mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-08-29 05:18:51 +09:00
312 lines
6.6 KiB
C
312 lines
6.6 KiB
C
![]() |
/*
|
||
|
* Freescale i.MX28 OCOTP Driver
|
||
|
*
|
||
|
* Copyright (C) 2014 Marek Vasut <marex@denx.de>
|
||
|
*
|
||
|
* SPDX-License-Identifier: GPL-2.0+
|
||
|
*
|
||
|
* Note: The i.MX23/i.MX28 OCOTP block is a predecessor to the OCOTP block
|
||
|
* used in i.MX6 . While these blocks are very similar at the first
|
||
|
* glance, by digging deeper, one will notice differences (like the
|
||
|
* tight dependence on MXS power block, some completely new registers
|
||
|
* etc.) which would make common driver an ifdef nightmare :-(
|
||
|
*/
|
||
|
|
||
|
#include <common.h>
|
||
|
#include <fuse.h>
|
||
|
#include <asm/errno.h>
|
||
|
#include <asm/io.h>
|
||
|
#include <asm/arch/clock.h>
|
||
|
#include <asm/arch/imx-regs.h>
|
||
|
#include <asm/arch/sys_proto.h>
|
||
|
|
||
|
#define MXS_OCOTP_TIMEOUT 100000
|
||
|
|
||
|
static struct mxs_ocotp_regs *ocotp_regs =
|
||
|
(struct mxs_ocotp_regs *)MXS_OCOTP_BASE;
|
||
|
static struct mxs_power_regs *power_regs =
|
||
|
(struct mxs_power_regs *)MXS_POWER_BASE;
|
||
|
static struct mxs_clkctrl_regs *clkctrl_regs =
|
||
|
(struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
|
||
|
|
||
|
static int mxs_ocotp_wait_busy_clear(void)
|
||
|
{
|
||
|
uint32_t reg;
|
||
|
int timeout = MXS_OCOTP_TIMEOUT;
|
||
|
|
||
|
while (--timeout) {
|
||
|
reg = readl(&ocotp_regs->hw_ocotp_ctrl);
|
||
|
if (!(reg & OCOTP_CTRL_BUSY))
|
||
|
break;
|
||
|
udelay(10);
|
||
|
}
|
||
|
|
||
|
if (!timeout)
|
||
|
return -EINVAL;
|
||
|
|
||
|
/* Wait a little as per FSL datasheet's 'write postamble' section. */
|
||
|
udelay(10);
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
static void mxs_ocotp_clear_error(void)
|
||
|
{
|
||
|
writel(OCOTP_CTRL_ERROR, &ocotp_regs->hw_ocotp_ctrl_clr);
|
||
|
}
|
||
|
|
||
|
static int mxs_ocotp_read_bank_open(bool open)
|
||
|
{
|
||
|
int ret = 0;
|
||
|
|
||
|
if (open) {
|
||
|
writel(OCOTP_CTRL_RD_BANK_OPEN,
|
||
|
&ocotp_regs->hw_ocotp_ctrl_set);
|
||
|
|
||
|
/*
|
||
|
* Wait before polling the BUSY bit, since the BUSY bit might
|
||
|
* be asserted only after a few HCLK cycles and if we were to
|
||
|
* poll immediatelly, we could miss the busy bit.
|
||
|
*/
|
||
|
udelay(10);
|
||
|
ret = mxs_ocotp_wait_busy_clear();
|
||
|
} else {
|
||
|
writel(OCOTP_CTRL_RD_BANK_OPEN,
|
||
|
&ocotp_regs->hw_ocotp_ctrl_clr);
|
||
|
}
|
||
|
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
static void mxs_ocotp_scale_vddio(bool enter, uint32_t *val)
|
||
|
{
|
||
|
uint32_t scale_val;
|
||
|
|
||
|
if (enter) {
|
||
|
/*
|
||
|
* Enter the fuse programming VDDIO voltage setup. We start
|
||
|
* scaling the voltage from it's current value down to 2.8V
|
||
|
* which is the one and only correct voltage for programming
|
||
|
* the OCOTP fuses (according to datasheet).
