2014-06-24 07:15:56 +09:00
|
|
|
/*
|
|
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
|
|
*
|
|
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <common.h>
|
|
|
|
#include <fsl_ddr_sdram.h>
|
|
|
|
#include <fsl_ddr_dimm_params.h>
|
2016-04-05 03:41:26 +09:00
|
|
|
#include <asm/arch/soc.h>
|
2014-06-24 07:15:56 +09:00
|
|
|
#include "ddr.h"
|
|
|
|
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
|
|
dimm_params_t *pdimm,
|
|
|
|
unsigned int ctrl_num)
|
|
|
|
{
|
|
|
|
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
|
|
|
ulong ddr_freq;
|
|
|
|
|
|
|
|
if (ctrl_num > 3) {
|
|
|
|
printf("Not supported controller number %d\n", ctrl_num);
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
if (!pdimm->n_ranks)
|
|
|
|
return;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* we use identical timing for all slots. If needed, change the code
|
|
|
|
* to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
|
|
|
|
*/
|
|
|
|
if (popts->registered_dimm_en)
|
2014-08-14 02:21:05 +09:00
|
|
|
pbsp = rdimms[ctrl_num];
|
2014-06-24 07:15:56 +09:00
|
|
|
else
|
2014-08-14 02:21:05 +09:00
|
|
|
pbsp = udimms[ctrl_num];
|
2014-06-24 07:15:56 +09:00
|
|
|
|
|
|
|
|
|
|
|
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
|
|
|
|
* freqency and n_banks specified in board_specific_parameters table.
|
|
|
|
*/
|
|
|
|
ddr_freq = get_ddr_freq(0) / 1000000;
|
|
|
|
while (pbsp->datarate_mhz_high) {
|
|
|
|
if (pbsp->n_ranks == pdimm->n_ranks &&
|
|
|
|
(pdimm->rank_density >> 30) >= pbsp->rank_gb) {
|
|
|
|
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
|
|
|
popts->clk_adjust = pbsp->clk_adjust;
|
|
|
|
popts->wrlvl_start = pbsp->wrlvl_start;
|
|
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
|
|
goto found;
|
|
|
|
}
|
|
|
|
pbsp_highest = pbsp;
|
|
|
|
}
|
|
|
|
pbsp++;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (pbsp_highest) {
|
|
|
|
printf("Error: board specific timing not found for data rate %lu MT/s\n"
|
|
|
|
"Trying to use the highest speed (%u) parameters\n",
|
|
|
|
ddr_freq, pbsp_highest->datarate_mhz_high);
|
|
|
|
popts->clk_adjust = pbsp_highest->clk_adjust;
|
|
|
|
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
|
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
|
|
} else {
|
|
|
|
panic("DIMM is not supported by this board");
|
|
|
|
}
|
|
|
|
found:
|
|
|
|
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
|
|
|
|
"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
|
|
|
|
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
|
|
|
|
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
|
|
|
|
pbsp->wrlvl_ctl_3);
|
2015-11-09 20:12:07 +09:00
|
|
|
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
|
2014-08-14 02:21:05 +09:00
|
|
|
if (ctrl_num == CONFIG_DP_DDR_CTRL) {
|
|
|
|
/* force DDR bus width to 32 bits */
|
|
|
|
popts->data_bus_width = 1;
|
|
|
|
popts->otf_burst_chop_en = 0;
|
|
|
|
popts->burst_length = DDR_BL8;
|
2015-01-07 06:18:51 +09:00
|
|
|
popts->bstopre = 0; /* enable auto precharge */
|
2014-08-14 02:21:05 +09:00
|
|
|
}
|
2015-11-09 20:12:07 +09:00
|
|
|
#endif
|
2014-06-24 07:15:56 +09:00
|
|
|
/*
|
|
|
|
* Factors to consider for half-strength driver enable:
|
|
|
|
* - number of DIMMs installed
|
|
|
|
*/
|
|
|
|
popts->half_strength_driver_enable = 1;
|
|
|
|
/*
|
|
|
|
* Write leveling override
|
|
|
|
*/
|
|
|
|
popts->wrlvl_override = 1;
|
|
|
|
popts->wrlvl_sample = 0xf;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Rtt and Rtt_WR override
|
|
|
|
*/
|
|
|
|
popts->rtt_override = 0;
|
|
|
|
|
|
|
|
/* Enable ZQ calibration */
|
|
|
|
popts->zq_en = 1;
|
|
|
|
|
|
|
|
#ifdef CONFIG_SYS_FSL_DDR4
|
|
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
|
|
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
|
|
|
|
DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
|
|
|
|
#else
|
|
|
|
/* DHC_EN =1, ODT = 75 Ohm */
|
|
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
|
|
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
|
|
|
|
#endif
|
|
|
|
}
|
|
|
|
|
|
|
|
#ifdef CONFIG_SYS_DDR_RAW_TIMING
|
|
|
|
dimm_params_t ddr_raw_timing = {
|
|
|
|
.n_ranks = 2,
|
|
|
|
.rank_density = 1073741824u,
|
|
|
|
.capacity = 2147483648,
|
|
|
|
.primary_sdram_width = 64,
|
|
|
|
.ec_sdram_width = 0,
|
|
|
|
.registered_dimm = 0,
|
|
|
|
.mirrored_dimm = 0,
|
|
|
|
.n_row_addr = 14,
|
|
|
|
.n_col_addr = 10,
|
|
|
|
.n_banks_per_sdram_device = 8,
|
|
|
|
.edc_config = 0,
|
|
|
|
.burst_lengths_bitmask = 0x0c,
|
|
|
|
|
|
|
|
.tckmin_x_ps = 937,
|
|
|
|
.caslat_x = 0x6FC << 4, /* 14,13,11,10,9,8,7,6 */
|
|
|
|
.taa_ps = 13090,
|
|
|
|
.twr_ps = 15000,
|
|
|
|
.trcd_ps = 13090,
|
|
|
|
.trrd_ps = 5000,
|
|
|
|
.trp_ps = 13090,
|
|
|
|
.tras_ps = 33000,
|
|
|
|
.trc_ps = 46090,
|
|
|
|
.trfc_ps = 160000,
|
|
|
|
.twtr_ps = 7500,
|
|
|
|
.trtp_ps = 7500,
|
|
|
|
.refresh_rate_ps = 7800000,
|
|
|
|
.tfaw_ps = 25000,
|
|
|
|
};
|
|
|
|
|
|
|
|
int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
|
|
|
|
unsigned int controller_number,
|
|
|
|
unsigned int dimm_number)
|
|
|
|
{
|
|
|
|
const char dimm_model[] = "Fixed DDR on board";
|
|
|
|
|
|
|
|
if (((controller_number == 0) && (dimm_number == 0)) ||
|
|
|
|
((controller_number == 1) && (dimm_number == 0))) {
|
|
|
|
memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
|
|
|
|
memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
|
|
|
|
memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
#endif
|
|
|
|
phys_size_t initdram(int board_type)
|
|
|
|
{
|
|
|
|
phys_size_t dram_size;
|
|
|
|
|
|
|
|
puts("Initializing DDR....");
|
|
|
|
|
|
|
|
puts("using SPD\n");
|
|
|
|
dram_size = fsl_ddr_sdram();
|
|
|
|
|
|
|
|
return dram_size;
|
|
|
|
}
|