u-boot-brain/board/tqc/tqma6/Makefile

# SPDX-License-Identifier: GPL-2.0+
#
# Copyright (C) 2014, Markus Niebel <Markus.Niebel@tq-group.com>

obj-y  := tqma6.o

obj-$(CONFIG_MBA6) += tqma6_mba6.o
obj-$(CONFIG_WRU4) += tqma6_wru4.o
SPDX: Convert all of our single license tags to Linux Kernel style When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com> 2018-05-07 06:58:06 +09:00			`# SPDX-License-Identifier: GPL-2.0+`
Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com> 2014-07-18 23:52:44 +09:00			`#`
			`# Copyright (C) 2014, Markus Niebel <Markus.Niebel@tq-group.com>`

			`obj-y := tqma6.o`

			`obj-$(CONFIG_MBA6) += tqma6_mba6.o`
arm: mx6: tqma6: Add WRU-IV baseboard for the TQMa6 SoM This patch adds support for the "OHB System AG" baseboard with is equipped with the TQMa6S SoM. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de> 2015-07-06 20:36:33 +09:00			`obj-$(CONFIG_WRU4) += tqma6_wru4.o`