mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-09-13 00:03:26 +09:00
172 lines
4.3 KiB
Plaintext
172 lines
4.3 KiB
Plaintext
![]() |
HCU5 configuration details and startup sequence
|
|||
|
|
|||
|
(C) Copyright 2007 Netstal Maschinen AG
|
|||
|
Niklaus Giger (Niklaus.Giger@netstal.com)
|
|||
|
|
|||
|
TODO:
|
|||
|
-----
|
|||
|
- Fix error: Waiting for PHY auto negotiation to complete..... TIMEOUT !
|
|||
|
- Does not occur if both EMAC are connected
|
|||
|
- Fix RTS/CTS problem (HW?)
|
|||
|
CONFIG_SERIAL_MULTI/CONFIG_SERIAL_SOFTWARE_FIFO hangs after
|
|||
|
Switching to interrupt driven serial input mode
|
|||
|
|
|||
|
Caveats:
|
|||
|
--------
|
|||
|
Errata CHIP_8: Incorrect Write to DDR SDRAM. (was not applied to sequoia.c)
|
|||
|
see hcu5.c.
|
|||
|
|
|||
|
|
|||
|
Memory Bank 0 -- Flash chip
|
|||
|
---------------------------
|
|||
|
|
|||
|
0xfff00000 - 0xffffffff
|
|||
|
|
|||
|
The flash chip is really only 512Kbytes, but the high address bit of
|
|||
|
the 1Meg region is ignored, so the flash is replicated through the
|
|||
|
region. Thus, this is consistent with a flash base address 0xfff80000.
|
|||
|
|
|||
|
The placement at the end is to be consistent with reset behavior,
|
|||
|
where the processor itself initially uses this bus to load the branch
|
|||
|
vector and start running.
|
|||
|
|
|||
|
On-Chip Memory
|
|||
|
--------------
|
|||
|
|
|||
|
0xe0010000- 0xe0013fff CFG_OCM_BASE
|
|||
|
The 440EPx includes a 16K on-chip memory that can be placed however
|
|||
|
software chooses.
|
|||
|
|
|||
|
Internal Peripherals
|
|||
|
--------------------
|
|||
|
|
|||
|
0xef600300 - 0xef6008ff
|
|||
|
|
|||
|
These are scattered various peripherals internal to the PPC440EPX
|
|||
|
chip.
|
|||
|
|
|||
|
Chip-Select 2: Flash Memory
|
|||
|
---------------------------
|
|||
|
|
|||
|
Not used
|
|||
|
|
|||
|
Chip-Select 3: CAN Interface
|
|||
|
----------------------------
|
|||
|
0xc800000: 2 Intel 82527 CAN-Controller
|
|||
|
|
|||
|
|
|||
|
Chip-Select 4: IMC-bus standard
|
|||
|
-------------------------------
|
|||
|
|
|||
|
0xcc00000: Netstal specific IO-Bus
|
|||
|
|
|||
|
|
|||
|
Chip-Select 5: IMC-bus fast (inactive)
|
|||
|
--------------------------------------
|
|||
|
|
|||
|
0xce00000: Netstal specific IO-Bus (fast, but not yet used)
|
|||
|
|
|||
|
|
|||
|
Memory Bank 1 -- DDR2
|
|||
|
-------------------------------------
|
|||
|
|
|||
|
0x00000000 - 0xfffffff # Default 256 MB
|
|||
|
|
|||
|
PCI ??
|
|||
|
|
|||
|
USB ??
|
|||
|
Only USB_STORAGE is enabled to load vxWorks
|
|||
|
from a memory stick.
|
|||
|
|
|||
|
System-LEDs ??? (Analog zu HCU4 ???)