|
||
|
*/
|
||
|
scale_val = readl(&power_regs->hw_power_vddioctrl);
|
||
|
scale_val &= POWER_VDDIOCTRL_TRG_MASK;
|
||
|
|
||
|
/* Return the original voltage. */
|
||
|
*val = scale_val;
|
||
|
|
||
|
/*
|
||
|
* Start scaling VDDIO down to 0x2, which is 2.8V . Actually,
|
||
|
* the value 0x0 should be 2.8V, but that's not the case on
|
||
|
* most designs due to load etc., so we play safe. Undervolt
|
||
|
* can actually cause incorrect programming of the fuses and
|
||
|
* or reboots of the board.
|
||
|
*/
|
||
|
while (scale_val > 2) {
|
||
|
clrsetbits_le32(&power_regs->hw_power_vddioctrl,
|
||
|
POWER_VDDIOCTRL_TRG_MASK, --scale_val);
|
||
|
udelay(500);
|
||
|
}
|
||
|
} else {
|
||
|
/* Start scaling VDDIO up to original value . */
|
||
|
for (scale_val = 2; scale_val <= *val; scale_val++) {
|
||
|
clrsetbits_le32(&power_regs->hw_power_vddioctrl,
|
||
|
POWER_VDDIOCTRL_TRG_MASK, scale_val);
|
||
|
udelay(500);
|
||
|
}
|
||
|
}
|
||
|
|
||
|
mdelay(10);
|
||
|
}
|
||
|
|
||
|
static int mxs_ocotp_wait_hclk_ready(void)
|
||
|
{
|
||
|
uint32_t reg, timeout = MXS_OCOTP_TIMEOUT;
|
||
|
|
||
|
while (--timeout) {
|
||
|
reg = readl(&clkctrl_regs->hw_clkctrl_hbus);
|
||
|
if (!(reg & CLKCTRL_HBUS_ASM_BUSY))
|
||
|
break;
|
||
|
}
|
||
|
|
||
|
if (!timeout)
|
||
|
return -EINVAL;
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
static int mxs_ocotp_scale_hclk(bool enter, uint32_t *val)
|
||
|
{
|
||
|
uint32_t scale_val;
|
||
|
int ret;
|
||
|
|
||
|
ret = mxs_ocotp_wait_hclk_ready();
|
||
|
if (ret)
|
||
|
return ret;
|
||
|
|
||
|
/* Set CPU bypass */
|
||
|
writel(CLKCTRL_CLKSEQ_BYPASS_CPU,
|
||
|
&clkctrl_regs->hw_clkctrl_clkseq_set);
|
||
|
|
||
|
if (enter) {
|
||
|
/* Return the original HCLK clock speed. */
|
||
|
*val = readl(&clkctrl_regs->hw_clkctrl_hbus);
|
||
|
*val &= CLKCTRL_HBUS_DIV_MASK;
|
||
|
|
||
|
/* Scale the HCLK to 454/19 = 23.9 MHz . */
|
||
|
scale_val = (~19) << CLKCTRL_HBUS_DIV_OFFSET;
|
||
|
scale_val &= CLKCTRL_HBUS_DIV_MASK;
|
||
|
} else {
|
||
|
/* Scale the HCLK back to original frequency. */
|
||
|
scale_val = (~(*val)) << CLKCTRL_HBUS_DIV_OFFSET;
|
||
|
scale_val &= CLKCTRL_HBUS_DIV_MASK;
|
||
|
}
|
||
|
|
||
|
writel(CLKCTRL_HBUS_DIV_MASK,
|
||
|
&clkctrl_regs->hw_clkctrl_hbus_set);
|
||
|
writel(scale_val,
|
||
|
&clkctrl_regs->hw_clkctrl_hbus_clr);
|
||
|
|
||
|
mdelay(10);
|
||
|
|
||
|
ret = mxs_ocotp_wait_hclk_ready();
|
||
|
if (ret)
|
||
|
return ret;
|
||
|
|
||
|
/* Disable CPU bypass */
|
||
|
writel(CLKCTRL_CLKSEQ_BYPASS_CPU,
|
||
|
&clkctrl_regs->hw_clkctrl_clkseq_clr);
|
||
|
|
||
|
mdelay(10);
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
static int mxs_ocotp_write_fuse(uint32_t addr, uint32_t mask)
|
||
|
{
|
||
|
uint32_t hclk_val, vddio_val;
|
||
|
int ret;
|
||
|
|
||
|
/* Make sure the banks are closed for reading. */
|
||
|
