u-boot-brain/configs/zynq_zc706_defconfig

CONFIG_ARM=y
CONFIG_ARCH_ZYNQ=y
CONFIG_TARGET_ZYNQ_ZC706=y
CONFIG_DEFAULT_DEVICE_TREE="zynq-zc706"
CONFIG_SPL=y
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_FIT_SIGNATURE=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_SEPARATE=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPI_FLASH=y
CONFIG_ZYNQ_QSPI=y
ARM: zynq: add separate configuration for ZC702 and ZC706 Prior to this commit, ZC702 and ZC706 shared the same configuration and were built as follows: ZC702: make zynq_zc70x_defconfig && make ZC706: make zynq_zc70x_defconfig && make DEVICE_TREE=zynq-zc706 This commit introduces separate configuration for them, which makes the next commit much easier. Going forward, the recommended build commands are: ZC702: make zynq_zc702_defconfig && make ZC706: make zynq_zc706_defconfig && make Although the old work flow is still supported, CONFIG_TARGET_ZC70X has been marked as deprecated. If used, the warning message is shown to prompt users to switch to the new scheme. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> 2015-05-18 15:31:51 +09:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_ZYNQ=y`
			`CONFIG_TARGET_ZYNQ_ZC706=y`
			`CONFIG_DEFAULT_DEVICE_TREE="zynq-zc706"`
			`CONFIG_SPL=y`
			`CONFIG_FIT=y`
			`CONFIG_FIT_VERBOSE=y`
			`CONFIG_FIT_SIGNATURE=y`
Move defaults from config_cmd_default.h to Kconfig This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com> 2015-06-23 06:15:30 +09:00			`# CONFIG_CMD_IMLS is not set`
			`# CONFIG_CMD_FLASH is not set`
			`# CONFIG_CMD_SETEXPR is not set`
arm: zynq: Use separate device tree instead of embedded Production boards should not use CONFIG_OF_EMBED. Fix this for the Zybo boards. The image to use now becomes u-boot-dtb.bin. For example, the .bif file should contain a line like: [load = 0x04000000,startup=0x04000000]/path/to/u-boot-dtb.bin instead of: [load = 0x04000000,startup=0x04000000]/path/to/u-boot.bin When device tree is enabled we need to load u-boot-dtb.img. Change the settings so that SPL does the right thing. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com> 2015-10-18 10:41:20 +09:00			`CONFIG_OF_SEPARATE=y`
zynq: enable CONFIG_NET_RANDOM_ETHADDR We have to set a MAC address to use network. Otherwise, the tftpboot command fails with the following message: Gem.e000b000 Waiting for PHY auto negotiation to complete........ done *** ERROR: `ethaddr' not set Since commit 92ac52082140 ("net: Remove all references to CONFIG_ETHADDR and friends"), we can not use CONFIG_ETHADDR. The easiest way to set a MAC address is to enable CONFIG_NET_RANDOM_ETHADDR. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> 2015-07-17 20:26:06 +09:00			`CONFIG_NET_RANDOM_ETHADDR=y`
configs: Enable legacy SPI flash interface support Enable legacy spi-flash interface support for boards which supports qspi controller with connected spi-nor flash. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Jagan Teki <jteki@openedev.com> 2015-08-31 21:06:03 +09:00			`CONFIG_SPI_FLASH=y`
configs: zynq: Enable zynq qspi controller Enable zynq qspi controller driver on respective zynq boards. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Jagan Teki <jteki@openedev.com> 2015-08-31 21:08:40 +09:00			`CONFIG_ZYNQ_QSPI=y`