setup_fec_clock(void)
|
|
|
|
{
|
|
|
|
struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
|
|
|
|
|
|
|
|
/* set gpr1[21] to select anatop clock */
|
2019-10-10 23:11:25 +09:00
|
|
|
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK,
|
|
|
|
IOMUXC_GPR1_ENET_CLK_SEL_MASK);
|
2018-04-05 16:04:38 +09:00
|
|
|
|
|
|
|
return enable_fec_anatop_clock(0, ENET_50MHZ);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ar8031_phy_fixup(struct phy_device *phydev)
|
|
|
|
{
|
|
|
|
unsigned short val;
|
|
|
|
|
|
|
|
/* To enable AR8031 output a 125MHz clk from CLK_25M */
|
|
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
|
|
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
|
|
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
|
|
|
|
|
|
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
|
|
|
|
val &= 0xffe3;
|
|
|
|
val |= 0x18;
|
|
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
|
|
|
|
|
|
|
|
/* introduce tx clock delay */
|
|
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
|
|
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
|
|
|
|
val |= 0x0100;
|
|
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
|
|
{
|
|
|
|
ar8031_phy_fixup(phydev);
|
|
|
|
|
|
|
|
if (phydev->drv->config)
|
|
|
|
phydev->drv->config(phydev);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
#endif
|
|
|
|
|
|
|
|
#ifdef CONFIG_USB_EHCI_MX6
|
|
|
|
static void setup_usb(void)
|
|
|
|
{
|
|
|
|
/*
|
|
|
|
* Set daisy chain for otg_pin_id on MX6Q.
|
|
|
|
* For MX6DL, this bit is reserved.
|
|
|
|
*/
|
|
|
|
imx_iomux_set_gpr_register(1, 13, 1, 0);
|
|
|
|
}
|
|
|
|
#endif
|
|
|
|
|
|
|
|
int board_early_init_f(void)
|
|
|
|
{
|
|
|
|
#ifdef CONFIG_USB_EHCI_MX6
|
|
|
|
setup_usb();
|
|
|
|
#endif
|
|
|
|
|
2019-10-10 23:11:29 +09:00
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
|
|
setup_fec_clock();
|
|
|
|
#endif
|
|
|
|
|
2018-04-05 16:04:38 +09:00
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int board_init(void)
|
|
|
|
{
|
|
|
|
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
|
|
|
|
|
|
/* address of boot parameters */
|
|
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
|
|
|
|
/* Enable eim_slow clocks */
|
|
|
|
setbits_le32(&mxc_ccm->CCGR6, 0x1 << MXC_CCM_CCGR6_EMI_SLOW_OFFSET);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
#ifdef CONFIG_CMD_BMODE
|
|
|
|
static const struct boot_mode board_boot_modes[] = {
|
|
|
|
/* 4 bit bus width */
|
|
|
|
{"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
|
|
|
|
/* 8 bit bus width */
|
|
|
|
{"emmc", MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
|
|
|
|
{NULL, 0},
|
|
|
|
};
|
|
|
|
#endif
|
|
|
|
|
|
|
|
int board_late_init(void)
|
|
|
|
{
|
|
|
|
#ifdef CONFIG_CMD_BMODE
|
|
|
|
add_board_boot_modes(board_boot_modes);
|
|
|
|
#endif
|
|
|
|
|
2019-10-10 23:11:26 +09:00
|
|
|
if (IS_ENABLED(CONFIG_LED))
|
|
|
|
led_default_state();
|
|
|
|
|
2018-04-05 16:04:38 +09:00
|
|
|
env_set("boardname", "kp-tpc");
|
|
|
|
env_set("boardsoc", "imx6q");
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int checkboard(void)
|
|
|
|
{
|
|
|
|
puts("Board: K+P KP_IMX6Q_TPC i.MX6Q\n");
|
|
|
|
return 0;
|
|
|
|
}
|