ret = mxs_ocotp_read_bank_open(0);
|
||
|
if (ret) {
|
||
|
puts("Failed closing banks for reading!\n");
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
ret = mxs_ocotp_scale_hclk(1, &hclk_val);
|
||
|
if (ret) {
|
||
|
puts("Failed scaling down the HCLK!\n");
|
||
|
return ret;
|
||
|
}
|
||
|
mxs_ocotp_scale_vddio(1, &vddio_val);
|
||
|
|
||
|
ret = mxs_ocotp_wait_busy_clear();
|
||
|
if (ret) {
|
||
|
puts("Failed waiting for ready state!\n");
|
||
|
goto fail;
|
||
|
}
|
||
|
|
||
|
/* Program the fuse address */
|
||
|
writel(addr | OCOTP_CTRL_WR_UNLOCK_KEY, &ocotp_regs->hw_ocotp_ctrl);
|
||
|
|
||
|
/* Program the data. */
|
||
|
writel(mask, &ocotp_regs->hw_ocotp_data);
|
||
|
|
||
|
udelay(10);
|
||
|
|
||
|
ret = mxs_ocotp_wait_busy_clear();
|
||
|
if (ret) {
|
||
|
puts("Failed waiting for ready state!\n");
|
||
|
goto fail;
|
||
|
}
|
||
|
|
||
|
fail:
|
||
|
mxs_ocotp_scale_vddio(0, &vddio_val);
|
||
|
ret = mxs_ocotp_scale_hclk(0, &hclk_val);
|
||
|
if (ret) {
|
||
|
puts("Failed scaling up the HCLK!\n");
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
static int mxs_ocotp_read_fuse(uint32_t reg, uint32_t *val)
|
||
|
{
|
||
|
int ret;
|
||
|
|
||
|
/* Register offset from CUST0 */
|
||
|
reg = ((uint32_t)&ocotp_regs->hw_ocotp_cust0) + (reg << 4);
|
||
|
|
||
|
ret = mxs_ocotp_wait_busy_clear();
|
||
|
if (ret) {
|
||
|
puts("Failed waiting for ready state!\n");
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
mxs_ocotp_clear_error();
|
||
|
|
||
|
ret = mxs_ocotp_read_bank_open(1);
|
||
|
if (ret) {
|
||
|
puts("Failed opening banks for reading!\n");
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
*val = readl(reg);
|
||
|
|
||
|
ret = mxs_ocotp_read_bank_open(0);
|
||
|
if (ret) {
|
||
|
puts("Failed closing banks for reading!\n");
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
static int mxs_ocotp_valid(u32 bank, u32 word)
|
||
|
{
|
||
|
if (bank > 4)
|
||
|
return -EINVAL;
|
||
|
if (word > 7)
|
||
|
return -EINVAL;
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
/*
|
||
|
* The 'fuse' command API
|
||
|
*/
|
||
|
int fuse_read(u32 bank, u32 word, u32 *val)
|
||
|
{
|
||
|
int ret;
|
||
|
|
||
|
ret = mxs_ocotp_valid(bank, word);
|
||
|
if (ret)
|
||
|
return ret;
|
||
|
|
||
|
return mxs_ocotp_read_fuse((bank << 3) | word, val);
|
||
|
}
|
||
|
|
||
|
int fuse_prog(u32 bank, u32 word, u32 val)
|
||
|
{
|
||
|
int ret;
|
||
|
|
||
|
ret = mxs_ocotp_valid(bank, word);
|
||
|
if (ret)
|
||
|
return ret;
|
||
|
|
||
|
return mxs_ocotp_write_fuse((bank << 3) | word, val);
|
||
|
}
|
||
|
|
||
|
int fuse_sense(u32 bank, u32 word, u32 *val)
|
||
|
{
|
||
|
/* We do not support sensing :-( */
|
||
|
return -EINVAL;
|
||
|
}
|
||
|
|
||
|
int fuse_override(u32 bank, u32 word, u32 val)
|
||
|
{
|
||
|
/* We do not support overriding :-( */
|
||
|
return -EINVAL;
|
||
|
}
|