|
|||
|
|
|||
|
Startup sequence
|
|||
|
----------------
|
|||
|
|
|||
|
(cpu/ppc4xx/resetvec.S)
|
|||
|
depending on configs option
|
|||
|
call _start_440 _start_pci oder _start
|
|||
|
|
|||
|
(cpu/ppc4xx/start.S)
|
|||
|
|
|||
|
_start_440:
|
|||
|
initialize register like
|
|||
|
CCR0
|
|||
|
debug
|
|||
|
setup interrupt vectors
|
|||
|
configure cache regions
|
|||
|
clear and setup TLB
|
|||
|
enable internal RAM
|
|||
|
jump start_ram
|
|||
|
which in turn will jump to start
|
|||
|
_start:
|
|||
|
Clear and set up some registers.
|
|||
|
Debug setup
|
|||
|
Setup the internal SRAM
|
|||
|
Setup the stack in internal SRAM
|
|||
|
setup stack pointer (r1)
|
|||
|
setup GOT
|
|||
|
call cpu_init_f /* run low-level CPU init code (from Flash) */
|
|||
|
|
|||
|
call cpu_init_f
|
|||
|
board_init_f: (lib_ppc\board.c)
|
|||
|
init_sequence defines a list of function to be called
|
|||
|
board_early_init_f: (board/netstal/hcu5/hcu5.c)
|
|||
|
We are using Bootstrap-Option A
|
|||
|
if CPR0_ICFG_RLI_MASK == 0 then set some registers and reboot
|
|||
|
Setup the GPIO pins
|
|||
|
Setup the interrupt controller polarities, triggers, etc.
|
|||
|
Ethernet, PCI, USB enable
|
|||
|
setup BOOT FLASH (Chip timing)
|
|||
|
init_baudrate,
|
|||
|
serial_init
|
|||
|
checkcpu
|
|||
|
misc_init_f #ifdef
|
|||
|
init_func_i2c #ifdef
|
|||
|
post_init_f #ifdef
|
|||
|
init_func_ram -> calls init_dram board/netstal/hcu5/sdram.c
|
|||
|
(EYE function removed!!)
|
|||
|
test_dram call
|
|||
|
|
|||
|
* Reserve memory at end of RAM for (top down in that order):
|
|||
|
* - kernel log buffer
|
|||
|
* - protected RAM
|
|||
|
* - LCD framebuffer
|
|||
|
* - monitor code
|
|||
|
* - board info struct
|
|||
|
Save local variables to board info struct
|
|||
|
call relocate_code() does not return
|
|||
|
relocate_code: (cpu/ppc4xx/start.S)
|
|||
|
-------------------------------------------------------
|
|||
|
From now on our copy is in RAM and we will run from there,
|
|||
|
starting with board_init_r
|
|||
|
-------------------------------------------------------
|
|||
|
board_init_r: (lib_ppc\board.c)
|
|||
|
setup bd function pointers
|
|||
|
trap_init
|
|||
|
flash_init: (board/netstal/hcu5/flash.c)
|
|||
|
/* setup for u-boot erase, update */
|
|||
|
setup bd flash info
|
|||
|
cpu_init_r: (cpu/ppc4xx/cpu_init.c)
|
|||
|
peripheral chip select in using defines like
|
|||
|
CFG_EBC_PB0A, CFG_EBC_PB0C from hcu5.h
|
|||
|
mem_malloc_init
|
|||
|
malloc_bin_reloc
|
|||
|
spi_init (r or f)??? (CFG_ENV_IS_IN_EEPROM)
|
|||
|
env_relocated
|
|||
|
misc_init_r(bd): (board/netstal/hcu5.c)
|
|||
|
ethaddr mit serial number erg<72>nzen
|
|||
|
Then we will somehow go into the command loop
|
|||
|
|
|||
|
Most of the HW specific code for the HCU5 may be found in
|
|||
|
include/configs/hcu5.h
|
|||
|
board/netstal/hcu5/*
|
|||
|
cpu/ppc4xx/*
|
|||
|
lib_ppc/*
|
|||
|
include/ppc440.h
|
|||
|
|
|||
|
Drivers for serial etc are found under drivers/
|
|||
|
|
|||
|
Don't ask question if you did not look at the README !!
|
|||
|
Most CFG_* and CONFIG_* switches are mentioned/explained there.
|