mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-19 08:28:51 +09:00
123 lines
2.9 KiB
Plaintext
123 lines
2.9 KiB
Plaintext
![]() |
TPS65090 regulators
|
||
|
|
||
|
Required properties:
|
||
|
- compatible: "ti,tps65090"
|
||
|
- reg: I2C slave address
|
||
|
- interrupts: the interrupt outputs of the controller
|
||
|
- regulators: A node that houses a sub-node for each regulator within the
|
||
|
device. Each sub-node is identified using the node's name, with valid
|
||
|
values listed below. The content of each sub-node is defined by the
|
||
|
standard binding for regulators; see regulator.txt.
|
||
|
dcdc[1-3], fet[1-7] and ldo[1-2] respectively.
|
||
|
- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively.
|
||
|
- infet[1-7]-supply: The input supply for FET[1-7] respectively.
|
||
|
- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively.
|
||
|
|
||
|
Optional properties:
|
||
|
- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||
|
If DCDCs are externally controlled then this property should be there.
|
||
|
- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||
|
If DCDCs are externally controlled and if it is from GPIO then GPIO
|
||
|
number should be provided. If it is externally controlled and no GPIO
|
||
|
entry then driver will just configure this rails as external control
|
||
|
and will not provide any enable/disable APIs.
|
||
|
|
||
|
Each regulator is defined using the standard binding for regulators.
|
||
|
|
||
|
Example:
|
||
|
|
||
|
tps65090@48 {
|
||
|
compatible = "ti,tps65090";
|
||
|
reg = <0x48>;
|
||
|
interrupts = <0 88 0x4>;
|
||
|
|
||
|
vsys1-supply = <&some_reg>;
|
||
|
vsys2-supply = <&some_reg>;
|
||
|
vsys3-supply = <&some_reg>;
|
||
|
infet1-supply = <&some_reg>;
|
||
|
infet2-supply = <&some_reg>;
|
||
|
infet3-supply = <&some_reg>;
|
||
|
infet4-supply = <&some_reg>;
|
||
|
infet5-supply = <&some_reg>;
|
||
|
infet6-supply = <&some_reg>;
|
||
|
infet7-supply = <&some_reg>;
|
||
|
vsys_l1-supply = <&some_reg>;
|
||
|
vsys_l2-supply = <&some_reg>;
|
||
|
|
||
|
regulators {
|
||
|
dcdc1 {
|
||
|
regulator-name = "dcdc1";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
ti,enable-ext-control;
|
||
|
dcdc-ext-control-gpios = <&gpio 10 0>;
|
||
|
};
|
||
|
|
||
|
dcdc2 {
|
||
|
regulator-name = "dcdc2";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
dcdc3 {
|
||
|
regulator-name = "dcdc3";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
fet1 {
|
||
|
regulator-name = "fet1";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
fet2 {
|
||
|
regulator-name = "fet2";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
fet3 {
|
||
|
regulator-name = "fet3";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
fet4 {
|
||
|
regulator-name = "fet4";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
fet5 {
|
||
|
regulator-name = "fet5";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
fet6 {
|
||
|
regulator-name = "fet6";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
fet7 {
|
||
|
regulator-name = "fet7";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
ldo1 {
|
||
|
regulator-name = "ldo1";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
|
||
|
ldo2 {
|
||
|
regulator-name = "ldo2";
|
||
|
regulator-boot-on;
|
||
|
regulator-always-on;
|
||
|
};
|
||
|
};
|
||
|
};
|